Question about 1998 Ford Explorer

1 Answer

Are instructions on how to install a starter

Are instructions available on how to install a starter

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 52 Answers

Check out you tube that will give you a good idea
very easy a couple bolts and two wires i believe

Posted on Jul 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Install starter


INSTRUCTIONS: REMOVE NEGATIVE BATTERY CABLE, AIR INLET DUCT,TOP STARTER BOLT,LOWER STARTER BOLT,STARTER ELECTRICAL CONNECTIONS, LOWER STARTER. TO INSTALL:PUT STARTER BACK INTO SPACE, PUT BOTH BOLTS BACK IN SNUG THEM UP THEN TORQUE THEM AT 37 FT.LBS.,REATTACH STATER ELECTRICAL CONNECTIONS( BEST TO MARK WIRES TO WHERE THEY GO AS YOU REMOVE THEM), ATTACH AIR INLET DUCT BACK TO THROTTLE BODY, RECONNECT NEGATIVE BATTERY CABLE.wencal1963_1.gif

Jan 08, 2011 | 2004 Chevrolet Cavalier

1 Answer

Need to know how to install starter on 2000 lincoln town car


Please see my tip at http://www.fixya.com/cars/r5973094-starter_replace . These are generic instructions. Specific instructions for your car from autozone.com are pasted below. Please get back to me if you have any questions.


Removal & Installation

  1. Remove or disconnect the following:

    Negative battery cable and properly isolate to prevent accidental reconnection Red solenoid safety cap Wires from solenoid 2 upper bolts 1 lower bolt and starter





f0e8ee9.gif

Fig. Starter motor mounting


To install:

  1. Install or connect the following:

    Starter and lower mounting bolt 2 upper mounting bolts. Tighten all 3 bolts to 15-20 ft. lbs. (20-27 Nm). Wires from solenoid and tighten the nut to 40-50 inch lbs. Red solenoid safety cap Negative battery cable

Oct 29, 2010 | 2000 Lincoln Town Car

2 Answers

How much should it cost to replace the starter in my 2004 Mercury Sable? I did it with a friend about 3 years ago but this time I have to pay a shop. This is the third starter. Only 68,000 miles on the...


You would have to shop around. Refurbished starters might run between $50 to $70. New ones $100 up. If you are having a mechanic do it, the repair cost for a 2 hour job might cost you $100 up. If you are to do it yourself, check with the internet. Complete easy installation instructions are availlable. Just type how to replace a starter on a 2004 Marcury Sable and print them out. Hope this serves you well and good luck with your project.

Oct 14, 2010 | 2004 Mercury Sable

1 Answer

I need to replace the existing starter in my 2003 Ford Taurus wagon. I know that I have to jack the car up in order to remove the old starter. What I don't know, is how many bolts need to be removed...


Because of the Variety of mounting methods there are 2 to 4 bolts that should be visible as you look at the starter itself. Not counting the wiring connections. If this a sideways mounted motor with the Starter mounted on the front of the motor there will be 2 bolts holding it in place. If the motor is mounted regularly with the transmission extending under the vehicle the starter in on the rear of the motor near the firewall and will have up to 4 bolts holding it in place but most likely no more than 3. I would recommend getting a Haynes repair manual on the vehicle for more detailed instruction on removal and installation. This manual or a Chilton's manual are both available at the major Auto Parts stores and are fairly inexpensive.

Aug 28, 2010 | 2003 Ford Taurus

1 Answer

My starter is acting up. i am in the process of purchasing a new starter and will install it myself. just need how to install it in easy steps


disconnect the negative battery terminal. make sure the radio doesn't need a security code to work after power is removed. if it does, get the code. you can also use a memory saver. available at parts stores. it plugs into the power outlet/cigarette lighter and holds memory for the computer and the radio.

remove the elecrical connections from the stater, remove the bolts holding the starter. install in reverse order. easy as pie
you can go to autozone.com and register your car. repair guides are available for free

Jun 13, 2010 | 1997 Toyota RAV4

1 Answer

I need to replace the starter on my 2001 dodge caravan sport. Where would I find instructions?


Caravan, Grand Voyager, Town and Country, Voyager, 2000-2004
Starter - Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    Negative battery cable Starter harness connectors Starter motor
To install:
Install or connect the following:
Starter motor. Torque the bolts to 35 ft. lbs. (47 Nm). Starter harness connectors. Torque the battery cable nut to 100 inch lbs. (11 Nm). Negative battery cable


Hope this help (remember comment and rated this).

