Question about 2000 Daewoo Lanos

1 Answer

Where is crankshaft sensor in 2000 daewoo se - 2000 Daewoo Lanos

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Daewoo Master
  • 450 Answers

On single cam engines it is bolted to block near front of engine next to harmonic balancer pulley(crank pulley)
on twin cam engines on type lives in block under front engine mount air con compressor and power steering bracket
the other lives in rear section of engine block (trans end) just above sump near oil filter

Posted on Jul 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHAT IS CORRECT TIMING MARKS FOR TIMING BELT INSTALLATION. 2000 NUBIRA 2.0 DOHC AND CRNKSHAFT MARKS. Thanks Joe


TIMING BELT
Removal
Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove resonator from throttle body. Remove air filter housing.
Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove serpentine accessory drive belt.
Remove crankshaft pulley bolts. It is NOT necessary to remove crankshaft sprocket center bolt. Remove crankshaft pulley. Lower vehicle.
Support engine assembly from above with Support Fixture (J-28467-B). Remove engine mount bracket from timing belt end of engine.Remove power steering hose clamp bolt, and position hose away from timing belt cover. Remove front timing belt cover. Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine).
Align mark on crankshaft sprocket with notch at bottom of rear timing belt cover. See Fig. 4 . Align camshaft sprocket timing marks with notches on valve cover. See Fig. 5 .
CAUTION: Engine damage could result if camshaft sprockets are not properly aligned with notches on valve cover.
Loosen the automatic tensioner bolt. Use an Allen wrench to rotate tensioner and relieve tension on timing belt. Remove timing belt.
Fig. 4: Aligning Crankshaft Sprocket Timing Mark
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim_4.jpg
Fig. 5: Aligning Camshaft Sprocket Timing Marks
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim2_3.jpg
Installation
Ensure crankshaft and camshaft timing marks are still aligned. Install the timing belt. See Fig. 7 . Turn the timing belt tensioner counterclockwise to tension the timing belt. Turn tensioner until the pointer aligns with the notch on the rear timing belt cover. Tighten automatic tensioner bolt to specification. See TORQUE SPECIFICATIONS .
Using crankshaft center bolt, turn crankshaft clockwise (as viewed from timing belt end of engine) 2 full revolutions. Ensure timing belt tensioner pointer is still aligned with notch.
If timing belt tensioner is correctly aligned, install timing belt cover. See Fig. 3 . Install the engine mount bracket on the timing belt end of engine. Position power steering hose in place, and install clamp bolt. Install crankshaft pulley. Install serpentine accessory drive belt.
Install right front splash shield. Install right front wheel. Install air filter housing and resonator. Connect air intake temperature sensor connector. Connect negative battery cable.
Fig. 7: Identifying Timing Belt Routing
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim3_1.jpg
here

http://www.2carpros.com/questions/daewoo-leganza-2000-daewoo-leganza-timing-marks

Feb 17, 2011 | 2000 Daewoo Nubira

1 Answer

2000 Daewoo Lanos 'jumps' when pulling away and in low gears.


Ignition Coil, or Crankshaft sensor going bad. Change your spark plugs and wires then see what happens. Or could be your injectors are clogged. Try some pour in the tank Fuel Injector Cleaner like STP. Any little debris can mess them up.

Oct 31, 2009 | 2000 Daewoo Lanos

1 Answer

Daewoo lanos year 2000 se electric rad fan has stopped working.


Find auto the temperature sensor , disconect the two wires and make a "jumper" between them, use a wire equal or with larger "diameter" (section) as the sensor wires itself. Turn the engine on. If you have already checked fuse and relay and you 100% sure they're ok the fan must start spinning...be carefull with the fan blades. If not, you may disconnect the fan wires and supply energy straight from the battery. Be carefull again some sparks may come out and try not to short circuit the wires that may create another electrical/electronic problem, okay? Hope this can help...vmossmann from Brazil

Oct 21, 2009 | 2000 Daewoo Lanos

1 Answer

Were is the crankshaft sensor on my 2000 daewoo leganza


To find the crankshaft sensor you will have to.
Remove the power steering pump if equipped,
Remove the a/c compressor,
Remove the a/c compressor mounting bracket bolt.
Remove the accessory mounting bracket.
Once you pull the a/c bracket out of the car you will see the
cranshaft position senor (CKP).
Remove the one bolt that hold it in place.
Gently rotate and remove.

Sep 20, 2009 | 2000 Daewoo Leganza

2 Answers

Engine managment light


found it at rear of sump on lefthand side also thanks for your help in solving engine management light it was the crankshaft sensor as suggested by someone on fixya

Jun 02, 2009 | 2000 Daewoo Leganza

1 Answer

Daewoo leganza 1998, speedometer is not working.


SPEEDOMETER (SPEEDO DRIVE) IS USUALLY LOCATED IN GEARBOX NORMALLY SCREWED IN SMALL BOLT YOU WILL PROBABLY FIND IT AT REAR END OF GEARBOX AS FOR RPM DIAL THAT IS USUALLY WORKED THROUGH CRANKSHAFT SPEED SENSOR BEFORE YOU GOCHANGING SPEEDO DRIVE MAKE SURE ITS NOT A BLOWN FUSE

Feb 13, 2009 | 2000 Daewoo Leganza

1 Answer

Daewoo problems


HI
is the service engine light com on when you turn the switch on ??
if no . check fuses ??
if yes . check the CKP crankshaft position sensor ??

give us more details to can help you pleas !!!
with my best wishes

Jul 15, 2008 | 2000 Daewoo Lanos

2 Answers

CrankShaft Sensor


tha crankshaft sensor is behind the powersterring pump behind the aluminum base

Jul 08, 2008 | 1999 Daewoo Nubira

Not finding what you are looking for?
2000 Daewoo Lanos Logo

Related Topics:

221 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...