Question about 1993 Buick Park Avenue

1 Answer

Dent in oil pan need new oilpan where canI get one for 1993 buick

Dent in oil pan

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 52 Answers

How bad is the dent? If its only small then a whole new oil pan really isn't necessary I dont believe

Posted on Jul 02, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oil pan removel on 1998 jimmy wont come off motor. do i need to losen trans to get oil pan off


check that the bottom half of the timing chain cover isn't too tight, or the seals and gaskets are good and stuck, make sure you have a couple oilpan bolts threaded loosely enough to allow the oilpan to move but threaded enough to hold the oilpan up, hit the bottom of the oilpan to knock it loose

Sep 16, 2017 | 1998 GMC Jimmy

1 Answer

How do you change the oil pump in a 1995 chevy lumina 3100


You must remove the oil pan. I do not think you can do this with the engine in the car. If you can remvove the pan from the bottom without engine removal, it would be easy. Most every engine has to be removed to fully remove the oilpan. So my solution is- remove engine, remove oilpan, remove pump, replace pump, pan, and engine.

Dec 04, 2013 | Chevrolet Lumina APV Cars & Trucks

2 Answers

How do you remove the oil pan from a buick rendevous 2002. Have all bolts removed but oil pan is still up. How do you remove so you could take old gasket off and put new one on.


It's not uncommon for the oil pan to get stuck. This usually happens if the gasket was not put on correctly and gunk gummed up the seal, essentially gluing it in place. Use a small nylon, wood or leather covered hammer and tap around edge of pan. (use a lot of light taps to avoid denting the pan). Continue tapping until oil pan comes free. Don't try to pry off as this will deform the pan causing an uncontrollable oil leak.

Oct 27, 2010 | 2002 Buick Rendezvous

1 Answer

There's a big dent in my oil pan; it's not giving me an accurate reading on the stick. The stick says that it is over full by a quart when actually it is a quart low. and the pan also appears to leak. I...


I'm not sure the year and make of this car, but if its a newrer buick then its not to hrad to replace the oil pan, jack the front of car up and support it with jack stands, then remove the oil from pan. remove the bolts holding the pan, pan should drop down, you may have to tilt back and wiggle out, also you may have to drop the pump or pickup screen depending on how much room is needed to remove the pan.

Aug 16, 2010 | Buick LeSabre Cars & Trucks

1 Answer

I dented my oil pan and now rocker panel ticking.


if the oil pan is dented up to where it touches the oil pump the engine is not getting oil rockers are clacking . every time you start the engine you are damaging the bearings if they are not already gone you need to fix it right away drop the pan and bang out the dent with a hammer hope this helps

Aug 02, 2010 | 2005 Hyundai Santa Fe

1 Answer

I NEED TO KNOW THE TORQUE SPECS FOR THE OIL PAN ON A 1994 BUICK LESABRE 3.8 L. V6


Exploded view of the oil pan and related components - 1993 vehicle shown

48ac114.jpg


* If removed, install the oil pump pipe and screen. Secure with the retaining bolt(s) and tighten to 89 inch lbs. (10 Nm).

* Place a new formed rubber gasket in the oil pan flange.


* Position the oil pan and secure with the oil pan-to-engine bolts. Tighten the bolts to 124 inch lbs. (14 Nm). Do NOT overtighten the bolts, as this will damage the oil pan, causing a leak.


Hope help with this (remembere rated and comment this help).

Mar 08, 2010 | 1994 Buick LeSabre

1 Answer

1999 firebird 3.8L low oil pressure at idle only when hot


your oil pump does that on purpose - more noticeable with a dented oilpan as pressure is slightly increased. nothing to do until it goes (if it goes) unless you want to throw parts at your car anyways.

Aug 24, 2009 | 2000 Pontiac Firebird

1 Answer

How do I remove the oil pan on my 1991 Buick Century with a 3.3 V6 engine.


if theres a cross bar the engine will need to be removed.
if not just remove all the bolts around the oilpan and remove it.

Jun 12, 2009 | 1991 Buick Century

1 Answer

Oil pan leaking


1ST LOCATE THE SOURCE, JUST BECAUSE IT IS ON THE PAN DOES NOT MEAN THE PAN LEAKS, IT IS THE LOW SPOT SO ANY OIL ENDS UP THERE NO MATTER WHERE IT LEAKS FROM, HAVE THE ENGINE STEAM CLEANED AND THEN DRIVE IT UNTIL YOU SEE WHERE THE OILS SOURCE IS, THIS IS HOW WE DO IT AT THE DEALER.

Nov 03, 2008 | 1993 Buick LeSabre

Not finding what you are looking for?
1993 Buick Park Avenue Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

80417 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...