May 14, 2010 | 2001 Dodge Caravan

1 Answer

How to change starter on 2000 chevy silverado


These instructions are for a 5.3L. Unless it is a V6 or diesel, the instructions will be similar if you have a different gas V8.
  1. Disconnect the negative battery cable
  2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  3. Remove the protective shields as necessary.
  4. Remove the starter solenoid shield.
  5. Remove the starter to transmission close out cover bolt.
  6. Disconnect the engine oil level sensor connection.
  7. Remove the front axle mounting bracket through bolt nut, if equipped with four wheel drive (4WD).
  8. Reposition the front axle mounting bracket through bolt until the bolt tip is flush with the support bushing. Do not remove the bolt, if equipped with 4WD.
  9. Remove the mounting bolts from the engine block.
  10. Slide the starter forward until the starter clears the transmission.
  11. Remove the starter transmission close out cover
    1. Disconnect the positive battery cable and wiring harness from the starter.
    2. Remove the starter from the vehicle.
      1. Connect the positive battery cable to the starter. Tighten Tighten the nut to 16 N.m (12 lb in) .
      2. Install the starter transmission close out cover.
        1. Install the mounting bolts to the engine block. Tighten Tighten the bolts to 50 N.m (37 lb ft) .
        2. Reposition the front axle mounting bracket through bolt until the bolt is fully seated. if equipped with 4WD.
        3. Install the front axle mounting bracket through bolt nut, if equipped with 4WD. Tighten Tighten the nut to 90 N.m (67 lb ft) .
        4. Disconnect the engine oil level sensor connection.
        5. Install the starter to transmission close out cover bolt.
        6. Install the starter solenoid shield.
        7. Install the protective shields as necessary.
        8. Remove the safety stands.
        9. Lower the vehicle.
        10. Connect the negative battery cable. Tighten Tighten the bolts to 17 N.m (13 lb ft) .

Oct 01, 2009 | 2002 Chevrolet Silverado

1 Answer

Replace an alternator on a 2005 chevy venture (instructions)


REMOVAL PROCEDURE

IMPORTANT: This vehicle uses the PG260 F1 starter motor. The starter motor is serviced only as a complete unit.

  1. Disconnect the battery ground (negative) cable from the battery.
  2. Raise and suitably support the vehicle. Refer to Vehicle Lifting.
  3. Remove radiator air baffle assembly.
  4. Remove the starter motor BAT terminal nut and electrical leads.
  5. Remove the starter motor S terminal nut and electrical lead.
  6. Remove the torque converter co
  7. Remove the starter motor bolts.
  8. Remove the starter motor.
INSTALLATION PROCEDURE
  1. Install the starter motor.
  2. Install the starter motor bolts. Tighten the starter motor bolts to 47 N.m (35 lb ft)
  3. Install the torque converter cover.
  4. Install the starter motor S terminal electrical lead and nut. Tighten the starter motor solenoid S terminal nut to 3 N.m (27 lb in).
  5. Install the starter motor BAT terminal electrical leads and nut. Tighten the starter motor solenoid BAT terminal nut to 10 N.m (89 lb in) .
  6. Install radiator air baffle assembly.
  7. Lower the vehicle.
  8. Install the battery ground (negative) cable to the battery.

Jul 25, 2009 | 2005 Chevrolet Venture

1 Answer

Installation instructions/diagram for 1998 volvo s70 starter


IT is very easy get all of the intake ducts out of the way to get access to the starter motortakk off rubber boot and first disconnect neg battery terminal next unbolt two bolts that hold starter and the 3 wires and ground terminal from starter (i have a 14 millimeter wrench that i cuit in half to make removal easier) and you should be all-set

May 30, 2009 | 1998 Volvo S70

1 Answer

Need to replace starter need info on how to do it.


chb725: If you go to mybunkey solutions and see the heading " "Starter, battery and alternator ok", you will find that I have given instructions for the removal and installation of a starter for a 1995 Nissan Maxima, in great detail.
The instructions include the tools needed, proceedures in a sequence more detailed (which you will not find in any book) and precautions to be taken during the removal and installation of the starter.
I hope this will provide the answer you are looking for. If not, I will await a more detailed request from you.

Apr 20, 2009 | Nissan Maxima Cars & Trucks

Not finding what you are looking for?
1998 Ford Explorer Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...