Question about 2005 Saturn Relay

Open Question

How to replace turn signal bulb on saturn 2005 relay

Can't get teh headlamp out to get at teh turn signal. I followed the owners manual and removed the headlamp retainer and screw but the assembly wont pull out.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: 2005 saab 9-3 linear headlamp assembly

which bulb?

Posted on Sep 18, 2008

  • 1 Answer

SOURCE: Headlamp assembly on Pontiac G6

well there isn't much on gripping the retainers, what they are, are plastic ball and socket clips. I would lay some tape down underneth the lamp onto the bumper to protect the bumper and then the hard part...while making sure the headlamp is above the bumper, pull with some force on the back half of the light to where it meets with the fender, after a little pulling it should (no promises) should come out, it will seem like it will break but it shouldn't. (I use to work at a body shop and did many of those headlights including my own '06 G6.) Hope that helps.

Posted on Dec 31, 2008

rtpflh
  • 546 Answers

SOURCE: Side Marker Bulbs

you need to remove entire assembly to access bulbs.it is secured by small hex head screws & a ''sliding tab'',an L shaped piece you pry up w/a flat screwdriver.

Posted on Sep 20, 2009

  • 401 Answers

SOURCE: How do I remove the PS headlight assembly on a 2005 Montana

ok you have removed the bolt and the retaining pin
now pull the light foward to disengage the ball and socket attachment at the rear of the headlamp

Posted on Feb 13, 2010

  • 869 Answers

SOURCE: where can I buy a headlamp bulb retainer clip for

to buy spare parts of ur BMW pls visit amazon or ebay.

Posted on Jan 16, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace marker light


Removal Procedure
  1. Open the hood.
  2. Remove the headlamp. Refer to Headlamp Bulb Replacement .
  3. Rotate the bulb and socket counterclockwise in order to remove the bulb and socket from the housing. Remove the side marker bulb (3) or turn signal/park bulb (4) from the socket.

Oct 01, 2015 | 2005 GMC Envoy

2 Answers

Replacing front right turn signal bulb


what are the ways u tried....
open the bonnet, nw u can find an access to the front right lighting assembly.... u can change the bulb nw 

reply back

Jun 15, 2008 | 2007 GMC Yukon Denali

1 Answer

HOW TO REMOVE A HEADLIGHT FROM A 2007 SATURN OUTLOOK XE


Hi Carol , your going to have to remove the headlamp assembly to replace the bulb !


Remove the headlamp assembly. Refer to Headlamp Replacement.



1



Headlamp Bulb Accessory Covers (Qty: 2)



2



Headlamp Bulb Assembly (High Beam)




Caution: Refer to Halogen Bulb Caution in the Preface section.




Tip

Disconnect the electrical connectors and remove the bulbs.



3



Headlamp Bulb Assembly (Low Beam)


Callout

Component Name

Preliminary Procedure

Remove the front bumper fascia. Refer to Front Bumper Fascia Replacement .




Headlamp Assembly Bolt (Qty: 4)

Notice: Refer to Fastener Notice in the Preface section.

Tighten

6 N?·m (53 lb in)







2





Headlamp Fascia Brace Fender Reinforcement Bolt




Tighten

6 N?·m (53 lb in)







3





Headlamp Cam Adjuster




Procedure

Set the headlamp adjusters at the nominal setting of 6 turns off fully seated.







4





Headlamp Cam Locking Nut







5





Headlamp Assembly




Tip

Disconnect the electrical harness as the headlamp assembly is being removed from the vehicle.

Apr 08, 2015 | 2007 Saturn Outlook XE

1 Answer

Replace rear signal light on driver side


Open the rear hatch, remove the screws that hold the rear taillight assembly to the vehicle. Find the socket for the bulb you need to replace and turn it counter clockwise. Remove the socket, then replace the bulb. Installation is the reverse.

Feb 10, 2014 | 2005 Saturn Relay

1 Answer

Replace turn signal bulb


The procedure to replace the REAR turn signal light bulb is as follows:- 1) There are three wing nuts on the inside of the trunk for each tail light. 2) Remove the piece of plastic just inside the trunk where the latch is. 3)Then remove the two thumb screws that the cargo net is attached to and the piece can be pulled up. 4)Them pull the carpeting away from the area where the tail light is located. 5)properly remove the three thumb screws. 6) Keep the bulb handy so you can fit the new bulb as the old bulb is removed out. The procedure to replace the FRONT turn signal is as follows:-- 1) First remove the front headlight assembly.And the bulbs . 2) Open the hood to remove the headlight assembly. 3) Pull the headlamp assembly straight out from the vehicle (moving the headlamp up and down slightly may help to remove it easily). 4) Front turn signal is located below the headlamp assembly (turn/parking lamp on top and the fog lamp is below it). 5) Then turn the bulb socket 1/4 turn counterclockwise to remove it from assembly. 6)Then pull the old bulb from the socket and replace it with a new one. Thanks. you can rate this solution and show your appreciation.

