Question about 1993 Jeep Wrangler

1 Answer

1993 jeep wrangler what dot brake fluid does it take

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 490 Answers

Dot 3

Posted on Jul 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1993 Honda Accord Brake Fluid Type. What type of brake fluid is good for my 1993 Honda Accord - DOT 3 Synthetic or Mineral.


Hi,
Just use a normal DOT-3 brake fluid! Just always check the color and level of the fluid!
If it is dirty( black ) u need to drain the whole system and put in a new DOT-3 brake fluid!

Jun 14, 2011 | 1993 Honda Accord

1 Answer

What fluid goes in the hydraulic release bearing on a 1990 jeep


If you mean the clutch throw out bearing??? No fluid goes into it, as it is sealed with grease packing inside. You may have a hydraulic clutch that actuates it, and that takes brake fluid. On the resevoir cap lists what kind. (DOT 3 or 4) This system is like a minature brake system, closed.

Mar 29, 2011 | 1990 Jeep Wrangler

1 Answer

I have a 1993 Jeep Wrangler. Does the clutch run off the hydrolic brake lines?


No, it has it's own line and fluid reservoir going to the slave cylinder.

Nov 19, 2010 | 1993 Jeep Wrangler

1 Answer

I am new to jeeps and need to know the following: what specific type of oil and or fluids to use for: 1. engine 2. transmission 3. power steering 4. brakes


1. regular anti-freeze with 50/50 water mix for coolant
2. oil is 10W-30 regular or synthetic
3. brake fluid: DOT 3 OR 4
4. automatic transmission fluid: ATF+4
5. differential without trailer towing package: 80W-90. with trailer package, use 75W-140 synthetic
lube and (4) ounces of friction modifier
6. Transfer case: Dexron IV or multi-vehicle synthetic ATF
7. power steering: standard power steering fluid.

Nov 10, 2010 | 1998 Jeep Wrangler

1 Answer

How do you do you bleed a clutch line on a 1993 jeep wrangler?


Just like you would bleed brakes. Fill the reservior with brake fluid, open the bleeder screw and have a friend press the clutch pedal in. Close the bleeder screw and let up on the clutch. Do that until the clutch pedal has a good feel. Be sure to check the reservoir frequently as they don't hold much fluid and if you let it get low you'll **** more air into the system.

Jul 31, 2010 | 1993 Jeep Wrangler

2 Answers

Where is the bleed valve for clutch on a 1991 jeep wrangler


1. Fill master cylinder reservoir with DOT 3 brake fluid. Raise and support vehicle. Attach bleeder hose to bleeder screw on bleed line of slave cylinder. See Fig. 1 (attached in link) . Place other end of hose in glass container 1/2 full of brake fluid. Loosen bleeder screw while holding bleeder screw fitting.

2. Have an assistant depress clutch pedal to the floor. Tighten bleeder screw and release clutch pedal. Repeat bleeding procedure until fluid entering container is free of bubbles. DO NOT allow reservoir to run out of fluid during bleeding. Refill clutch master cylinder reservoir.

CAUTION: DO NOT allow bleed line to bend or flex when loosening
bleeder screw.

FIG1: http://anubiscycle.com/fixya/91wranglerslaveassy.png

Jan 14, 2010 | 1991 Jeep Wrangler

1 Answer

Brake fluid seems to be full


bleed brake lines they have air in them

Mar 21, 2009 | 1993 Jeep Wrangler

1 Answer

Hard to push clutch in on my 1993 Jeep Wrangler


is the slave cylender full of fluid?

Dec 30, 2008 | 1993 Jeep Wrangler

1 Answer

Push down on clutch pedal can't get car into gear


Likely, you have a hydraulic clutch system. Check clutch master cylijnder for fluid and leakage, check hydraulic line and slave cylinder for leaks. If fluid low or empty, bleed as you would a brake wheel cylinder. If full,have someone work the clutch while you watch slave cylinder to make sure it is moving clutch fork. If system full and little or no movement, the master may be "bypassing" internally (replace) Also, check pedal mechanical linkage. Not often but sometimes these parts can break! Could also be athat clutch itself is worn, but this does not happen overnight and you would have noted slip long before this!

Dec 29, 2008 | 1993 Jeep Wrangler

Not finding what you are looking for?
1993 Jeep Wrangler Logo

Related Topics:

289 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...