Question about 1997 Ford Expedition

1 Answer

My Lock buttons are inoperative and my back-up lights do not work

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

The driver side door locks and unlocks all the doors in the car it could be that is malfunctioning and u need to replace the bulbs for the back up lights if that does not work then u need to check the fuses that supply power to them

Posted on Jul 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Is there a fuse or module for the shift lock?


could be but as i can remember its a manual button that you depress to release gear lever.
if it does have a fuse it will be under interior or center console fuse. try swopping it to test if thats the problem

Oct 27, 2016 | Cars & Trucks

1 Answer

How do I replace dash light bulbs on a 2007 Ford Escape?


What lights are not working ? The instrument cluster illumination is inoperative or all the lights ,radio , heater control head, all the switches that would be back lighted.
  • The climate control panel illumination is inoperative , The passenger door lock control switch illumination is inoperative. Could need new dimmer switch , new instrument cluster. When installing a new instrument cluster, it is necessary to upload the module configuration to the scan tool. Following installation of the new instrument cluster, download the module configuration from the scan tool into the new instrument cluster. Refer to Section 418-01 .
  • Dec 09, 2014 | 2007 Ford Escape

    1 Answer

    Ford ka liftgate light switch


    check that it is not in the lock itself

    Jun 11, 2013 | Cars & Trucks

    1 Answer

    I have 2 problems with my 2006 plate mitsubishi colt 1.1. Firstly the engine light just came on and I was wondering what could cause it and secondly the remote central locking only unlocks the passenger...


    The check engine light is a seperate issue from the inop. drivers door lock.A check engine light comes on after the PCM recognizes an input from any of the engines sensors 3 Key cycles or reading cycles while it is monitoring engines sensors.It could be as simple as an oxy.sensor out of spec to a low fuel tank pressure reading when you forget to put the gas cap back on after filling your tank.You need to have the car "scanned" for diagnostic trouble codes for the answer to the Check engine light". As for the inop. drivers door lock,it sounds like the lock solenoid stopped working and needs a replacement.Dealer,repair shop,or auto parts store can supply that fix.

    Oct 10, 2012 | Cars & Trucks

    1 Answer

    After battery replacement keyless entry stop working


    Synchronization
    When
    Key buttons operated repeatedly while vehicle out of range and system becomes inoperative. Key batteries replaced.
    How - early models
    Depress lock or unlock button. Manually lock and unlock driver's door within 30 seconds. System should operate normally after approximately 1 minute. If not, carry out programming procedure.
    How - late models
    If vehicle locked, manually unlock driver's door using key. Press key unlock button once. Switch ignition ON and OFF. Remove key from ignition switch. Press key lock or unlock button once. System should now operate correctly.

    Jun 24, 2010 | 2007 Audi A4 Convertible

    1 Answer

    2003 audi a4 had dead battery, charged battery and now the key fob won't work and the security lights flash for about 5 min everytime I do anything to the car. why ?


    Synchronization
    When
    Key buttons operated repeatedly while vehicle out of range and system becomes inoperative. Key batteries replaced.
    How - early models
    Depress lock or unlock button. Manually lock and unlock driver's door within 30 seconds. System should operate normally after approximately 1 minute. If not, carry out programming procedure.
    How - late models
    If vehicle locked, manually unlock driver's door using key. Press key unlock button once. Switch ignition ON and OFF. Remove key from ignition switch. Press key lock or unlock button once. System should now operate correctly.

    Apr 12, 2010 | 2003 Audi A4 Cabriolet

    1 Answer

    Door lock not working on the drivers side. 1999 Ford Explorer. Need wiring diagram and how to remove the parts.


    Visual Inspection Chart Mechanical Electrical
    • Binding latches
    • Door lock cylinder
    • Misaligned door
    • Lock actuator
    • Fuse
    • Relays
    • Switch
    • Wiring harness
    • Loose or corroded connections
    Symptom Chart Condition Possible Sources Action
    • The door lock is inoperative
    • Circuitry.
    • Power door lock actuator (218A42).
    • GO to Pinpoint Test A .
    PINPOINT TEST A: THE DOOR LOCK IS INOPERATIVE CONDITIONS DETAILS/RESULTS/ACTIONS A1 CHECK THE OPERATION OF THE SUSPECT DOOR LOCK sxn~us~en~file=box1.gif~gen~ref.gifCheck for binding or stuck conditions by manually operating the inoperative door lock.
    • Is the lock stuck or binding?
    sxn~us~en~file=arrow.gif~gen~ref.gifYes REPAIR or REPLACE the binding components. TEST the system for normal operation.
    sxn~us~en~file=arrow.gif~gen~ref.gifNo GO to A2 . A2 CHECK THE POWER DOOR LOCK ACTUATOR FOR LOCK OPERATION — CIRCUIT 117 (PK/BK) sxn~us~en~file=box1.gif~gen~ref.gif
    sxn~us~en~file=ic0004.gif~gen~ref.gif Inoperative Power Door Lock Actuator
    sxn~us~en~file=box2.gif~gen~ref.gif
    sxn~us~en~file=gn0085a.gif~gen~ref.gif sxn~us~en~file=box2.gif~gen~ref.gifMeasure the voltage at the inoperative power door lock actuator connector Pin 1, Circuit 117 (PK/BK), and ground while operating the door lock switch to the LOCK position.
    • Is the voltage greater than 10 volts?
    sxn~us~en~file=arrow.gif~gen~ref.gifYes GO to A3 .
    sxn~us~en~file=arrow.gif~gen~ref.gifNo REPAIR Circuit 117 (PK/BK). TEST the system for normal operation. A3 CHECK THE POWER DOOR LOCK ACTUATOR FOR UNLOCK OPERATION — CIRCUIT 118 (PK/O)/163 (R/O) sxn~us~en~file=box1.gif~gen~ref.gif
    sxn~us~en~file=gn0086a.gif~gen~ref.gif sxn~us~en~file=box1.gif~gen~ref.gifMeasure the voltage at the inoperative power door lock actuator connector Pin 2, Circuit 118 (PK/O) or 163 R/O, and ground while operating the door lock switch to the UNLOCK position.
    • Is the voltage greater than 10 volts?
    sxn~us~en~file=arrow.gif~gen~ref.gifYes INSTALL a new power door lock actuator. TEST the system for normal operation.
    sxn~us~en~file=arrow.gif~gen~ref.gifNo REPAIR Circuit 118 (PK/O) and/or 163 (R/O). TEST the system for normal operation.

    Mar 10, 2010 | 1999 Ford Explorer

    1 Answer

    My pontiac grand prix will not shift out of park


    do the brake lights work? if not the park lock out solenoid will be inop and will not pull lock out pin back to release park. let me know.

    Aug 05, 2009 | 2000 Pontiac Grand Prix

    3 Answers

    The back-up lights don't come on in reverse and the lock/unlock buttons are inoperative


    check fuse #5 15 amp red for back up lights.

    check fuse #3, 30 amp in box under hood for door locks.

    Jul 03, 2009 | 1997 Ford Expedition

    2 Answers

    Hazard button and door lock button not working 325i 02


    Your vehicle only has fuses behind the glove box. But since your central lock button is also inop. The your solution is to replace the switch assembly, it comes with both the hazard switch and the lock/unlock button. The removal of the switch assembly is pretty simple. it just pops up with some plastic body tool to pry on it.

    Apr 01, 2009 | 2002 BMW 3 Series

    Not finding what you are looking for?
    1997 Ford Expedition Logo

    43 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    75744 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    fordexpert

    Level 3 Expert

    5495 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...