Question about 1999 Ford Expedition

1 Answer

Having problem replacing the driver side head light bulb.

I can not get my hands or figure out how to get the head light bulb in or out of the driver side for my '99 Ford Expedition. Can you Help?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 112 Answers

Look for stainless steel clips above the lamp assembly in the support frame around the radiator and grill. Lift these clips straight up to allow the lamp to tilt forward letting you reach behind it to un-clip the pigtail and turn the retainer ring counter clockwise. Pull the bulb straight out the rear of the lamp assembly, keep bare fingers and dirt off the new bulb glass and reverse the order of dis-assembly.

Posted on Jul 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003trailblazer head light bulb replace


Drivers side: Gotta stick your hand way in there in front of the battery, and take the rubber dust boot off, just slides right off. Twist the bulb out, and disconnect from connector.

Passenger side: easiest if you just remove the air cleaner box, 3 screws, one on the top, one on the right side, and one on the bottom left. Remove these screws, then pull box straight up. You'll then have complete easy access to the rubber dust boot and bulb.

Feb 10, 2016 | 2003 Chevrolet TrailBlazer

1 Answer

How to change head light bulb, drivers side, 2006 Saab 9-7X


Easiest way is to stick your hand in front of the battery and take the dust cover off, twist the bulb and done. I'm lucky, have smaller hands! lol, If you can't get to it, remove the battery for easy access.
The passenger side requires removal of the aircleaner box.

Mar 25, 2015 | 2006 Saab 9-7X

1 Answer

Low bean changing on 2008 touareg passenger side


LOOK IN SIDE BACK INDEX OF OWNERS MANUAL IN GLOVE COMPARTMENT.LOOK IN BACK INDEX FOR BULB REPLACEMENT IT WILL SHOW YOU HOW TO REPLACE HEAD LIGHT LOW BEAM BULB.DONT TOUCH HALOGEN WITH HANDS BECAUSE OILS FROM HANDS WILL CAUSE HALOGEN LIGHT BULB TO OVER HEAT AND BLOW OUT WEAR CLEAN GLOVES WHEN HANDLING BULBS.

Oct 16, 2011 | 2008 Volkswagen Touareg

1 Answer

Driver side low beam bulb replacement


LOOK INSIDE OWNERS MANUAL IN GLOVE COMPARTMENT.LOOK IN THE BACK INDEX FOR BULB REPLACEMENT.IT WILL SHOW AND TELL YOU HOW TO REPLACE BULB.BE SURE TO WEAR CLEAN LATEX GLOVES WHEN HANDLING HALOGEN HEAD LIGHT BULBS.BECAUSE OILS FROM FINGERS OR HANDS WILL CAUSE HALOGEN BULBS TO OVER HEAT AND BLOW OUT.

Jun 23, 2011 | 2007 Saab 9-3 Aero Convertible

1 Answer

How do you replace the license plate light bulbs on a 2002 Cadillac STS?


Hi there,

There are two bulb containers above the license plate light and you just need a small screw driver to press in under the left side of the plastic bulb housing to release the plastic clip. The plastic bulb holder will swing from the right hand side and will then fall out. All you need is a medium size flat head screw driver.

You have to unscrew the housings with a philips screw driver and take the housing out of the hole, by turning it sideways and pulling it out. Then turn out the bulb holder from the back of the housing and pull out the bulb.

Hope this helps...

Jan 24, 2011 | 2001 Chevrolet Blazer

1 Answer

Installed driver side headlight worked, an hour later both main headlights went out, when I went to check lights noticed that there was another headlight behind a little chrome cover that was out, could...


reasons bulbs keep blowning.your head light bulbs is halogen bulbs.dont touch with bare hands.the oils on your hands will make them over heat and blow.so use clean gloves on your hands when replacing the head light bulbs.if all is good.check alternator out put.it could be overcharging causing too much current flow through electrical circuit blowing out bulbs.use a digital volt meter hook it battery with car running battery voltage should be 13.5 to 14.5 volts. if it is 15 to 16 volts too many volts.alternator is faulty.due to lock out features turn off radio before disconnecting battery cables so you wont lose radio playing code.

Nov 24, 2009 | 2004 Honda Accord

1 Answer

How to replace our low beam headlight on 1999 town and country


1.) Open the hood of your van 2.) On the passenger side of the vehicle, look behind the headlight enclosure. You will see a set of wires running into the back of it. This is the power clip. Either with your hand or a flat-head screwdriver, pop the power clip off.
3.) There is a plastic ring encasing the light bulb. Turn the ring counter-clockwise and pull it out of the socket and set it aside.
4.) Pull firmly on the light bulb to remove it.
5.) Place the new light bulb into the same opening. Be careful not to touch the glass part of the new bulb. The oils in your skin can substantially reduce the life of the new bulb.
6.) Replace the plastic ring and turn it clockwise to lock it in place.
7.) Reattach the power clip to the back of the bulb.

Oct 29, 2009 | 1999 Chrysler Town & Country

2 Answers

Can't get passenger side marker light out on a 2007 kia spectra


There is one bolt on top of the radiator support and another in back. The assy fits into a pluug that keeps it aligned so it cam be tough to remove. Just wiggle it side to side while pulling and it'll slowly come out.

Are you looking to fix the bulb that is in the corner of the headlamp? You don't need to remove the head light for that. The is a black cap that screws off just beind it.

Sep 12, 2009 | 2007 Kia Spectra LX Sedan

1 Answer

Removing the head light from a 1997 pathfinder


I replace my head light bulbs recently and it was easy.
I think that you might have to replace the whole head light assembly in order to replace the glass.
Hope this helps. I found the answer in the drivers hand book under light bulb replacement.

Mar 12, 2009 | 1997 Nissan Pathfinder

3 Answers

Replace headlight for 2005 Chev Trailblazer


59Shadow.
Thank you for sharing the information on the light bulb. You just saved me money from having to take my 2003 Trailblazer in to have the low beam bulb replaced. I did exactly what you said.
1 Open hood and lock.
2. Take filter cover off (4 screws and they stay with the filter).
3. 3 inch cover pulls off.
4. Twist light bulb 1/8 turn.
5. Unclip the wiring harness to light bulb assembly.
6. Test by turning light switch on.
7. Align assembly with light housing and turn 1/8 until it snaps in.
8. Put 3 inch cover back on.
9. Place filter cover back on and hand tight the 4 screws.
10. Close hood.

Dec 12, 2008 | 2005 Chevrolet TrailBlazer

Not finding what you are looking for?
1999 Ford Expedition Logo

Related Topics:

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...