Question about 1997 Nissan Quest

2 Answers

Acceleration/engine stopping The engine just stopped while I was driving , after about 10 minutes i was able to start it but I drove to my destination without the airconditioning running. Later during the trip, I had an intermittent accelaration problem. I brought the car the nextday I arrived to my destinationI to a nissan service center and told me they have found cylinder misfire, knocked sensor, worn out spark plugs and cables.They replaced them including distributor cap and rotor. They also cleaned the throttle plate, checked timing. When I was driving back home, I had an acceleration problem again and then later the engine stopped. Restarted engine and continued driving but the whole trip was having this acceleration problem. I would like to know the real problem of my Quest. Thank you

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 784 Answers

They did the right things. Those are the first attempts to address the issue. However the issue is not resolved, please have them to check the ECU. When this is faulty, it gives the misfires or poor acceleration due to the wrong gas/ air mixture controlled by ECU. This is an expensive replacement . Make sure they can diagnose correctly.

Posted on Jul 03, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 158 Answers

You could be having a throttle position sensor going out or either the mass air flow may have debris in it. It could also be a problem with the fuel delivery (fuel pump/filter), or either an exhaust restriction/blockage.

Posted on Jul 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1992 pajero auto temp light stuck on when motor wasn't running long when accelerating vehicle stopped then hard to start now won't start at all,


Sir if the starter is not even turning im sorry to inform your engine might be broken. Lack of oil could be the reason. I d reccomend to send to a mechanic shop inmediately.

Jul 12, 2014 | 1995 Mitsubishi Montero

3 Answers

The car will run fine for about 10 minutes then it will stop accelerating???


ENGINE HESITATES WHILE ACCELERATION

LOSS OF ACCELERATION


It can be fuel pressure issue or it's the problem with accelerator pedal or its clogged filters causing there.

There are many other possibilities. I suggest you to go through the list of help links mentioned below, these will help you to confirm where the actual fault lies: -------

Jerks and Hesitates During Acceleration?

http://technoanswers.blogspot.in/2012/07/2004-dodge-town-country-jerks-and.html

-----------

Loss of acceleration?

http://technoanswers.blogspot.in/2012/02/loss-of-acceleration.html

---------

Headlights flickering and car hesitates to start?

http://howtobyme.blogspot.in/2012/02/headlights-flickering-and-car-hesitates.html

--------

How exactly the Vehicles Accelerator Cable works?

http://repairhelpcenter.blogspot.com/2011/11/how-exactly-vehicles-accelerator-cable.html

-------------

How exactly Vehicles Accelerator Pump Diaphragm Works?

http://repairhelpcenter.blogspot.com/2011/11/how-exactly-vehicles-accelerator-pump.html

--------

2000 Toyota Avalon: Engine Lean Codes and Knock Sound on Acceleration?

http://whatisbyme.blogspot.in/2012/05/2000-toyota-avalon-engine-lean-codes.html

---------

2004 Toyota Avensis: Acceleration And Deceleration makes noise on Front End?

http://whatisbyme.blogspot.in/2012/05/2004-toyota-avensis-acceleration-and.html

---------

Wheel hop under hard acceleration?

http://technoanswers.blogspot.in/2012/04/wheel-hop-under-hard-acceleration.html

--------

2009 Chevy impala accelerator pedal sensor?

http://technoanswers.blogspot.in/2012/02/2009-chevy-impala-accelerator-pedal.html

---------

Nissan Pathfinder stalls and bucks on Acceleration?

http://technoanswers.blogspot.in/2012/02/nissan-pathfinder-stalls-and-bucks-on.html

--------

Acceleration lag problem?

http://repairhelpcenter.blogspot.com/2012/01/acceleration-lag-problem.html

-------------

These details will help.

Thanks.

Nov 28, 2012 | 1999 Mercury Cougar

1 Answer

Car stopped accelerating. now it won't start


2 possible causes either fuel pump has broke cheeck for fuel under hood disconnect line and save gas in a clear container for 2nd cause water in fuel /not likely but possibley gas station had fuel del'y and wrong product was drop in to tanks cheeck to see if they have had a pump off since you fueled theire.

Nov 14, 2011 | 2008 Nissan Versa

1 Answer

Engine quit when stopped at stop light. Acted as if it was choking then died. Tried restarting. Turns over strong, no start. Thought maybe no gas. Added gas after about 30 minutes. Started first try....


Sounds like the fuel pump is going out. Replace the filter first, as it's only $10. If that doesn't fix it, then it's probably the pump, which is $250.

Jun 10, 2011 | 1993 Jeep Grand Cherokee

1 Answer

Just purchased a 94 Sunbird SE for my son (today) Started fine. Drove for 15 minutes. Shut it down and it sat for 1 hr. Started again after registration and insurance. Drove for 10 minutes. Stopped once...


Take it back to where you got it and make them refund your purchase price. If they refuse and you finianced it go to them, There a law called "The Lemon Law" that makes it unlawful to sell something like that. Sounds like you sure bought one. Don't do anything to it just get hold of the place where you bought it and tell them to come get their junk out of your yard! dhgill1949

May 22, 2011 | 1994 Pontiac Sunbird

1 Answer

Obd2 system rediness status won't clear so I can run the smog test due to replacing the battery.


takes a long time to run the rediness test since there are 6 different tests to complete...

