Question about 1997 Lincoln Continental

1 Answer

I would like to know where the plug for the computer connection diagnostic is located thanks Helm

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Lincoln Master
  • 6,927 Answers

Under about your knees when sitting in drivers seat under dash get in floor board and look up

Posted on Jul 03, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the engine computer connection to connect the code reader?

The OBD diagnostic link connector (where you plug it in) is located Under hood, passenger side, upper firewall, mounted beside A/C evaporator housing on firewall. I hope this helped and good luck.

Feb 25, 2011 | 1993 Ford Explorer Limited

1 Answer

Cant connect diagnostic computer in port and get accurate reading on check engine and where is eic fuse located

eic located in main fuse box is under the hood in main fuse box,lift lid off and location will be diagram on inside of can reset that light by disconnecting positive cable from battery for 10mins. that will reset your whole computer. thank you for choosing

Dec 30, 2010 | 2005 Ford F-150

1 Answer

Have 2001 ford losing power on take off changed filter checked plug no codes changed maf but nothing fixing it very interminent any suggestions before i wast money on pump tooooooooooo

I would suggest,if you have no knowledge of your vehicles systems,you not change anymore parts.
If your going to do your own diagnostics,purchase the factory manuals and especially the Powertrain Control/Emissions Manual,from

Aug 31, 2010 | 2004 Ford F150

2 Answers

I have a 1994 daihatsu rocky 1.6L efi and want to know where you plug into the computer for a diagnostic test

There is a diagnostic cable which you will require to do the diagnostic test.
There is no need to physically replace chips, connect extra wires, or adjust hardware. Just connect one end of the cable to your computer's RS232 port and the other end to your daihatsu 14-pin Consult port, which is normally located near the fuse box. 

  • Do I need to have my car running while performing diagnostics?
    Most functions require only the ignition to be turned on, not the engine.
  • I'm not a professional mechanic, can I still use this cable and software?
    Yes. This cable and software are designed to be user friendly and easy to understand.
And for getting cable .You can get it from Autozone service centers.

Thanks. Keep updated for any more query. You can rate this solution and show your appreciation.

Jul 12, 2010 | Daihatsu Rocky Cars & Trucks

1 Answer

01 Sportage, had to put in heli coil in #2 spark plug, replaced all plugs, both coils and plug wires. Car is still misfiring. Is it possible that the computer or one of the sensors is damaged? Where is ECM...

could be the mass air meter the idle air control motor afuel injector i have replaced many on the sportages but the ecm is under carpet by the firewall on passenger floor you actually rest your feet above it in the pass side

Jul 29, 2009 | 2001 Kia Sportage

1 Answer

Where is the reset button exactlly located in a 1989 chrysler new yorker

Many of the engine/electronic computer systems are reset by disconnecting the battery (negative side first, usually) and allowing time for the voltage in the computer to bleed off ( 30 min).
Some require a connection (either a jumper or a diagnostics computer) to be plugged in.

Mar 24, 2009 | 1989 Chrysler New Yorker

1 Answer

Cannot find where to plug 16 pin diagnostic controller

graham, the only 99 civic engine available in the US is the 1.6 L, so this might not help u, but the 1,6 is the traditional location : driver side, under dash, driver side of steering column, behind lower dash panel. To make things interesting, isn't your steering on the right ? (ours is left). Guess u have to check both sides? Let me know if this is any help, if not , I'll try again!

Nov 25, 2008 | 1999 Honda Civic

4 Answers

Nissan ga15 engine idle adjustment locations

The idle speed is computer controled, it is not adjustable, you most likely have sludge in the throttle valve and the idle speed control air bypass valve, clean them with carb spray with the engine running.

Sep 17, 2008 | 1996 Nissan Sentra

2 Answers

Turning of oil service light on OBD II

My recommendation is definitely in the certified sevis because if you make a wrong conection wires can spoil the main computer

Jun 25, 2008 | 1996 BMW 318

1 Answer

Cam shaft sensor

It should be at the rear of the head at the end of the camshaft. some are located at the front of the head. Either one, there is a 2 prong plug that goes to it.

Jun 11, 2008 | 2001 Mazda 626

Not finding what you are looking for?
1997 Lincoln Continental Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts


Level 3 Expert

80339 Answers


Level 3 Expert

5687 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides