Question about 2003 Mitsubishi Eclipse Spyder

1 Answer

EGR VALVE REPLACEMENT- I have the new part but there is not a gasket included. I assume a gasket would be necessary but I don't really know.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 61 Answers

Best way to tell is to pull out and see. If they dont give you one with it tho it most likely will not have one.

Posted on Jul 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

EGR valve Mazda 2002 V-6 Tribute replacement


25348714-wbcquewu0r2lyixgzwrhmelx-3-0.gif

  1. Remove the EGR valve.
  1. Disconnect the vacuum line.
  2. Disconnect the EGR tube.
  3. Remove the EGR valve and discard the gasket.
NOTE: The EGR valve sealing surfaces are soft metals.

  1. To install, reverse the removal procedure.
  1. Carefully clean all sealing surfaces and install a new EGR valve gasket.

Jan 01, 2015 | 2002 Mazda Tribute

1 Answer

The engine malfunction light turn on and brought it to the dealer. said P0406 and needs egr replacement. but the light turns off again and after a week it turns on again for 1 day. now the light is gone....


Sounds like you have a carbon buildup in the valve. The EGR should be located near the altenator on the right side of the engine, depending on what engine you have. 4 bolts, 2 8mm and 2 10mm.. take it off and careful not to lose the metal gaskets.. spray the valve down with carb cleaner and wipe it out.. pump the valve to make sure it plunges ok and replace. should fix your problem. Or you can replace the valve yourself new for about $80.
Here is the procedure if you care to do it yourself.

Tools: 8 mm socket, 10 mm socketEquipment: Replacement EGR Valve, Replacement EGR Gasket (metallic)1. Disconnect the electrical fitting attached to the EGR valve. You will need to unlock it (red tab) and then depress the latch near the rear of the fitting before sliding it off.2. Disconnect the vacuum tube connected to the top of the EGR valve using an 8 mm socket. It may be easier to remove the entire vacuum tube by diconnected it at the top of the engine as well (also 8 mm).3. Using a universal socket joint (I found using a 1/4" drive was necessary to get the clearances around the alternator), remove the 2 bolts holding the EGR valves to the exhaust manifold of the engine using a 10 mm socket. The bottom bolt is a very tight clearance.4. Remove the valve and gasket.5. To install, reverse the steps using the new EGR Valve and EGR Gasket.6. The 10 mm bolts should be torqued to 225 in-lbs7. The 8 mm bolts that fasten the vacuum tube to the EGR valve should be torqued to 100 in-lbs.
Tip: I have found that if you loosen the alternator mounting bolts, you can get just a little more wiggle room to get a socket on the bottom bolt.

Good luck, i hope this helps, please rate me a fixya.

Jun 28, 2011 | 2005 Dodge Caravan

1 Answer

EGR Flow problems


I am assuming that you vehicle is equipped with a 3.1L V-6 since you didn't mention it. (If this is not correct, please post a comment and let me know.)

You most likely have clogged-up EGR ports.
You will need an EGR-to-manifold gasket, a throttle-body base gasket, a wire coat hanger and a spray can of carb and choke cleaner.
EGR Valve gasket: FEL PRO part number 70804 - $5.99 at AutoZone
Throttle Body Base Gasket FEL PRO part number 61053 - $1.49

Remove the EGR valve and the throttle body. Cut the wire coat hanger so you have a piece about 8" long. Use the piece of wire to scrape and pick through the carbon buil-up in the port that goes between the EGR valve and the intake manifold. You can work from both ends by going at an angle through the hole in the manifold where the throttle body mounts and from the other side where the EGR valve mounts. Once you have broken through all the carbon, clean out as much as you can with the piece of wire.

NOTE: Try to not allow this stuff to go into the intake manifold area - engine valve damage can occur if this stuff gets stuck in a valve. It may be a good idea to stuff a rag in the intake just beyond the work area to catch the debris. - DON"T FORGET TO TAKE THE RAG BACK OUT BEFORE YOU RE-INSTALL THE THROTTLE BODY!

After most of the carbon is removed, spray the carb cleaner through the port to finish cleaning it out. After you are satisfied that it is as clean as it is going to get, reassemble the EGR and throttle body. Clear your fault codes and retest the vehicle.

This should do the trick.

Jun 16, 2011 | 2001 Chevrolet Lumina

1 Answer

Where do I find the EGR valve on a 1995 subaru Legacy 250T automatic


  1. Detach the vacuum hose from the EGR valve.
  2. Remove the two nuts which secure the EGR valve to the intake manifold assembly.
  3. Remove the valve and gasket from the manifold.
  4. Clean all gasket material from both mating surfaces.
  5. Check the vacuum hose for deterioration and replace as necessary.