May 21, 2010 | 2005 Pontiac Grand Prix

1 Answer

Change headlinght bulb


SECTION 417-01: Exterior Lighting 2005 Freestyle/Five Hundred/Montego Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/14/2005 Headlamp Bulb adobe.gif Printable View (327 KB) Freestyle, Five Hundredn0035265.gif
Item Part Number Description 1 — Headlamp bulb electrical connector (part of 14290) 2 13N021 Headlamp bulb

Montegon0035266.gif
Item Part Number Description 1 — Headlamp bulb access cover screws (6 required) (part of 13006) 2 13N019 Headlamp bulb access cover 3 — Spring retainer (part of 13006) 4 13N021 High intensity discharge (HID) bulb 5 14A411 HID bulb electrical harness 6 — High beam bulb electrical connector (part of 13006) 7 13N021 High beam bulb Removal and Installation
ani_caut.gif WARNING: The headlamp bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Avoid touching the glass envelope. Failure to follow these instructions may result in personal injury.
NOTE: The headlamp bulb should not be removed from the headlamp assembly until just before a new bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp assembly where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed from the headlamp assembly.
NOTE: Make sure the headlamp switch and ignition switch are in the OFF position.
Freestyle, Five Hundred
  1. Rotate the headlamp bulb 1/8-turn counterclockwise and remove the headlamp bulb.
    • Disconnect the electrical connector.
Montego
  1. Remove the headlamp assembly. For additional information, refer to Headlamp Assembly — Five Hundred, Montego in this section.
  1. Remove the 6 screws and the headlamp bulb access cover.
Montego high beam bulb
  1. Rotate the headlamp bulb 1/8-turn counterclockwise and remove the headlamp bulb.
    • Disconnect the electrical connector.
Montego HID bulb
  1. Release the spring retainer and remove the HID bulb.
    • Disconnect the electrical connector.
All vehicles
  1. To install, reverse the removal procedure.

2010&c18=modelyear&c20=n920901&c35=wsm%2cheadlamp%20bulb%2cs5f%2c417-01%2cremoval%20and%20installation&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=582&ct=lan&hp=n&[aqe]

Apr 02, 2010 | 2005 Ford Five Hundred

1 Answer

Please tell me how to replace a burned out head light, high beam.


To replace the headlamp, turn signal, or parking lamp bulb:This information should be in your owner's manual.
Turn the wheel to access the wheel well.
  1. Remove the fasteners located on the wheel liner. To access the headlamp and the turn signal/parking lamp bulbs.
  2. Reach in behind the wheel well liner and locate the bulb to be changed.
  3. Turn the bulb socket counterclockwise and pull it straight out of the lamp assembly.
  4. Pull the old bulb straight out of the bulb socket.
  5. Push the new bulb straight into the bulb socket until it clicks.
  6. Push the bulb socket straight into the lamp assembly and turn it clockwise to lock it into place.
  7. Reinstall the wheel well liner using fasteners.

Nov 11, 2009 | 2006 Chevrolet HHR

1 Answer

How do i change the front right turn signal bulb?


OPEN THE HOOD THE SCREWS TO THIS UNIT IS BEHIND THE UNIT ,SOMETIMES ALL YOU NEED TO DO IS REACH BEHIND TWIST THE BULB OUT AND REPLACE,IF NOT THEN NEED TO REMOVE THE UNIT TO GET TO THE BULB

Oct 29, 2009 | 2005 Saturn Relay

1 Answer

I need to change a dead bulb in my headlights and I dont have the owner manual.


96 sable, only ino I have. should be similar. Please rate, thanks

  1. sth~us~en~file=ani_caut.gif~gen~ref.gif WARNING: THE REPLACEABLE HALOGEN HEADLAMP BULB CONTAINS GAS UNDER PRESSURE. THE HALOGEN HEADLAMP BULB MAY SHATTER IF THE GLASS ENVELOPE IS SCRATCHED OR THE HALOGEN HEADLAMP BULB IS DROPPED. HANDLE HALOGEN HEADLAMP BULB CAREFULLY. GRASP HALOGEN HEADLAMP BULB ONLY BY ITS PLASTIC BASE. AVOID TOUCHING GLASS ENVELOPE. KEEP HALOGEN HEADLAMP BULB OUT OF REACH OF CHILDREN.
    NOTE: A properly aimed headlamp (13008) assembly normally need not be re-aimed after installation of bulb. A burned out headlamp bulb and retainer (13N021) should not be removed from the headlamp until just before a replacement headlamp bulb and retainer is to be installed. Removal of a headlamp bulb and retainer for an extended period of time may allow contaminants (dust, moisture, smoke) to enter the headlamp and affect the performance of the headlamp. When servicing the headlamp bulb and retainer, energize the headlamp bulb and retainer only while it is contained within the headlamp body.

    Make sure headlamp switch (11654) is in OFF position.
  1. NOTE: On some models the clamps holding the integrated relay control module (IRCM) may need to be unsnapped and the module pulled aside to gain access to the driver side bulb.

    Open hood and locate headlamp bulb through hole in upper radiator support assembly.
  1. Remove headlamp wire connector from headlamp bulb and retainer by pulling the connector and wires in a rearward direction.
  1. Remove headlamp bulb retainer (13N019) by rotating counterclockwise (when viewed from rear) about one-eighth turn and sliding headlamp bulb retainer off headlamp bulb and retainer. Keep headlamp bulb retainer as it will be used again to retain new headlamp bulb and retainer.
  1. Carefully remove headlamp bulb and retainer from opening in headlamp bulb (13007) by gently pulling straight out of opening. Do not rotate headlamp bulb and retainer during removal.
0a1a11c.gif

Jul 05, 2009 | 1991 Mercury Sable

Not finding what you are looking for?
2005 Saturn Relay Logo

Related Topics:

508 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...