Question about 1998 Ford Windstar

1 Answer

98 windstar replaced fuel pump still won t start

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Expert
  • 4,070 Answers

U may need some fuel tank cleaning, rust may be clogging the fuel line thats why the fuel cant get thru, change the fuel filters too. hope this helps

Posted on Jul 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I put a new fuel pump in a 98 ford windstar it wont kick on


check the fuel pump relay it the possible cause or the fuse

Aug 09, 2012 | 1998 Ford Windstar

1 Answer

Occasionally my 98 chevy P/U won't start. The fuel pump does not run. If I fool around with the Ignition switch I eventually get the fuel pump to run, then it will start and run fine.


The fuel pump only comes on for 2 seconds when the ignition switch is turned on until it starts.I would check the fuel pressure it should be 60-66 psi with key on engine off.Sounds like a weak fuel pump to me you'll know once you check the pressure.If its not within specs replace pump.

May 10, 2011 | Chevrolet 1500 Cars & Trucks

1 Answer

98 windstar, 3.0 v6. shakes when in park, D,R etc. up to 30 moh ish. checked motor mounts, compression. balence bar turns, crank sensory mod., flex plate not cracked, master air flow sensor, cam sensor,...


SOUND LIKE WEAK FUEL PUMP.YOUR VECHICLE IS SURGING WHEN FUEL PUMP GOING BAD.REPLACE FUEL FILTER.CHECK FUEL PRESSURE SHOULD BE 35 - 45 PSI WITH KEY ON ENGINE OFF.IF FUEL SYSTEM OKAY. YOU COULD HAVE BAD SPARK PLUGS AND WIRES.

Dec 04, 2010 | 1998 Ford Windstar

2 Answers

Ford windstar 98 gl 3.8


would have thought so ,but it could have an electronic overload sensor though ,

Mar 11, 2010 | 1998 Ford Windstar

1 Answer

Hard start when hot 98 ford windstar with 3.8


Try replacing the fuel filter also Has it had a tune up? they need to have the plugs replaced at 100,000 if the fuel filter does not work then the most probable cause is the fuel pump is losing pressure when hot. The pump warms up and the check valve fails to close all the way allowing a now fuel or fuel starvation.

Sep 27, 2009 | 2003 Ford Windstar

1 Answer

98 Windstar fuel pump relay.


Relay is located under the hood in the power box. Under the power box lid shows where the relay is

Aug 31, 2009 | 1998 Ford Windstar

2 Answers

98 F.Windstar replace power steering pump but still hard to steer


rack and-or pinion... Good thing the 98 is a very good and popular windstar, its not as bad as it sounds.

Aug 16, 2009 | 1998 Ford Windstar

1 Answer

I have a '98 Windstar, replaced fuel filter and pump.


Most fuel pump relay units are located under the dashboard near the steering column. In some cases, the unit is located in the area where the steering column is mounted, or near the engine's firewall. Lift the carpet in the front section of the passenger or driver's side footwell to locate the wooden floor board; the end of the fuel pump relay is typically located near the center of the board

Jul 03, 2009 | 1998 Ford Windstar

1 Answer

Remove fuel pump from tank ford windstar 98


To gain access to the fuel pump, it is necessary to remove the fuel tank.
  1. Depressurize the fuel system and remove the fuel tank from the vehicle.
  2. Remove any dirt that has accumulated around the fuel pump module attaching flange, to prevent it from entering the tank during service.
  3. Turn the fuel pump module locking ring counterclockwise using a locking ring removal tool or a brass drift and remove the locking ring.
  4. Remove the fuel pump module.
  5. Remove the seal gasket and discard it.

To install:
  1. Put a light coating of grease on a new seal ring to hold it in place during assembly. Install it in fuel tank ring groove.
  2. Insert the fuel pump module into the fuel tank, then secure it in place with the locking ring. Tighten the ring until secure.
  3. Install the tank in the vehicle.
  4. Install a minimum of 10 gallons of fuel and check for leaks.
  5. Install a pressure gauge on the throttle body valve and turn the ignition ON for 3 seconds. Turn the key OFF , then repeat the key cycle five to ten times until the pressure gauge shows at least 30 psi.
  6. Check for fuel leaks at the fittings.
  7. Remove the pressure gauge.
  8. Start the engine and check for fuel leaks.

May 26, 2009 | 1998 Ford Windstar

1 Answer

98 ford windstar stalling when warm


have your catalytic converter checked sounds like its clogged. good luck to ya

Nov 17, 2008 | 1998 Ford Windstar

Not finding what you are looking for?
1998 Ford Windstar Logo

Related Topics:

217 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...