To install:

  1. Inspect the exhaust gas passages in the intake manifold and clean as necessary. Clean the EGR valve assembly as necessary.
  2. Using a new gasket, install the EGR valve.
  3. Tighten the EGR valve securing nuts to 17-19 ft. lbs. (22-25 Nm).
  4. Install the hose on the EGR valve.f9ec12f.gif

Oct 22, 2010 | 1995 Subaru Legacy

1 Answer

Just replaced EGR hose & valve copver gaskets on 2002 Ford Escape 4WD. Did test drive, runs really rough & almost stops & cuts off. Any ideas?


OK, if you replaced the EGR hose, did you go all the way to change the EGR Valve? A stuck open EGR Valve can cause a rough idle and almost make it cut off.
Also, a vacuum leak on the EGR valve can cause a rough idle.

prev.gif next.gif Exhaust Gas Recirculation (EGR) Valve Removal & Installation 2.0L Zetec Engine NOTE: When the EGR tube is disconnected from the EGR valve, it must be discarded and a new EGR tube must be installed. The aluminum threads on the EGR valve must be inspected, and a new EGR valve installed if the threads are damaged.
To Remove:
  1. Disconnect the negative battery cable.
  2. Remove and discard the exhaust manifold-to-EGR tube. Use the following as a guide:
  3. Raise and safely support the vehicle
  4. Remove the splash shield
  5. Disconnect the EGR tube fitting
  6. Lower the vehicle
  7. Remove the air cleaner outlet pipe
  8. Disconnect the EGR tube from the EGR valve.
  9. Detach the vacuum line and remove the two retainer bolts.
NOTE: The EGR valve sealing surfaces are soft metals and easily damaged.
To Install:
  1. Installation is a reverse of the removal process. Carefully clean all sealing surfaces and install a new EGR valve gasket.
  2. Install a new EGR valve tube.
Detach the vacuum line (#1) and unbolt the EGR valve - 2.0L 02-04_escape_emissions_022.gif

3.0L (4v) Engine To Remove:
  1. Disconnect the vacuum line.
  2. Disconnect the EGR tube.
  3. Remove the EGR valve and discard the gasket.
NOTE: The EGR valve sealing surfaces are soft metals and easily damaged.
To Install:
  1. Installation is a reverse of the removal process. Carefully clean all sealing surfaces and install a new EGR valve gasket.
Detach the vacuum line (#1), unthread the EGR tube (#2) and remove the EGR valve bolts (#3) - 3.0L (4V) 02-04_escape_emissions_023.gif

Aug 02, 2010 | 2002 Ford Escape

1 Answer

Picture of egr valve and were it is located


dffc43b.jpg

Fig. 11: EGR valve and component mounting-3.0L engine


da251ab.jpg

Fig. 12: EGR valve and component mounting-3.8L engine

Removal:
  1. Disconnect the negative battery cable.
  2. If necessary, remove the air inlet tube from the throttle body and air cleaner housing.
  3. Label and detach all vacuum hoses from the EGR valve.
  4. Label and detach any electrical wiring harness connectors from the EGR valve.
  5. Disconnect the EGR valve-to-exhaust manifold tube from the EGR valve.
  6. Remove the EGR valve mounting fasteners, then separate the valve from the upper intake manifold.
  7. Remove and discard the old EGR valve gasket, and clean the gasket mating surfaces on the valve and the intake manifold.
To install:
  1. Install the EGR valve, along with a new gasket, on the upper intake manifold, then install and tighten the mounting bolts to 15-22 ft. lbs. (20-30 Nm) on 3.8L engines, or to 106-159 inch lbs. (12-18 Nm) on 5.0L engines.
  2. Connect the EGR valve-to-exhaust manifold tube to the valve, then tighten the tube nut to 30 ft. lbs. (41 Nm).
  3. Connect all wiring or hoses to the EGR valve.
  4. Install the air inlet tube.
  5. Connect the negative battery cable.

Hope this helps (remember comment and rated this).

Jul 27, 2010 | 1995 Ford Windstar

1 Answer

How do I locate and replace EGR valve?


Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} EXHAUST GAS RECIRCULATION (EGR) VALVE REPLACEMENT

REMOVAL PROCEDURE
1. Turn OFF the ignition. 2. Disconnect the EGR valve electrical connector 3. Remove the bolt retaining the pipe assembly from the EGR valve and carefully pull the pipe assembly back. 4. Remove the EGR valve retaining bolts. 5. Remove EGR valve assembly. 6. Remove the gasket. INSTALLATION PROCEDURE
1.
Install the EGR Valve with a new gasket to the intake manifold. NOTE: Refer to Fastener Notice in Service Precautions.
2. Install the bolts through the EGR valve. Tighten Tighten the bolts to 30 N.m (22 lb ft) 3. Connect the pipe assembly to the EGR valve. 4. Install the bolt. Tighten Tighten the bolts to 30 N.m (22 lb ft) . Connect the EGR valve electrical connector.

