Question about 1995 GMC Suburban

1 Answer

1995 gmc suburban quit running

I was driving on the freeway 2 days ago and it just quit. I checked the engine management fuses and the ecm 1 fuse was blown. Replaced it and it ran for about two miles. Had it towed home and now the fuse blows as soon as you turn the ignition switch.

Posted by on

  • johng47 Jul 03, 2009

    so you think there is some sort of a short in the wire bundle?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 212 Answers

Pls check the compliete wire setting because some wire will merged inside the electrical system so you can check the complete wiring

Posted on Jul 03, 2009

  • sakthi ganesh Jul 04, 2009

    yes because once the wire merged in your electrical circust your fuse will be blows so just just check your wiring

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I was driving down the freeway at the check stablitrac light flashed, along with the warning light, and the reduced engine light. The first time it just shut down - with the battery just dead. The l


here is a little help. if you need more I am on facebook. There are 2 ignition 1 voltage circuits supplied to the Engine Control Module (ECM). The first ignition circuit is provided by the powertrain relay, through a fuse. This ignition 1 voltage circuit supplies power to all the internal ECM circuits associated with the throttle actuator control (TAC) operation. The second ignition 1 voltage circuit is supplied by the run/crank relay through a fuse, and is used to power the remaining internal ECM circuits. If the ECM detects a voltage difference between the 2 ignition 1 voltage circuits, DTC

Feb 12, 2013 | GMC Yukon XL Cars & Trucks

1 Answer

Where is the PCM on a 95 GMC suburban 2500 454 w/AT and 4wd


The ECM or PCM is usually behind the glove box mounted to the firewall.
Did you check the fuses for the ECM ? Does the check engine light come on when you turn the key switch on ?

Aug 23, 2012 | 1995 GMC Jimmy

1 Answer

2005 gmc sierra heater fan quit working. I lost the fifth speed months ago and a couple of days ago lost the other four, the first day the fan would come on sometimes while driving then quit after a while...


1-4 speed are the blower motor resister . It controls all 1-4 speeds, also it's under the passanger side dash around fan, the 5th speed runs off a fuse the is located in the fuse box. It's one of those square fuses , not the relays but fuses. The resister will run $15 and fuse $5 . Good luck. I have replace these before

Jan 03, 2011 | 2003 GMC Sierra 1500

1 Answer

Quit running on freeway. acted like ran out of gas. wouldn't restart


you will need to have the fuel pressure checked. thoses suburbans are know to have fuel pump problems especially at the age of the truck.

Sep 30, 2010 | 1995 GMC Suburban

2 Answers

My 1995 gmc suburbans service engine soon light comes on only after i drive on the freeway when i turn the car off than turn it back on the light goes out. i have just changed oil and filter problem began...


hi reset it by disconnecting the live battery connection for3 mins then re connect that has done it for me if this helps please rate it thanks

Nov 21, 2009 | 1995 GMC Suburban

1 Answer

My 2000 gmc jimmy seems to have problems shifting initially in the first gear, and lately it has been redlining to 5000 rpm before shifting from 4th gear ( i think). I feel like one day it is just going to...


1-2 shift is delayed and harsh, may not shift into OD: Check Throttle Position Sensor (TPS) for smooth and linear electrical response over the entire range of motion. If not, replace.

This is one of the things i can think of that would cause the issue you gave me. Start with that since it's simple and the other thing to is you can try resetting the ECM.

Turn the ignition key to the run position (engine not running) and pull the ECM fuse out for 30 seconds. Place fuse back in and start the engine, the engine may stall but let it. The ECM is relearning the engine and transmission and then go for a test drive after idling for 1min. The transmission my be running back good as new, if not. Have the TPS checked if not replaced. Good luck and keep me posted.

Nov 05, 2009 | 2000 GMC Jimmy

3 Answers

Ecm fuse keeps blowing


just fixed this problem, change your fuel pump module, fuel sending unit shorts out on fuel level swing arm blue wire... unfortinately you must replace it as unit because of the design, fuel pump and tank guage fuel level sending unit are a one peice item, fuel tank has to come out to change unit, about a $ 700.00 repair too... fuel pump module runs about 350 to 700 $ depending on aftermarket or factory, try to find one with a lifetime warranty even if it is $ 50.00 more worth it..labor is about $ 250 to $ 400 depending on shop labor rate... definate problem though I ahve no doubt, common problem on GM... please rate my help, thanks...

Aug 06, 2009 | 2002 GMC Yukon XL

2 Answers

1995 gmc suburban - stops while turning in reverse


How fast are you going when it "stops", and does it stop completely or slow down, or lock up? need a little more info please....

Jun 04, 2009 | 1995 GMC Suburban

1 Answer

1999 GMC Suburban 350 wont run


Per your description, it sounds like you are missing an injector pulse from the ECM.
Check the under-hood fuse box and verify the "ECM1" fuse is good (12 volt supply to injectors).
With the key in the run position, verify you have 12 volts at an injector.
Barrow or purchase a "noid" light to verify you have an injector ground pulse from the ECM.
Let me know what you find and we can proceed from there.
Regards,

May 07, 2009 | 1999 Chevrolet Suburban

1 Answer

Both drive lights quite working


drive lights as in day time running lights? if so, it's more then likely just the bulbs. as in headlights? sorry, can't think of anything off hand.

Mar 07, 2009 | 1999 GMC Suburban

Not finding what you are looking for?
1995 GMC Suburban Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...