Question about 2005 Peugeot 405

1 Answer

Drivers seat adjustmen not working, ratchet mechanism appears not to be working, not the runners

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Peugeot Master
  • 22,133 Answers

Give it a good oil with some engine oil in a proper oil can not that spray stuff

Posted on Nov 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do u fix a front seat seat belt retractor that is jammed inside the front right side of a 2006 trailblazer??


Some times you can't. However, using a long thin screwdriver and inserting it into the ratchet assembly you may be able to move the ratchet mechanism to release it. Look for any debris or a twist in the belt that may be causing the assembly to jamb

Aug 29, 2015 | 2006 Chevrolet Trailblazer

1 Answer

How do you remove the drivers seat in a '98 Jetta? I want to replace it. Thanks


slide the seat right forwards and you will see, inside the runners,the bolts to remove,the runners,with the seat...after the rears slide the seat right back to see the front bolts.replacement is a reversal of removal......

Oct 30, 2010 | 1998 Volkswagen Jetta

1 Answer

My drivers seat is stuck in a too forward position in my 2002 volkswagen passat


lift both sides of the bar under the seat,if that dont work,then take out the seat,with runners,and check whats fouling the ratchet bar.

Sep 04, 2010 | 2002 Volkswagen Passat

1 Answer

I need diagram and directions to change the ratchet on the drivers seat in a 1996 ford bronco. the bottom frame is broken and need to take it apart to weld the frame as you can not find a decent seat to...


Follow these steps to easily remove the driver's seat from ford bronco 1) Lean under the seat and unclip the harness that connects the seat belt sensor to the seat. You may need to use a small flathead screwdriver to pull the release open. 2)Attach the Mac Tools SC620B socket to the 3/8-inch ratchet and unbolt the seat from the floor. 3)Attach the 3/8-inch ratchet to the extension and then the socket. Unbolt the two bolts towards the center of the vehicle. These may be difficult to remove from the channel, but they will eventually come out. Then lift the seat out of the vehicle. 4) Now if you want to replace only ratchet then remove the ratchet from the seat and place new ratchet and reverse the procedure.
This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya

Mar 24, 2010 | 1996 Ford Bronco

1 Answer

Need seat wiring diagram for 96 blazer


here is the seat diagram SEAT

Hope it helps

Mar 30, 2009 | 1996 Chevrolet Blazer

3 Answers

2001 Chevrolet Tahoe - Power seat


The most likely cause is the switch, replace it.

Sep 22, 2008 | 2001 Chevrolet Tahoe

1 Answer

Drivers seat in Suzuki Vitara 2006


You will have to de-trim the seat back to access the mechanism.

Sep 02, 2008 | Suzuki Vitara Cars & Trucks

1 Answer

Seat Belt will not retract on 98 Pre Runner


When you replaced the belt did you make sure that the position of the belt assembly was the same. A slight misaliengment can affect the return mechanism. Pull the full length of the belt from belt coil Slacken the securing bolt moving the assembly will most likely allow the return of the belt.
If it was an old unit perhaps a drop of WD40 will release the mechanism.
Hope this helps
Mic

Jun 09, 2008 | 1998 Toyota Tacoma

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Wahs Team

Level 2 Expert

205 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...