Jan 30, 2010 | 2001 Buick Regal

1 Answer

Does anyone have engine schematics for a 2003 pontiac 3.1 V6? Or know of a site where I can find engine schematics? I have to replace an EGR Valve but don't know where it is located.


If you don't know where the EGR Valve is located, it is safe to assume that you did not properly diagnose your EGR system...how do you know the valve needs replacing?

If you are trying to fix a trouble code P0401 " Exhaust Gas Recirculation (EGR) Insufficient Flow" (This is a very common code with 3.1L GM Engines)
An EGR Valve replacement will most likely make you about $125 poorer than you were before and will not fix the problem.

Your EGR port into the intake manifold is most likely clogged up and needs to be cleaned out.

You will need a Throttle Body Gasket, an EGR Gasket, a can of ThrottleBody and Intake Cleaner, and a little antifreeze. (You will lose just a little when you remove the throttle body.)

d859ab3.gif
Remove the EGR Valve and the Throttle Body. Use a screw driver or pick to chip out the carbon buildup in the EGR port going into the intake manifold. You will probably have to work it from the intake side as well as the EGR side to get as much of the black carbon out as possible. Be careful not to let this stuff go down into the intake plenum - you will burn some valves if it gets in there. Then use the Throttle Body and Intake cleaner to finish the cleanup. (It helps to take a rag and stuff it into the intake manifold just past the EGR port to catch the gunk so it doesn't go down into the plenum...just don't forget to remove the rag before putting the Throttle Body back on)

Put everything back together and top-off your antifreeze and clear your computer codes. That should fix it.

Oct 27, 2009 | 2003 Pontiac Grand Prix

1 Answer

Check engine light on when check it insufficent EGR valve


yes the passages can be cleaned. They pass exhaust gas into the intake maniflod for reburning.

It could be the DPFE that controls the EGR too. Diff. Pressure Feedback EGR.

there is also a vacuum regulator valve and a solenoid too.

Please rate as fixya if this helps.

----------------
Exhaust Gas Recirculation (EGR) Valve —3.0L (2V) Removal and Installation
  1. Disconnect the exhaust gas recirculation (EGR) valve (9D475).
    1. Disconnect the vacuum line.
    1. Disconnect EGR tube nut.
  1. Remove the EGR valve.
    • Remove the two bolts.
    • Remove and discard the gasket.
  1. NOTE: The sealing surfaces are soft metal.
    To install, reverse the removal procedure.
    • Carefully clean both sealing surfaces and install a new EGR valve gasket.
2d0d879.gif
--------------------------------------
EGR Valve —3.0L (4V) Removal and Installation
  1. Remove the EGR valve (9D475).
    1. Disconnect the vacuum line.
    1. Disconnect the EGR tube.
    1. Remove the EGR valve and discard the gaskets.
e56a6e2.gif
  1. NOTE: The EGR valve sealing surfaces are soft metal.
    To install, reverse the removal procedure.
    • Carefully clean all sealing surfaces and install new EGR valve gaskets.

Apr 07, 2009 | 2000 Mercury Sable

1 Answer

How do you replace egr valve in a 2005 dodge caravan


REMOVAL - 2.4L The EGR valve and Electrical EGR Transducer are serviced as an assembly.
  1. Disconnect vacuum tube from electric EGR transducer. Inspect vacuum tube for damage.
  2. Remove electrical connector from solenoid.
  3. Remove EGR tube bolts from EGR valve.
  4. Remove EGR valve from cylinder head adaptor.
  5. Clean gasket surface and discard old gasket. Check for any signs of leakage or cracked surfaces. Repair or replace as necessary

INSTALLATION - 2.4L The EGR valve and Electrical EGR Transducer are serviced as an assembly.
  1. Assemble EGR valve with new gasket onto the cylinder head adaptor.
  2. Loose assemble the bolts from EGR valve to EGR tube.
  3. Loose assemble the bolts from EGR valve to cylinder head.
  4. Tighten bolts from EGR valve to cylinder head to 22.8 N·m (200 ±25 in. lbs.) torque.
  5. Tighten bolts from EGR valve to EGR tube to 11.9 N·m (105 ±20 in. lbs.) torque.
  6. Reconnect vacuum hose and electrical connector to electrical EGR transducer.

Aug 03, 2008 | 2007 Dodge Caravan SXT Minivan New Cars

Not finding what you are looking for?
2003 Mitsubishi Eclipse Spyder Logo

Related Topics:

164 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...