Question about 2001 Ford Ranger Regular Cab

Open Question

2001 ford ranger 3.0 flex fuel. Code 1318 and how

2001 ford ranger 3.0 flex fuel. Code 1318 and how to fix it

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: Flex Fuel sensor Truoble Code

If your flex fuel sensor is bad there is a product on the market that is a much better alternative compared to purchasing a new sensor for over $600 or even a used one for typically around $300. The product is called a Flex Fuel Sensor Replicator made by T&S Electronics and can be purchased off their website www.tandselectronics.com. The cost of the Replicator is $150 and it is very simple to install. In fact, your old flex fuel sensor stays in place so you don't have to mess with your fuel line. The wiring from the original flex fuel sensor is hooked up to the Replicator which sends an electronic signal to your engine control unit that "replicates" the signal the ECU would get from the original FFS when you are burning standard unleaded gasoline containing up to 10% ethenol.

The only limitation present with the Replicator installed is that you can no longer burn E85 or other alternate fuels (no big deal for most people). And, as an advantage you should see a 1-2 mpg improvement with the Replicator installed.

Check out www.tandselectronics.com for more information or contact us via e-mail at support@tandselectronics.com.

Posted on Oct 08, 2008

Ad
  • 10 Answers

SOURCE: Code P0457

was the CEL on and fuel cap light on before you had the fuel pump replaced? if it was after the repairs were performed, double check all evaporative emissions lines, hose, and connection on and around the fuel tank. also make the the fuel filler neck is properly seated and clamped to fuel tank. if all good, check the plastic fuel filler top (just behind fuel door, where you put fueling nozzle) make sure it is not chipped or cracked anywhere. especially where the rubber seal from the cap rides.

Posted on May 07, 2009

jbass706
  • 167 Answers

SOURCE: how to fix obd2 code 1443 on 96 ford ranger emisson test failed

It is usually carbon pieces from the evap carbon canister clogging the purge solenoid and purge flow sensor. There should still be a one piece purge solenoid and purge sensor with hose assembly available. You will also need to replace the carbon storage canister.
After replacement disconnect the negative battery cable, hold your foot on the brake pedal for 30 seconds, then reconnect the battery.

Posted on Oct 25, 2009

  • 834 Answers

SOURCE: looking for a reset fuel reset button on a 2001

The fuel shut-off or Inertia Switch will either be located behind the passenger side kick panel, or it will be located behind the passenger side carpet just under the heater case.



4a37d3b.jpg

b037b38.jpg

Posted on Sep 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I swap my engine on my 03 ranger 3.0 flex fuel,with one from a 02 ranger gas fuel. It was running rough until I put my old fuel rail and injectors.But I still have a miss on cylinder #3 already install new...


Check compression in number three. You could have bought a bad engine. And yes. You need to change every sensor. If they don't match with the plugs. replace the engine. There is a reason for different engine codes. You should have stuck with them.

Jul 25, 2015 | Cars & Trucks

1 Answer

What are the top most common causes for the injectors on a 2001 ford ranger to not fire/mis-fire


1. Fuel (ethanol) clogging
2. Sensor (crankshaft or camshaft) mis-communication...bad sensor or signal to computer
3. Electrical harness (age cracking, corrosion)
4. Fuel filter clogged, not sending proper fuel pressure
5. Fuel pressure too low (fuel pump)

Not necessarily in order...but start with fuel, move to electrical inspection, then sensor...unless you have a CEL code to start with first.

Apr 08, 2015 | 2001 Ford Ranger

1 Answer

2003 ford ranger 3.0 flex fuel is getting a p0340 and p1336 code


http://www.therangerstation.com/tech_library/camshaft_position_sensor.shtml

Apr 15, 2014 | 2003 Ford Ranger Regular Cab

1 Answer

2000 ford ranger 3.0 flex fuel , engine is not getting fuel


The fuel pump only comes on for 3 to 5 seconds when key is turned on ,if it sees no #1 cylinder recognition

Don't want to load the cylinders with fuel & hydraulic the motor, if
you have no spark

Mar 04, 2013 | 2000 Ford Ranger SuperCab

1 Answer

2000 ford ranger po code 176 flex fuel sensor how to fix


DO NOT USE THIS COMPANY http://www.pointaengineering.com/main.sc Because they are a fraudulent company! The sensor they provide does absolutly nothing. I tried it and nothing changed in the way my vehicle ran.

Read more: http://wiki.answers.com/Q/How_do_you_install_a_flex_fuel_sensor#ixzz1xffNDp9W

Apr 05, 2012 | 2000 Ford Ranger SuperCab

1 Answer

I removed 3 relays from my ford ranger 2001 6 cilinders 3.ol and know idont know what is the fuel pump relay.can you help me how to know what is the fuel pump


they are listed in your owner manual. or go to motorcraft.com, procenter, tech info, owner manual.

fuel pump relay is 46A

4 relays in bottom left corner. it is lower right of the 4.

Dec 27, 2010 | 2001 Ford Ranger Regular Cab

1 Answer

2003 Ford Ranger Extended Can 3.0L V-6 Flex Fuel Automatic Transmission. I put a new motor in my little truck and now the transmission acts like its in neutral. I just found out the transmission is...


How do I change the 2003 Ford Ranger XLT 3.0 L Flex Fuel -Auto Trans 2wd Camshaft synchronizer and sensor . Do I need any special tools ? Are there after market parts that are precise replacements for the OEM parts ?

Aug 07, 2009 | Ford Ranger Cars & Trucks

1 Answer

My 2003 ford ranger quits running. i get a code p0176. fuel compensation sensor circuit malfunction. where is it and how do i fix it?


If your flex fuel sensor is bad there is a product on the market that is a much better alternative compared to purchasing a new sensor for over $600 or even a used one for typically around $300. The product is called a Flex Fuel Sensor Replicator made by T&S Electronics and can be purchased off their website www.tandselectronics.com. The cost of the Replicator is $150 and it is very simple to install. In fact, your old flex fuel sensor stays in place so you don't have to mess with your fuel line. The wiring from the original flex fuel sensor is hooked up to the Replicator which sends an electronic signal to your engine control unit that "replicates" the signal the ECU would get from the original FFS when you are burning standard unleaded gasoline containing up to 10% ethenol.

The only limitation present with the Replicator installed is that you can no longer burn E85 or other alternate fuels (no big deal for most people). And, as an advantage you should see a 1-2 mpg improvement with the Replicator installed.

Check out www.tandselectronics.com for more information or contact us via e-mail at support@tandselectronics.com.

Aug 12, 2008 | 2000 Ford Taurus

Not finding what you are looking for?
2001 Ford Ranger Regular Cab Logo

Related Topics:

197 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

84027 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22483 Answers

gerry bissi

Level 3 Expert

4387 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...