Question about 2000 Dodge Intrepid

1 Answer

2000 intrepid a/c low pressure hose

The intrepid has a 3.2 from a 2000 concorde in it. i need a low pressure a/c hose but i can not find a match.a diagram of the proper hose would help thanks chuck

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 3 Answers

If you have a local dodge dealer ship you can ask them for a diagram and they will print it off there computer for free! here is a dealer ship that i got one from www.autotropolis.com/.../turnpike-chrysler-dodge-jeep-20648/

Posted on Jul 05, 2009

  • BAXTERSPRING Jul 05, 2009

    hope this is helpful!

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Detailed instructions needed to Replace rack and pinion on 2001 Chrysler Concorde


There's a three-part video on YouTube for doing this on a 2001 Intrepid - same car. See the link:
2001 Dodge Intrepid ES steering gear rack removal part 1

Mar 30, 2017 | 2001 Chrysler Concorde

1 Answer

Ac refrigerant hose from auto store does not match low pressure fitting


If your hose fitting is smaller than the fittings on the Tahoe, you just might have a hose that fitts the older R12 systems.

Jul 03, 2012 | Cars & Trucks

1 Answer

Need diagram or picture where the low pressure ac connection is


So you can add refrigerant to a leaking system
and polute the atmosphere?

Have it properly & safely done at a repair shop,
trained & licenced to do so, using the proper
equipment.

If you follow the suction hose to the compressor
& don't see the low side fitting,then it will be on
or near the compressor

May 23, 2011 | 2001 Mercury Grand Marquis

1 Answer

Low pressure power stering hose


It runs next to the high pressure hose from the pump to the reservoir. It's 3/4 inch hose, it's held on with clamps, unlike the high pressure hose that has compressed fittings. Your best bet is to remove the hose and match it up with a parts store.

May 06, 2010 | 1998 Volkswagen Jetta

1 Answer

Remove thermostat


300M, Concorde, Intrepid, LHS, 1998-2004
THERMOSTAT - Removal & Installation

2.7L Engine
  1. Disconnect negative cable.
    CAUTION Do not remove pressure cap with the system hot and under pressure because serious burns from coolant can occur.
  2. Drain cooling system.
  3. Remove radiator lower hose from thermostat housing.
  4. Remove nuts from heater tube flange studs.
  5. Loosen starter bolt at heater tube bracket.
  6. Pull heater tube out of thermostat housing and position out of the way.
  7. Remove bolt and two studs.
  8. Remove thermostat housing, O-ring and thermostat.
  9. Remove thermostat housing bolts.

To install:
  1. Clean gasket sealing surfaces.
    NOTE Install thermostat with the bleed valve located at the 12 o'clock position, between tabs on seal.
  2. Install thermostat and seal into thermostat housing .
  3. If removed, install two studs.
  4. Install thermostat, thermostat housing and O-ring and bolt. Tighten attaching bolts to 105 inch lbs.(12 Nm).
  5. Lubricate new heater return tube O-ring with coolant.
  6. Position heater return tube flange over two studs. Install nuts.
  7. Tighten retaining nuts to 53 inch lbs.(6 Nm).
  8. Tighten starter bolt to 40 ft. lbs. (54.3 Nm).
  9. Connect the lower radiator hose to the thermostat housing. Install hose clamps.
  10. Refill cooling system.
  11. Inspect for leaks.
  12. Connect negative cable.

3.2L & 3.5L Engines
  1. Disconnect negative cable.
    CAUTION Do not remove pressure cap with the system hot and under pressure because serious burns from coolant can occur.
  2. Drain cooling system.
  3. Raise vehicle on hoist.
  4. Disconnect electrical connectors from engine oil and power steering pressure switches.
  5. Disconnect radiator and heater hoses from thermostat housing.
  6. Remove thermostat housing bolts.
  7. Remove housing, thermostat, and gasket.
    NOTE The OEM thermostat is staked in place at the factory. To ensure proper seating of replacement thermostat, carefully remove the bulged metal from the thermostat housing using a suitable hand held grinder. It is not necessary to restake the replacement thermostat into the thermostat housing.

To install:
  1. Position gasket on thermostat and housing.
  2. Install thermostat housing, gasket and mounting bolts onto block. Tighten attaching bolts to 105 inch lbs. (12 Nm).
  3. Install radiator hose.
  4. Install bypass hose.
  5. Connect electrical connectors from engine oil and power steering pressure switches.
  6. Connect negative cable.
  7. Fill cooling system.
  8. Inspect for leaks.
  9. Lower vehicle on hoist.

Hope this help (remember comment and rated this).

Apr 04, 2010 | 2000 Chrysler Concorde

1 Answer

I need a second hand chrysler intrepid 2001 engine


these intrepids are dodges biggest mistake ever, the chances of you finding a good used motor to put in one are very slim to none, especially at a reasonable price, because unless you find an intrepid that was smashed up, just about everyone in the bone yard has a bad motor...a little secret that i just myself learned about a month ago when dealing with another shop, you can take a motor from a concord and with a few modifications get it into that intrepid the mods dont cost anyhing as long as you have the intrpid motor to pull parts from, its little things that dont line up like the heater hoses, just pull them off the intripid motor and put them on the concords, all the mount and other important areas line right up. It would be a learning experience but those concord motors are far more reliable than the intreid ones.

Mar 20, 2010 | 2001 Dodge Intrepid

1 Answer

I NEED TO REPLACE THE POWER STEERING PRESSURE SENSOR BUT I NEED A DIAGRAM OF WHERE IT WOULD BE ON A 99 CRHYSLER CONCORDE


Hi!
The power steering pressure switch is mounted in the pressure line between the steering gear and the steering pump.
Just follow the line from the pump and you'll find it.
Good luck

Feb 10, 2010 | 1999 Chrysler Concorde

1 Answer

Low freon on a 1998 chrysler concord, where is the low pressure l


low refrigerent in a concorde was USUALLY caused by a leaky evaorator a big job at best and best left to a pro

Mar 28, 2009 | 1998 Chrysler Concorde

1 Answer

Replacing power steering hoses - 2001 Concorde


you can but what are the price of the parts .just a pain to get at the fittings just make sure they are the right hoses and they are put back on the high pressure and low pressure sides .cut the old ones and tap a socket over the fitting rather then wrench might strip it and have troubles geting out and root them the same spot the old ones came from

Mar 03, 2009 | 2001 Chrysler Concorde

Not finding what you are looking for?
2000 Dodge Intrepid Logo

Related Topics:

274 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...