Question about 1992 Chevrolet Astro Extended

1 Answer

Turn signals and flashers work but not indicator light on dash one worked , i removed dash to replace bulb, now both don't work, bulbs are ok?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 2,200 Answers

Hi
There are 3 possible causes for this

1) The bulbs are defective.

2) The bulbs are not properly seated into the holders.

3) There is a defect in the actual circuit board.

In my experience these problems are mostly caused by the bulb not being properly seated into the bulb holder. These bulbs can be awkward to fit and it is important to ensure they are making a good contact to the terminals in the bulb holder itself.

In replacing the first bulb you may have dislodged the second bulb causing it to fail. Depending on the type of bulb used you sometimes need to bend the metal tabs on the bulb itself to force a good contact.

Feel free to post a further comment if you wish to clarify anything.

Posted on Jul 02, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a Chevrolet cobalt and the left turn signal will not work the inside light on dash flashes fast. I have changed the light bulb still doesn't work.


Fast flashing usually indicates that one of the exterior bulbs isn't functioning. You've checked front and rear signal lights, right? If the bulb is good, it could be corrosion in the socket, bad ground, broken wire, etc.

Oct 16, 2015 | 2006 Chevrolet Cobalt

2 Answers

My right front turn signal on my 2001 ford ranger doesnt work and my inside right turn signal light on dash doesnt work and flashes really fast. Buld on right side was replaced and works when lights


was the correct bulb used? this sounds like a single function bulb was used NOT the bulb that will light with the headlights and ALso produce turn singles

Dec 06, 2014 | 2001 Ford Ranger Regular Cab

2 Answers

Turn signal


check the individual indicater bulbs are all working ,actually look at each one not just the dash indicater light ,if all ok try the hazard switch if same happens the indicator relay needs changing if not the light/indicator switch will need replacing i would think good luck

Mar 19, 2014 | GMC Sierra Cars & Trucks

2 Answers

Tail lights not working


ck fuse for rear taillights tis under the dash lower left of steering wheel. or if you still have the manual look in there under fuses.
also look for a bad ground but i doubt that.. if it's both rear out.
fast flashing well here's a chart with all sorts of info.
Problem What To Do Turn signals light, but do not flash Replace the flasher No turn signals light on either side Check the fuse. Replace if defective.
Check the flasher by substitution.
Check for open circuit, short circuit or poor ground. Both turn signals on one side don't work Check for bad bulbs.
Check for bad ground In both housings. One turn signal light on one side doesn't work Check and/or replace bulb.
Check for corrosion in socket. Clean contacts.
Check for poor ground at socket. Turn signal flashes too fast or too slow Check any bulb on the side flashing too fast. A heavy-duty bulb is probably installed In place of a regular bulb
Check the bulb flashing too slow. A standard bulb was probably installed in place of a heavy-duty bulb
Check for loose connections or corrosion at the bulb socket Indicator lights don't work in either direction Check If the turn signals are working
Check the dash indicator lights
Check the flasher by substitution One Indicator light doesn't light On systems with 1 dash indicator:
- See if the lights work on the same side. Often the filaments have been reversed In systems combining stoplights with taillights and turn signals
- Check the flasher by substitution On systems with 2 Indicators:
- Check the bulbs on the same side
- Check the indicator light bulb
- Check the flasher by substitution
hope this helps. may want to print for future reference. :)
hope this helps.

Dec 31, 2017 | GMC Suburban Cars & Trucks

1 Answer

I need to find the flasher relay for a grand marquis 2001 .does it has one? My turn signals wont work I can hear the sound but don't even flash


Yes, it does have a flasher, although it may be a combined unit with the hazard flashers relay. So you hear the clicking of the flasher relay? That seems to indicate the relay is working properly. Have you checked the bulbs and the turn signal fuse? Any turn signal bulbs light up anywhere, front or back?
How about your brake lights, do they work? Your car may have separate, stand alone turn signals in the rear, but many American cars use the same bulb and same filament on the bulb for the brake lights and turn signals. If your merc is like this and the brake lights work, then the bulb must be good.
Turn on the hazard flashers and see if all bulbs work and flash at each corner of the car. This would be the same bulb as for the turn signals. If they work, it could be a bad turn signal switch, may even be the flasher relay somehow malfunctioning, and in a few cases, a bad hazard switch can affect the turn signal switch. Check fuses and bulbs first. If you have any type of body control module that controls lights and other accessories, you may have to investigate that. I know I'm not being very helpful, just throwing out a few suggestions. Good luck.

May 21, 2012 | 2001 Mercury Grand Marquis

3 Answers

I have a 1995 chevy cavalier and the turn signals just stay on and don't blink. I have changed the flasher and the multi function switch and still no luck


First, is it doing it on BOTH isdes or just on one side? Example: turn signnals flash OK when turning left, but only come on and stay on when turning right. If it is doing this, then you most likely have either a blown bulb or a bad bulb socket on the side that is not flashing. You need to check both the FRONT and REAR bulbs to make sure they are all functioning properly.
If it is doing it on BOTH sides, then you either have a bad flasher, or at least 2 bulbs burned out (one or more on each side).

Are you sure you replaced the correct flasher? The flasher for the HAZZARD lights is plugged into the convinience center under the left side of the dash. If this is the flasher you replaced, it is the wrong one.
The turn signal flasher is mounted to the driver's knee bolster bar near the steering column. It is held to the bar with a clip. (see diagram)

9_25_2011_3_20_38_pm.gif

Sep 25, 2011 | 1995 Chevrolet Cavalier

2 Answers

The turn singnals don't flash on my 2004 chevy impala


It's time to replace the flasher relay.The signal flasher is located under the dash near the steering column.Also check for the indicator bulb.Replace them if damaged.
Front Turn Signal Light Bulb Size: 3457ALL
Rear Turn Signal Light Bulb Size: 3057
Hope this helps.Your valuable feedback would be appreciated.Thanks

Jun 11, 2011 | 2004 Chevrolet Impala

1 Answer

The brake lights work but the turn signals don't!! Have checked the fuses and bulbs, but not finding the problem


Fuses and bulbs OK, but wires? Additionally I suggest keep in mind that turn signals work with FLASHER devices (two independent) on 1993 Buick Skylark..

Application: Turn signal
Flasher is located: Front seating area, driver side, under dash, driver side of steering column, mounted on support bracket

Application: Hazard flasher
Flasher is located: Front seating area, driver side, under dash, above kick panel, mounted in top of convenience panel

Hope this helps (remember to rate and comment this answer).

May 14, 2011 | 1993 Buick Skylark

1 Answer

Turn signal dosent work


you need to check to see which bulbs don`t work both front and back lights for the signal on the side it`s not working,you don`t say if any signals work or not if no signals work then you need to check the fuses under the dash on the driver`s side.now if it`s just one side then check the lights as mentioned above.if one isn`t then replace the bulb.if neither bulb is working then it sounds like the signal flasher is not working.turn on the hazard flashers and check the lights front and back.if all bulbs work then leave the hazards on and look under the dash for the flasher that is making the noise,this will show what the signal flasher will look like,then find the signal flasher on the fuse panel under the dash it should be located on the fuse panel.and replace

Mar 15, 2011 | 1997 Dodge Ram 1500 Club Cab

2 Answers

1992 Cadillac Brougham 5.0 L V8 RWD, turn signal don't work.


The turn signal switch is most likely the problem,but change the flasher for the turn signals first,some times this is all that it is.

Jun 11, 2010 | 1992 Cadillac Brougham

Not finding what you are looking for?
1992 Chevrolet Astro Extended Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...