Question about 1990 Oldsmobile Cutlass Ciera

1 Answer

Crank shaft pulley

How hard is it to replacing the crank shaft pulley

Posted by on

  • Anonymous Mar 21, 2014

    Its the crank shaft pulley

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,392 Answers

Not too hard if you have a pulley puller. Remove the belt, remove the crank shaft bolt, pull the crank pulley off, then reinstall in reverse order.

Posted on Jul 02, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Crank shaft pulley


crank sensor damaged when changed crank pulley.

Aug 05, 2012 | Toyota Camry Cars & Trucks

2 Answers

Crank shaft pully makes noise


Cranshaft pulley is bad,probably has rubber damper which is damaged or worn loose.Don't run it this way.Get the pulley replaced now. don-ohio

Oct 31, 2011 | 2001 Chevrolet Corvette

1 Answer

Bottem pulley on engine block is making noise, I think the bearings are going out. What is this pulley attached to and can it be lubricated?


the bottom pulley is the crank pulley. It is attached to the crank shaft. It has two parts, an inner and an outer that are joined together with a rubber isolator. Over time the rubber breaks down and the inner part part of the puller will start to rotate independently from the outer part of the pulley creating a unigue clacking noise.

To solve this you'll need a standard crank pulley puller set. You'll remove the crank bolt and then use the pulley puller to pull the crank pulley off of the crank shaft. The install the new pulley making sure to torque the crank pulley bolt to the proper spec.

Nov 06, 2010 | 1998 Buick Park Avenue

1 Answer

Replaced serpintine belt for power steering, alternator and crank shaft but belt still squeels. And appears to be tight. Slack is of 1/4 in..Is there one of these three components froze up. Power steering...


The crank shaft is not froze up if the engine is running. Without knowing how severe the situation is, it is probably best to remove the belt and feel each pulley or drive wheel to detect the condition of the bearings. It should be very clear which pulley bearing is loose by "wiggling" the pulleys. One of the pulleys will have a lot of play in the bearing. Also the pulley with the bad bearing will be hard to turn by hand with the belt off. Be sure to check every pulley on that belt circuit, except the crank shaft, you can't turn it by hand.

Sep 12, 2010 | 1998 Mitsubishi Eclipse

1 Answer

Where is the crank shaft sinsor located?


just beside the lower crankshaft pulley. The crank pulley aka. balancer will have to come off to replace sensor.

May 17, 2010 | 1991 Buick Park Avenue

1 Answer

How to replace timing belt 1995 vw golf


  1. remove air intake pipe, and box (upper and lower section)
  2. take off timing belt cover
  3. take off serpintine belt, and v belt
  4. rotate engine to TDC marks line up on crank and cam. camshaft says O^T on it and on the cover behind gear, crank has a notch in the pulley and a arrow on the cover to line up
  5. remove crank pulley 6mm allens not the 19mm 12 bolt
  6. make sure timing belt is still at TDC remove lower timing belt cover there is 3 bolts and a nut holding it on the nut is by the water pump and the bolts are on on top and 2 behind the crank pulley
  7. remove cover
  8. mark intermediate shaft shaft right above the crank pulley
  9. remove belt
  10. install reverse of removal make sure to line up all 3 pulleys cam crank and intermediate shaft or it wont run and depending on how bad it is out of time if you do it wrong you could bend valves
Assuming this is a 2.0 8v your question is pretty vague

Feb 23, 2010 | 1995 Volkswagen Golf

1 Answer

Need to know where crank sensor is located.


Hello. The crank shaft sensor is located in the front of the motor on the crank pulley or it may be part of the damper pulley. It is hard to see,... you will need to get under the car to see it but it will be right in that area near the bottom of the engine.

Feb 03, 2010 | 1998 Chrysler Cirrus

1 Answer

I have 1993 bmw 740il I try to replace the


Hi, you must take off the crank shaft pully to access the water pump use # 13 mm socket or Torx socket (not sure wich one) to take off the crank shaft pulley bolts.
Good Luck!!

Jan 10, 2010 | 2006 BMW 750Li

2 Answers

Where is the crank sensor located on a chevy malibu 2001


It should be down near the crankshaft pulley. Remove the the right front wheel and the splash shield, it should be there next to the pulley.

Dec 20, 2009 | 2001 Chevrolet Malibu

1 Answer

Crank sensor location on 2000 Cirrus with 2.5 motor


hi ronco your crank shaft sensor should belocated in the front of ur motor on the crank pulley or it may be part of the damper pulley or behind it but it will be hard to see,... you will need to get under the car to c it but it will be right in that area torwards the bottom

Dec 24, 2008 | 1996 Chrysler Cirrus

Not finding what you are looking for?
1990 Oldsmobile Cutlass Ciera Logo

Related Topics:

390 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...