Question about 2003 Hyundai Tiburon

1 Answer

Purge valve location on a 2003 tiburon 2L - 2003 Hyundai Tiburon

Posted by on

  • zeyes Jul 27, 2009

    From what I read, if you can blow through it, it is stuck open. If it's good, you cannot blow air through it.

  • Ronald Tyler
    Ronald Tyler May 11, 2010

    how do i check it

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 94 Answers

On your Tiburon the purge valve is located below the throttle body. It is easier to access if you remove the boot between the airbox and the throttle body. After removing the boot look under the throttle body, the purge valve will be found mounted in a rubber hangar and it has a vacuum hose to both ends.

Posted on Jul 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the purge valve located


I assume you are taking about the evap system purge valve - the purge valve is located behind the EGR valve on the left side of the engine.

Mar 12, 2015 | 2003 Cadillac Deville

1 Answer

My 2003 hyundai tiburon 2L iddles at a steady 4000 rpm and wont iddle down. How do I fix this??


There r 2 cables on a gt 6 speed that r located at the top of the engine in back.. Do not touch the rear cable unless ur tibrron is shifted hard. The front cable is ur drift idle, theyre 2 nuts tightend den to secure it at a certian level , untighten the nuts and simply ajust the 2 nuts backwards do the cable isnt so tight and allows the engine to drop idle wen accelerater isnt pressed. Then do the same to the rear cable(2nd) cable untill u have ur tibron sounding just right..only sol_tion

Nov 03, 2012 | 2003 Hyundai Tiburon

1 Answer

How to locate purge flow valve


If you are getting computer codes on this, one way to validate that this is the sensor is to disconnect the fuel vapor line (look on the firewall for a plastic hose going into rubber fittings). Then plug the line with a firm fitting screw-driver (or similar). Start the engine - if your computer doesn't report any issues (no check engine light), then you probably have a problem with the purge valve solenoid. Mine appears to be on the firewall below the brake booster - I had to pull the tray for the battery to get to it comfortably...

Jul 02, 2012 | 2003 Dodge Neon

1 Answer

Location of the Purge Control Valve for 1998 Hyundai Tiburon


The correct "Hyundai" term for the valve that's attached to the Vapor Canister is the "Canister Control Valve".Why don't you try to clean the old one first. They get clogged with little bits of charcoal from the canister. It's simple so see if it's bad, take it off, and try to blow through the canister side with no electric going through. You shouldn't be able to blow because the valve is supposed to be closed. If you can blow it's because the valve is clogged and hanging open. If it is clogged, you might try and clean it.

Then take the hose off from the canister and clean the hose too, you'll get a handful of charcoal out before your done. If you don't clean the hose out, you'll probably clog the valve again, even if it's new.

That's why they usually change the canister and the valve at the same time. It gets clogged because you fill the tank to the max, it floods the canister with gas, and the charcoal floats up through the hose to the valve.

Jul 11, 2009 | 2003 Hyundai Tiburon

1 Answer

Location of Purge Control Valve on 2003 Hyundai Tiburon GT


Go to http://www.hmaservice.com/ and register (vehicle by VIN). Afterward, you'll have access to technical information (manuals, wiring diagrams, service bulletins, etc) about your vehicle.

Jun 09, 2009 | 2003 Hyundai Tiburon

1 Answer

Location of the Purge Control Valve for 2003 Hyundai Tiburon


There were two different engines which were installed in the 2003 Tiberon... the 2.0 liter 4 cylinder:
22c99c7.jpg

And the 2.7 Liter V6:
cb31feb.jpg

Jun 06, 2009 | 2003 Hyundai Tiburon

1 Answer

Code error P0441


this code refers to EVAP Emission Control System Incorrect Purge Flow, it can be tricky to diagnose because of the number of parts, I would first check the vacuum hoses between the purge valve and the air cleaner, then the purge valve and the canister, also check the fuel tank vent and fuel cap valve and gasket. any one of these can cause this check engine code. after checking this I would reset the computer and see if it comes back.

Apr 13, 2009 | 2004 Hyundai Tiburon

Not finding what you are looking for?
2003 Hyundai Tiburon Logo

Related Topics:

736 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...