Question about 1991 GMC Sonoma

1 Answer

I need a diagram of a proportioning valve that goes to the master cyclinder, i can't remember how to hook the lines back up to it. thanks mike

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 6,927 Answers

If it has a mount it should line up the line unless the lines have been bent around out of place if it doesnt mount ,,,most of the lines if not all should be differnt sizes

Posted on Jul 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Nissan Tiida 2007 model vehicle problem the abs kicks in but no light on the dash. It would kick in while stopping at a stop street or anywhere but intermittently. Brake discs/pads tyres replaced.


try bleeding lines, that can happen with air bubble in check valve, some check valves have a bleeder on them, if not set emergency break on rear it will push fluid back to master cyclinder, for front wheels collapes calipers to push fluid back. first look at mater cyclinder if tilted up you may need to lift front or back to level cyclinder before starting. Have used a baby nose cleaner to remove air bubble from master cyclinder be sure engage break padel when pulling fluid from master cyclinder

Sep 19, 2017 | Nissan Cars & Trucks

2 Answers

How to reset the proportioning valve in brake master cylinder for 1989 Ford F150?


to reset the proportioning valve try bleeding the master by applying pressure and slowly opening one line at the master until the valve centres. you may have to do the same with the other line to get it to centre, sometimes you have to hit the area where the valve is as it may be stuck to get it to move.

Sep 26, 2014 | 1989 Ford F 150

1 Answer

Location of back brake master cylinder on a 1985 Yamaha venture totaled 1200


can't find a diagram, I believe it is on the right side rear, there should be cover there, it is attached to the proportioning valve as I recall. hope that helps. Follow the front brake line back and you will find the Proportioning valve and you will find the other cylinder.

May 17, 2014 | Cars & Trucks

1 Answer

I need a break line diagram for 1995 ford countur


It doesn't connect to master cylinder. The line should connect to a proportioning valve, then from valve to master cylinder.Star at master cylinder and follow lines to proportioning valve.

May 25, 2010 | 1995 Ford Contour

2 Answers

'93 Cougar master cyclinder is leaking badly, OEM


There is an aftermarket available for $40-160. If you were to take it to a local shop instead of the dealer you could probably save alot of money.

Dec 23, 2009 | 1993 Mercury Cougar

1 Answer

Hooking up the brake lines to the master cyclinder


well that is easy the front line goes in the front and the raer to the rear

Mar 27, 2009 | 1993 Chevrolet Lumina

1 Answer

1998 bravada brake problem


If you have not replaced any brake lines or brake calipers, then It sounds like that the brake proportioning valve or the brake master cylinder if defective. If the the brake pedal goes to the floor, the master cylinder is at fault. If not, the proportion valve, which is part of the ABS valve body is defective. Have your local garage check these two components for possible problems.

Jan 11, 2009 | 1998 Oldsmobile Bravada

Not finding what you are looking for?
1991 GMC Sonoma Logo

Related Topics:

654 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...