Question about 2005 Ford F 350 Super Duty

1 Answer

Turn signal fuse on 05 f250 diesel

No turn signals,turn signal fuse on 05 f250 diesel where is it also ac quit are they related

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I need repair fuse on f250 diesel

Posted on Nov 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 Ford f250 brake lights and turn signals won't work - checked all fuses, flasher and bulbs and all are good, what could problem be??


Well the brake light and turn signal circuits are on two different fuses, but they both go thru the turn signal switch.
So I would start by checking for power in and out of the turn signal switch for each circuit.

Apr 07, 2013 | 1990 Ford F250

1 Answer

Turn signal fuse 2002 ford f250... where is the fuse located


There are two fuses, a 20amp marked F2-13 and a 10amp marked F2-23. They are in the central fuse box which I think is under the speedometer.
Your owners manual will have the details.

Feb 28, 2013 | 2002 Ford F250 Super Duty SuperCab

1 Answer

2004 ford f250 xlt dual cab 7.3 4wd diesel turn indicators not working left hand side hazzard lights working. all visible fuse ok as are the relays


I would suspect the turn signal switch, turn the left turn signals on and grab the knob for the hazard switch and tug and push on it, if they start to work, the turn signal switch is bad.

Nov 19, 2010 | Ford F-250 Cars & Trucks

1 Answer

Have a 2008 f250 diesel I have no turn signal or brake lights on a trailer but running lights work ? The brake lights and signal lights work on truck . I don't have my owners manuel . What is the fuse...


CHECK THE FUSES IN THE BATTERY JUNCTION BOX # F34 25 AMP CARTRIDGE TYPE FUSE FOR TRAILER STOP/TURN RELAY
ALSO CHECK #33 IN THE SMARTJUNCTION BOX IF THE BRAKE CONTROLLER ISN'T WORKING

HOPE THIS HELPS

Aug 08, 2010 | 2008 Ford F 250 Super Duty 4WD

1 Answer

2005 f 350 diesel fuses?


its problem  is most likely the jem module located under the dash on pass side of the truck these can be expensive so be prepared  its been problem with ford diesels for  number of years 

Feb 16, 2009 | 2005 Ford F 350 Super Duty

1 Answer

Electrical System Problems in '02 F250 Diesel


Does the truck have daytime driving lights ? Sounds like a short , maybe the switch inside the steering column . Turn signal , wiper , headlamp dimmer ,or multifuction switch . Without testing this is just a guess . Find a wiring diagram at http://www.bbbind.com/free_tsb.html there free , get yourself a DVOM - digital volt ohm meter an test the B+ volt into an out of the switch . moving dimmer from low to high an turning on the turn signals etc.... Suggest you watch a few videos on youtube for automotive electrical testing , how to use a wiring diagram etc.... disconnect circuits at the mutifunction switch .

Measure the resistance between multifunction switch C202a pin 44, circuit 44 (LB), harness side, and electronic flasher connector pin 1, circuit 44 (LB), harness side; and between multifunction switch C202a pin 44, circuit 44 (LB), harness side, and ground.
  • Is the resistance less than 5 ohms between the multifunction switch and the electronic flasher, and greater than 10,000 ohms between the multifunction switch and ground?

Carry out the multifunction switch component test; Refer to Wiring Diagrams Cell 149 for schematic and connector information.
.

  • Is the multifunction switch OK?
Yes INSTALL a new electronic flasher. TEST the system for normal operation.

No INSTALL a new multifunction switch; REFER to Section 211-05 . TEST the system for normal operation.
Testing the electrical circuits of all the system not functioning properly is how you go about finding the problem .

  1. Visually inspect the following for obvious signs of mechanical and electrical damage.

    Visual Inspection Chart Mechanical Electrical
    • Headlamp switch
    • Multifunction switch
    • Battery junction box (BJB) fuse 3 (30A)
    • Central junction box (CJB) fuse:
      • 5 (15A)
      • 16 (20A)
      • 26 (10A)
      • 28 (10A)
    • Wiring harness
    • Loose or corroded connections
    • Headlamp relay (if equipped)
    • DRL relay No. 2 (if equipped)
    • DRL jumper (if equipped)
    • RAP module (if equipped)
    • Central security module (if equipped)
    • Light sensor amplifier (if equipped)
    • Headlamp bulb
  1. If the concern is not visually evident, determine the symptom and proceed to the Symptom Chart.

Symptom Chart
NOTE: Refer to the Wiring Diagrams for connector numbers stated in the pinpoint test.
Symptom Chart Condition Possible Sources Action
  • Both headlamps are inoperative
  • Battery junction box (BJB) fuse 3 (30A).
  • Headlamp switch.
  • Circuitry.
  • Multifunction switch.
  • GO to Pinpoint Test A .
  • The low beams are inoperative
  • Central junction box (CJB).
  • Circuitry.
  • GO to Pinpoint Test B .
  • The high beams are inoperative
  • CJB fuse 16 (20A).
  • Circuitry.
  • CJB.
  • Multifunction switch.
  • GO to Pinpoint Test C .
  • One low beam headlamp is inoperative
  • CJB fuses:
    • 28 (10A) (LH).
    • 26 (10A) (RH).
  • Headlamp bulb.
  • Circuitry.
  • GO to Pinpoint Test D .
  • One high beam headlamp is inoperative
  • Headlamp bulb.
  • Circuitry.
  • GO to Pinpoint Test E .
  • The headlamps are on continuously
  • Headlamp switch.
  • Circuitry.
  • Multifunction switch.
  • Daytime running lamp (DRL) relay No. 2 (if equipped).
  • DRL jumper (if equipped).
  • Headlamp relay (if equipped).
  • Remote anti-theft personality (RAP) module (if equipped).
  • Central security module (if equipped)
  • Light sensor amplifier (if equipped).
  • GO to Pinpoint Test F .
  • The high and low beam headlamp is inoperative on one side
  • Circuitry.
  • REPAIR circuit 57 (BK). TEST the system for normal operation.
  • The flash-to-pass feature is inoperative
  • Multifunction switch.
  • CHECK circuit 196 (DB/OG) for an open. REPAIR if necessary. If OK, INSTALL a new multifunction switch; REFER to Section 211-05 . TEST the system for normal operation.

Mar 07, 2017 | 2002 Ford F250 Super Duty SuperCab

1 Answer

Signals/hazards


there is two seperate relays for right and left trun singals, they are located under the hood in the relay box. i would start there this is a fuse that powers them both, in the same relay box

Dec 18, 2008 | 2002 Ford F250 Super Duty SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

759 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...