Question about 1998 Honda Accord

1 Answer

How to replace drivers side axel - 1998 Honda Accord

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 19 Answers

TAKE OFF TIRES, THAN BRAKE CALIPERS, THAN BRACKET,YOU SHOULD BE ABLE TO TAKE OFF THE ROTOR NOW, TAKE OUT CENTRE NUT.TAKE OFF THE BOTTOM BALL JOINT,NOW PRY OUT THE CONTROL ARM, MOVING THE AXLE FROM THE CENTRE, USE A HAMMER AND A CHISEL LIGHTLY TO TAKE THE AXLE OUT. IF YOU NEED ANY DETAILS FEEL FREE TO ASK.

Posted on Jul 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

95 mercury villager CV Axel replacement


Shop around, look at labor prices( don't tell them are buying the part). Then buy your own part and have one replace the part. Fords.. When you have to replace the drives side CV axle. The left side has to come apart. The only way the drivers side axle comes out , is pushed out from the passenger side. Threw the transmission.

Jul 29, 2016 | Mercury Cars & Trucks

1 Answer

DIY cv axle 2008 chevy aveo


Jack the vehicle up at proper jack points and lower onto jack stand or stands.remove drivers side wheel. Use needle node pliers and a screwdriver to remove the cotter pin in the axel nut and determine the size of the axel nut. It will most likely be metric 28mm to 36mm. Use an impact to remove the axel nut. Now you will need to remove one or both of the ball joints. Start with the bottom one first and hold the axel in place and pull out on the hub. After you have the hub off of the axel note the splines and how the line up. Now turn the hub so that it is out of the way. You may be able to just yank the axel out of the transmission. If it didn't come out easily you will need a crow bar to gently pry the axel out of the case. Be careful not to put too much pressure on the transmission case. It's aluminum and it will crack and break if you beat on it. Just pry gently and with the transmission in neutral ( be sure to chalk the rear wheels so the car won't run you over) slowly rotate the axel and pry until it comes out. If that doesn't work you will need to rent a slide hammer. Thread it to the free end of the axel and forcefully slide the weight out to knock the axel about of the trans. Installation is reverse. DO NOT USE A HAMMER to force the axel back in you will mushroom the threads and never get the nut on.

Dec 06, 2013 | Chevrolet Cars & Trucks

2 Answers

2001 mitsubishi eclipse gt spyder clutch removal. how do you get the axles out and how do you release the bearing for the tranmission to seperate


After the axel is removed from the outher wheel bearingf( seaparate the steering knuckle from the lower ball joint) and pull the axel out of the bearing after the axel nut has been removed then the axel will pry ou tof the transmission.. Might take a strong pry witht he haelp of a hammer. the one side might have a carrier bearing on the CV axel that bolted to the back of the engine block. It'll have to be unbolted. too. the starter will have to be removed also as all the bolts that hold the engine to the transmission.

May 14, 2011 | Mitsubishi Eclipse Spyder Cars & Trucks

1 Answer

Looking at replacing driver side axel have remove everything but axel is there a clip or something holding the axel in place it want come out???


never done an american vehicle like this but on teh euroepon version which is a opel astra their is a spring clip inside the the shaft which is in the diff and what you do to get it out is two big screwdrivers either side and sheer brute force and ignorance and they pop out ,drain the gearbox oil first (manual gearbox) but a lot of autos are the same principle

Mar 08, 2011 | 1999 Chevrolet Cavalier

1 Answer

2005 GMC 4x4 HD 2500 6.0 eng. rear axel seal


SEAL COULD BE LEAKING CAUSE YOU DIDNT LUBRICATE THE SEAL LIPS WITH PETROLEUM JELLY TO HELP THE THE SEAL LIP SEAL OR YOU DAMAGE THE SEAL WHILE DRIVING IT IN.AXLE FLANGE NUTS TORQUE IS 58 FT LBS THE AXLE HUB NUT TORQUE IS 177 FT LBS.

Jul 14, 2010 | 2005 GMC Sierra 2500HD 4WD

1 Answer

The rear Drivers side axel has play.


I would certainly replace the axle with play. But this may not be all. Could be wheel bearing as well.

Oct 18, 2009 | 2004 Cadillac SRX

1 Answer

I have a popping or crakin noise when i turn the wheel either way


center link for steering it bolts to the frame and the axle housing

Jul 23, 2009 | 1998 Jeep Grand Cherokee

1 Answer

Uv joint noise when turning wheel on freway at 70 mph!


is clock noise, check for gres elaking on the lf side if is leaking replace the lf side drive axel

Apr 17, 2009 | Ford Escort Cars & Trucks

Not finding what you are looking for?
1998 Honda Accord Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...