Question about 2004 GMC Sierra 2500
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: ABS problem with GMC 2002 Sierra
its a low speed abs activation the problem is in the front sensors they need to be cleaned or replaced they [or one] probably has some corrosion on the sensor --[the 99 chevy tahoes had a limited recall over this issue and the fix was to remove and clean the abs sensor or if to corroded replace ] this problem doesnt set off an abs code or trouble light also sometimes the abs will activate by itself at under 4 mph without even touching brake
Posted on May 15, 2010
Wheel speed sensors misadjusted, damaged , or metal shavings and other debree, since they are magnetic can give false readings from one of the wheel circuits. Over sized tires can give of false speed readings as well. there are many other causes including bad relay, control module, e.t.c. It is best to have the proper scan tool to diagnose an ABS problem
Posted on Jul 09, 2009
yo man, idk if this is exactly what your problem is but my 1991 gmc sierra was doing the same fuckin thing and ****, and i took it to the gm dealer and had them look at it and my connectors and my ignition switchs were fried, also my truck was having a problem shitfing once those went but i also had that problem, perhaps yours is somehwta liek that as well... hope i could help
Posted on Aug 08, 2009
remove cover.take off back wheels and calipers (or drums).turn differential to where you see small bolt/pin (5/16) horizontally (same direction as axles)on right side of differential.remove bolt/pin.A large pin (about 5"long 3/4"diameter) should slide out differential with ease ( you may have to tap one side of the large pin).turn differential to completely remove large pin.turn differential so you can see in the view window.push each axles in (they'll go in about 1 1/2"each) You may hear one of the axle C-clips fall.If not use a small telescoping magnet to remove the C-clips from the axles through the differential window.pull each axle out about 10"so they are out of the diff.Now remove the cap bolts(4-5/8"bolts) and remove the caps(mark the caps so they go in excactly the way they came out.be careful the diff might fall out.If not you may have to use a long bar or 2x4 to wedge and pry the differential out. Have a basket/crate w/rags in it to catch the diff.TIP:If you are removing the ring gear from the diff, the bolts are left handed bolts meaning you have to turn them clockwise to loosen and counter clockwise to tighten ; )
Posted on Sep 15, 2009
Testimonial: "thank you helped ALOT perfect instructions "
The switch or the wire harness at the blower motor has gone bad. The highest setting 5 has no resistor, so the blower runs on high but the high current flow ends up burning up the switch's contact on that setting or the resistor wire harness at the blower motor has gone bad. Common would be the switch it self, if the switch is good. Then it's going to be the wire leads at the speed resistor by the blower motor under the glove box by the passenger leg compartment. Keep me posted, be glad to help you get your Sierra running 100% again soon.
Posted on Jan 06, 2010
Tips for a great answer:
Sep 25, 2016 | 1995 GMC Sierra
Feb 11, 2015 | 2004 GMC Sierra
Jan 08, 2015 | 2004 GMC Sierra
Feb 12, 2013 | 2004 GMC Sierra Denali
Jul 13, 2012 | 2000 GMC New Sierra 1500
Sep 02, 2010 | 2004 GMC Sierra
May 15, 2010 | 2002 GMC Sierra
Nov 02, 2009 | 2000 GMC New Sierra 1500
Jul 31, 2009 | 1995 GMC Sierra C1500
Jul 08, 2009 | 2001 GMC Sierra Crew Cab
507 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: