Question about 2003 Ford F150 Regular Cab

Open Question

How to check ignition module on a 92 ford ranger

Posted by on

  • yadayada
    yadayada May 11, 2010

    witrhout the ford only tester u can't

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chuck943
  • 783 Answers

SOURCE: where is the ignition module control located on 1996 ranger 2.3 e

It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.

Posted on Apr 08, 2009

seans46
  • 161 Answers

SOURCE: Location of GEM Module on 1998 Ranger

i am almost sure it is in steering col area by firewall. but call any part store like auto zone and they can print it out and tell you if your ford dealer wont. but on the fords they usualy are all in the drivers steering area sometimes way up by fire wall

Posted on Jun 15, 2009

  • 5501 Answers

SOURCE: 1991 ford ranger 3.0 eec relay fuse keeps blowing fuel good no sp

I understand that there is a relay box under the hood with 3 relays. Which is which I don't know. However if you are blowing the fuse TO the ecc relay, then the relay must be bad. This relay controls the spark.

Posted on Jul 25, 2009

roniecon
  • 6826 Answers

SOURCE: 1989 ford ranger 2.3l ignition control module

The coil is mounted on top of the module,I hope this was helpful,If so.please let us know.

Posted on Nov 22, 2009

  • 701 Answers

SOURCE: Where is my Ignition Control Module on 86 Ford

hello grizz_dipper: My name is Roger and I will answer for you. You will find the TFI (module) located on the distributor. Will be held on by two screws. If you are replacing this do to a spark problem I would suggest you replace the stator in the distributor also. The stator can short out the module. Also the module can short out the stator.
Should you need further help please just ask. Please rate the answer you received. This way i know it was helpful. Thank You for using Fix Ya. Roger

Posted on Jan 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1989 ford ranger location of ignition control module


Check for a Thick Film Integrated (TFI) Module attached to the outside of the distrfibutor with about an 8 wire plug on it. That is Ford's ignition module. My recollection is the two screws attaching it to the distributor are odd-ball 7/32 in. size. If the module is taken off, use special ford di-electric grease on the base before re-attaching. For heat dissipation.

Nov 19, 2012 | 1989 Ford Ranger

1 Answer

My 92 ford ranger sometimes acts like its not running on all four cylinders what could be the problem for this? I replaced plugs and wire and put two new ignition control modules in and didnt do a thi


sounds like the pick-up coil in the distributor. when pick-up coil goes bad they sometimes have intermittent electrical contact, therefore causing veh to run rough at times, and fine at some. it will eventually go out totally.

Aug 27, 2012 | 1992 Ford Ranger

1 Answer

What is the specific ignition control module number for a 4-cylinder, 2.3 liter Ford Ranger?


I recommened only the factory part for this. You can buy it from most full service part stores and not just the Ford dealer. The part is
MOTORCRAFT Part # DY959 [ICM] (Ignition control module) $176.79
You can also mail order it from a site I use called rockauto.com the price given above is from that site.

Feb 19, 2012 | 1992 Ford Ranger

1 Answer

My 94 ford ranger keeps blowing coil packs and im not sure what steps to take


have you replaced the ignition module...i am not sure when they started incorperating them inside pcm, so check to see if you have an ignition module

Aug 11, 2011 | 1994 Ford Ranger Supercab

1 Answer

1992 ford ranger will not crank- the starter will turn it over but never start. when i trung the key can hear the fuel pump turn on - added fuel still nothing . been a great truck since 92- what do i need...


Check for spark. No spark can be from the coil, igntion module, crank sensor. Have the codes check, this will at least point you in the right direction.

Feb 05, 2011 | 1992 Ford Ranger

1 Answer

I HAVE A 1993 FORD RANGER 3.0 V6 ENGINE AND NEED


For 1993 Ford Truck Ranger 4WD 3.0L MFI 6cyl the Control Module-Ignition is located under hood, center, rear engine area, mounted on distributor.

f2a2c92.jpg

Fig. 1: View of the remote mounted Ignition Control Module (ICM)

Hope this help (remember comment and rated this).

Jul 27, 2010 | 1993 Ford Ranger SuperCab

2 Answers

Where is the ignition control system located on a 1992 ford ranger?


the ignition module should be bolted to the side of the distributor. It takes a 5.5 millimeter socket or you can get a special tool at any good parts store. they should be able to check the module for you once you get it off.

Jan 16, 2010 | 1992 Ford Ranger

3 Answers

Where is the ignition module control located on 1996 ranger 2.3 e


It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.

Apr 08, 2009 | 1996 Ford Ranger SuperCab

Not finding what you are looking for?
2003 Ford F150 Regular Cab Logo

Related Topics:

328 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...