Question about 1998 Nissan Altima

1 Answer

Stops light always on, i changed the break switch and my problems are still there. Thanks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Nissan Master
  • 1,348 Answers

Change the relay with another one that is the same part number.the relay may have fused together,and make sure the bulbs are the right ones,and then check the wiring in the trunk and make sure a ground wire is not squished or cut,shorting to ground.

Posted on Jul 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 2005 Crown Victoria .....Brake lights just stopped working (upper light also) All other functions work fine(hazards,turn signals & running lights) Just replaced the brake switch & there st


change the light control module. it is located under the dash near your right knee on the drivers side. this is a common problem with crown vics.

Feb 11, 2013 | 2005 Ford Crown Victoria

1 Answer

Jetta break light is on and when driving it beeps??


It might be the parking brake warning - you may need to check the parking brake switch.

Sep 03, 2012 | Volkswagen Jetta Cars & Trucks

2 Answers

My break lights don't work even after I changed the bulbs. I have a 1996 Plymoth Breeze.


First check the fuse(s). If fuse ok then I would check the brake pedal switch...these often pop off their mount or become misadjusted when under dash work has been done(eg:remote starter installed,stereo,etc..)

Dec 08, 2010 | 1996 Plymouth Breeze

1 Answer

After it stops, the car sit for about 2 hours or


Possible cause would be the coil breaking down. After the car starts and runs again and stops take a inline spark tester and connect between the coil and the spark plug wire to check for fire. If no fire then remove the coil and replace it. hope this will help you.

May 10, 2010 | 2001 Dodge Intrepid

1 Answer

RIGHT STOP LIGHT WORKS IRREGULARLY(2002 FORD WINDSTAR)


thereis three switches to check one is the muti function switch. the second is the headlight switch and third is the brake switch on the pedal.if not them check your ground and see if it is secured properly

Mar 07, 2009 | 2000 Ford Windstar

1 Answer

2000 blazer break lights stuck on


check the gruond in the black wire in the blinker switch if its ok, sometime the after market parts have ashort life time try to replace the flasher switch ( blinker switch)

Mar 07, 2009 | 2000 Chevrolet Blazer

4 Answers

Brake lights come on when i put foot on clutch Jaguar 2003 xtype


the brake switch is faulty or needing adjustment but not a big thing to change think i would just fit a new one 

Jan 02, 2009 | 2003 Jaguar X-Type

1 Answer

ALL BREAK LIGHTS NOT WORKING


Have you checked your brake light fuse? If it is good do your rear turn signals work? If you have turn signal and no brake lights it is probably the turn signal switch these are a common problem and your power for your brake lights goes through your turn signal switch. Sometimes it is actually the hazard switch that melts but this can not be serviced alone. If you have no rear turn signals and no break lights it could still be the turn signal switch but is more likely to be a wiring problem in the rear usually trailer wiring T connections. Chiltons has wiring diagrams in there manuals but they are not always accurate. Let me know if I can help you further and please rate.

Dec 27, 2008 | 2000 Chevrolet Blazer

1 Answer

The directional's do not work as well as the break lights. Changed bulbs in rear for brake lights. solution did not help. checked the switch at the break peddle. THEN the directional light stopped woring...


Occassionally, but not always I have no power to all the dashboard when switching the car on. Next time I start up they are back, any ideas where to look?

Jul 20, 2008 | 2003 Ford Focus

Not finding what you are looking for?
1998 Nissan Altima Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...