PROCEDURE 1
EVAPORATIVE EMISSION SYSTEM LEAK MONITOR
Inspection Conditions
Engine coolant temperature: 30°C (75°F) or less (The engine is stopped before the test drive is started).
Atmospheric temperature: 5 - 30°C (41 - 113°F).
Condition of A/T: Selector lever D range.
Fuel remained in fuel tank: 30 - 50% is recommended.
Time required: 16 minutes or less after started the engine.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position. Well be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 16 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position.

PROCEDURE 2
FUEL TRIM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: -10 - 60°C (14 - 140°F).
Condition of A/T: Selector lever D range.
Time required: 30 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 30 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 3
CATALYTIC CONVERTER MONITOR
Drive Cycle Pattern
Inspection Conditions
Atmospheric temperature: -10°C (14°F) or more.
Condition of A/T: Selector lever D range.
Engine coolant temperature: Not set.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
Travel for 300 seconds or more while keeping the vehicle speed at 89 km/h (55 mph) or more.
Decelerate until the vehicle speed is within 80 km/h (50 mph) or less.
While traveling at 56 - 80 km/h (35 - 50 mph) for 10 minutes or more, fully close the throttle at least once in 2 minutes and decelerate for 10 seconds or more.
Do not repeat deceleration too often.
Vehicle speed may go below 56 km/h (35 mph) after the deceleration.
Stopping and braking are permitted. (If stopped or drive at 56 km/h (35 mph) or less for more than 5 minutes the monitoring may be stopped. In this case please restart monitoring from the beginning.)
After completing the above deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 5 times.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 4
HEATED OXYGEN SENSOR MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or more.
Atmospheric temperature: -10°C - 60°C (14 - 140°F) or more.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 - 80 km/h (35 - 50 mph) and travel for 16 minutes or more.
Stopping and braking during this operation are permitted. Keep the accelerator opening degree constant for 1 minute or more after each acceleration.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 5
EXHAUST GAS RECIRCULATION (EGR) SYSTEM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: 5 - 60°C (41 - 140°F).
A/C switch: OFF.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While traveling 16 minutes or more at 56 - 80 km/h (35 - 50 mph) with engine speed 2,000 r/min or above, fully close the throttle at decelerate for 5 seconds or more until the engine speed reaches 1,000 r/min or under.
Do not repeat deceleration too often.
Stopping and braking are permitted (Rapid deceleration and sharp steering are not permitted).
After completing the deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 8 times by fully closing the throttle valve.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 6
OTHER MONITOR (Main Components, Sensors & Switches, Wire Breakage & Short Circuit)
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature:
100°C (212°F) or less (Except engine coolant temperature sensor monitoring).
30°C (86°F) or less (Engine coolant temperature sensor monitoring).
Atmospheric temperature:
5°C (41°F) or more (Except engine coolant temperature sensor monitoring).
-10°C (14°F) or less (Engine coolant temperature sensor monitoring).
Condition of A/T: Selector lever D range.
Time required: 21 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start
Accelerate until the vehicle speed is 56 km/h (35 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 km/h (35 mph) or more and travel for 16 minutes or more.
Return the vehicle to the shop.
After stopping the vehicle, continue idling for 5 minutes, and then turn the ignition switch to the "LOCK" (OFF) position. Moreover, the vehicle should be set to the following conditions for idling.
A/C switch: OFF
Lights and all accessories: OFF
Transmission: Neutral

Sep 15, 2010 | 1998 Mitsubishi Eclipse

1 Answer

I just replaced my tranny. It was working great


About 3 months ago, during my 25-mile commute to the ambulance base where I volunteer, my transmission started acting up. After a few minutes of driving normally, it started to upshift very hard. Each upshift was accompanied by a noticeable "Bang!" and it felt like the car was hitting a pot hole.

I immediately stopped and checked the tranny fluid at a service station, but the fluid level was fine and it didn't have any burnt smell. The car has 76K miles on it and the transmission fluid was changed at 50K per the maintenance schedule. I had no choice but to continue on to the base, driving very gently.

I made a stop about 5 minutes before arriving, to pick up dry cleaning. I was in the cleaners for about 8 minutes, and when I came out the hard shifting had completely disappeared. The car drove smoothly for the next 3 months.

Now, this problem seems to recur any time I drive the car even remotely hard. We're not talking about full-throttle accelerations here, since my everyday driving stays below 2500 RPM to save on gas. But if I'm in a hurry and start driving a touch harder - crossing over 3500 RPM - then the tranny will start shifting hard within minutes. Let it sit for 10 minutes with the engine off, and the problem is gone again

Oct 02, 2009 | 1995 Oldsmobile Cutlass Supreme

1 Answer

'99 Chevy Cavalier


If this only happened AFTER you drove through the water, I'd say it had to do with the water. When ignition parts get wet, they short out and lose performance. Once they heat up and dry out, they will be back to normal. If you haven't had a tune-up in a while, I suggest you get one. Ignition wires are usually the first to give you problems when they get wet. Sometimes if it's really damp outside, you can have the same issue you did when you drove through the water.

Aug 14, 2008 | 1999 Chevrolet Cavalier

Not finding what you are looking for?
1997 Nissan Quest Logo

339 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...