Question about 2001 Ford Focus

1 Answer

Grinding 1 to 2 gear/ ford focus. only when it heats up to normal operating temp. Wont grind if i wait for RPM to lower under 1000

Posted by on

  • jgrish485 Jul 03, 2009

    does that mean a new trani?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

It may be a faulty syncro.

Posted on Jul 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When stopped gears sometime grind when shifting into 1st gear(2001 Ford Focus)


Then the clutch is not releasing properly & the continual
grinding will wear the gear teeth & you may also have worn
syncros, that will require you to pull the trans & go thru it, as well
as do a clutch replacement

Mar 09, 2014 | 2001 Ford Focus

1 Answer

Ford focus gear hard to change


Hi there, if you say hard to change, does the gears grind if you change or does the shifter just feel stiff on changing???if the gears grind the clutch need checking, check the fluid level as well as it could be low, could only need to be adjusted if a cable model, most are hydraulic clutches so need to check the fluid.

Sep 22, 2010 | 2005 Ford Focus

1 Answer

Ford focus 2001. rear window drops down and wont go back up, motor working, any ideas, grinding noise when operated


I presume there is a slippage in the drive of the window winder. Open carefully the window flaps, first of all look carefully as you press for the motor to function. when the grinding noise come on, slowly life up the base of the glass support to see if it is holding. If this works open out the mechanism, check the cords/ reel/ gear for fault and replace. Hope you get this right. Try with patience / caution. Hope my advice works . Good day

Jul 02, 2010 | 2001 Ford Focus

1 Answer

My for galaxy started to grind a bit when i put it in first gear is it the clutch or the gear box going


Hi my name is Tom and I am here to help.

I am afraid it is your gear that are grinding. If it were your clutch, you would loose power and the clutch would ride high.

I would suggest the gear box get immediate attention. The problem will not go away. As you grind the metal coming off 1st gear will begin to "take out" the other gears.

I trust this info was of help. If I can be of further help let me know.

TomE

Jul 01, 2010 | 2001 Ford Focus

1 Answer

2000 Ford Focus Sputtering / Speedometer Needle Jump


Only 1000-2000 RPM? Does it do that in any gear?

Jun 20, 2009 | 2000 Ford Focus

1 Answer

2000 Focus grinding into 3rd


Sounds like you have solved it as far as the bad synchro. For these to be replaced the transmission basically has to be rebuilt in short or long form to get to the snychro to replace it.

For the right technician it is just a matter of doing it.

May 31, 2009 | 2000 Ford Focus

1 Answer

Tranny wont shift into fifth gear.


you could retry bleed clutch slave cylinder,should really replace these when replacing clutch if high mileage or it might be fifth gear ring gear broken or worn looking at gearbox strip or new gearbox i would try rebleeding clutch might have small airlock in it.

Dec 15, 2008 | 2000 Ford Focus

1 Answer

Gearbox wont stay in reverse


strip and repair job is only soloution the selector is worn or the gear its self is cream crackered

Nov 19, 2008 | 2000 Ford Focus

Not finding what you are looking for?
2001 Ford Focus Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...