Question about Chrysler Sebring

1 Answer

I am having trouble with the ac on my 2006 chrysler sebring. when i turn on the car it works fine then after about 10-15 min the pressue goes down and eventually gone. what is it and how to fix it?

Posted by on

  • candracwilso Jul 02, 2009

    well say the control is on the 4th setting being the highest you hear it in the dash working but it just dosent blow out of the vents

  • yadayada
    yadayada May 11, 2010

    what pressure goes down, do u mean the low side pressure?



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert who has answered 200 questions.


    An expert whose answer got voted for 20 times.

  • Expert
  • 363 Answers

Check your teperature control setting, the temperature setting is satified when the blow fan slows down. You need to lower the temperature setting or manuelly the the fan control to the right for higher speed

Posted on Jul 25, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

2006 Sebring Touring 2.7

Check TPS sensor and IAC sensor.

May 08, 2013 | 2006 Chrysler Sebring 2.7

1 Answer

2005 dodge caravan, instrument panel stopped working and so did my turn signals and brake lights

from having a died battery the body control module goes into back up mode from a low battery so disconect the battery for 5 min that should reset it

Oct 14, 2012 | 1999 Chrysler Sebring

1 Answer

How do I properly replace my 2006 Chrysler Sebring ac condenser? Can I use a condenser from a 2004 Chrysler Sebring?

You can replace the condenser easy enough

You won't be able to recover the refrigerant when
you start,so right there your breaking EPA Laws

Then you won't have gauges or a vacuum pump,
so you can not even work on the A/C System
to test or charge it !!

Jul 18, 2011 | 2006 Chrysler Sebring

1 Answer

How to fix tension on the alternator 2006 Chrysler Sebring 4door sedan

Depending on what system they used in your vehicle this is either automatic by a spring loaded tensioner or there are adjustmenters attached to the Alternator, Power steering or AC compressor mounts. You can move these adjusters using a socket on the end of them. It's hard to explain them but typically to tighten the belt you turn the adjusting bolt clockwise and loosen it by turning it counter clockwise.

Jul 26, 2010 | 2006 Chrysler Sebring

1 Answer

I have a 2004 2.7 6 chrysler sebring lxi. ac blows really cold and periodically just starts blowing warm air. is there a relay or temp. sensor that might be going out and through a malfunction shuts down...

Cooling fans working? If you notice the air getting warm mostly while stopped, probaby cooling fans not turning on. if the fans are working properly, may be low on freon and need a recharge.

Jun 26, 2010 | 2004 Chrysler Sebring

1 Answer

2000 Sebring Convertible Electrical Problem

have your BCM(body control module) checked,this is a problem that happens a lot on certain chrysler models and vans,also have the abs system scsnned for TC'S(trouble codes

Sep 08, 2009 | 2000 Chrysler Sebring

1 Answer

Fuse keeps blowing out

rol down window instead! ok kidding, does fan alone work ok? it might be your clutch shorted drwaing too many amps. its wheat engages your compressor when you turn on ac.

Mar 30, 2009 | 1997 Chrysler Sebring

2 Answers

Replacing headlight bulbs on a 2006 chrysler sebring

Behind the headlight you should see a eletrical wires running to the headlight section. There will be a 2 inch round plastic ring. You grap the back of the bulb and turn it to the right which will release the bulb and the socket. You pull out the bulb and replace it the same way. If this doesnt help then get back to me.

Feb 06, 2009 | 2006 Chrysler Sebring

1 Answer

Trouble code (MIL) reset

just 10 flashes means that the OBD readiness monitors have not all been set.. when the battery was disconnected it reset the monitor status to not ready..

Jan 28, 2009 | 2005 Chrysler Sebring Conv

1 Answer

Car stopping when slowing down

make sure the idle motor is conected

Jun 01, 2008 | 2000 Chrysler Sebring

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides