Question about Chrysler LHS

1 Answer

In replacing engine timeing belt, water pump,and belt pistion tenisonar I had to remove the engine damper wheel. the car will not start and the timeing marks on ehr dual overheade cam gears are not alinging to top dead center. Can the cam gears be roated to top dead center marks in a clockwise direction from the front of the engine and the crank shaft turned to the top dead center mark with the damper wheel off,

Posted by on

  • david newman Jul 02, 2009

    None of three timeing marks will index now at the same. I suspect that the crank shaft moved when I reinstaled the damper wheel since it has no key.

  • david newman Jul 02, 2009

    The three timing marks will not index at the same time . I suspect the the crank movevd when I reinstalled the damper wheel since it is not keyed.







×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chrysler Master
  • 450 Answers

No you will bend valves if not carefull. you can only turn over from crankshaft if timing marks were in correct position in first place.

Posted on Jul 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Water pump 2000 3.0 liter dodge caravan


For The 3.0 Motor. (3.3 Way down the line.)

Drain cooling system.
Remove timing belt. Refer to Engine for procedure.
Remove water pump mounting bolts.
Separate pump from water inlet pipe and remove water pump.

Timing Belt Removal
Raise vehicle and remove accessory drive belt splash shield (Fig. 66).
Remove accessory drive belts.
Remove crankshaft pulley and damper (Fig. 68).
Support engine and remove right side engine mount.
Remove engine support bracket (Fig. 67).
Remove timing belt covers (Fig. 67).
Mark belt running direction for installation (Fig. 69).
Loosen timing belt tensioner bolt (Fig. 71) and remove timing belt.
Remove crankshaft sprocket flange shield (Fig. 68). CAMSHAFT SPROCKETS To remove camshaft sprockets
Hold camshaft sprocket with Spanner Tool MB-990775. Loosen and remove bolt and washer (Fig. 70).
Remove camshaft sprocket from camshaft. To install camshaft sprockets:
Place camshaft sprocket on camshaft.
Install bolt and washer to camshaft. Using Spanner Tool MB-990775, hold camshaft sprocket and torque bolt to 95 Nm (70 ft. lbs.) (Fig. 70). TIMING BELT TENSIONER
Install timing belt tensioner and tensioner spring.
Hook spring upper end to water pump pin and lower end to tensioner bracket with hook out (Fig. 71).
Turn timing belt tensioner counterclockwise full travel in adjustment slot and tighten bolt to temporarily hold this position (Fig. 72).

INSTALLATION


Install timing belt on crankshaft sprocket and keep belt tight on tension side (Fig. 69). Install belt on the front (radiator side) camshaft sprocket. Install belt on the water pump pulley, rear camshaft sprocket and finally on the timing belt tensioner.
Rotate the front camshaft sprocket in opposite direction to take up belt slack. Check that all timing marks are aligned (Fig. 69).
Install crankshaft sprocket flange (Fig. 68).
Loosen tensioner bolt and allow spring to tension timing belt.
Turn crankshaft two full turns in clockwise direction. Turn smoothly and in clockwise direction ONLY.
Align the timing marks on the sprockets and tighten the timing belt tensioner locking bolt to 28 Nm (250 in. lbs.) torque.
Install timing belt covers.
Install engine support bracket.
Install right side engine mount.
Install crankshaft damper and pulleys (Fig. 68). Tighten damper center bolt to 135 Nm (100 ft. lbs.) .
Install accessory drive belts.
Install accessory drive belt splash shield (Fig. 66).

Be sure to also replace all the cam and crank seals why you are there. Might as well put a belt on too.

FOR THE 3.3 OR 3.8 MOTORS.

Drain Cooling System.
Remove accessory drive belt.
Remove right front lower fender shield.
Remove water pump pulley bolts and remove pulley.
Remove water pump mounting screws. Remove water pump.
Remove and discard O-ring seal.
Clean O-ring groove and O-ring surfaces on pump and chain case cover. Take care not to scratch or gouge sealing surface

Installation

Install new O-ring into groove.
Install water pump to chain case cover. Tighten screws to 12 Nm (105 inch lbs.) .
Rotate pump by hand to check for freedom of movement.
Position pulley on pump. Install screws and tighten to 30 Nm (250 inch lbs.) .
Install accessory drive belt.
Install right front lower fender shield.
Refill Cooling System.

FOR THE 2.4 MOTOR

Disconnect negative cable from battery.
Raise vehicle on a hoist. Remove right inner splash shield.
Remove accessory drive belts.
Drain cooling system.
Support engine from the bottom and remove right engine mount.
Remove right engine mount bracket.
Remove timing belt. Refer to Engine for procedure.
Remove timing belt idler pulley.
Hold camshaft sprocket with Special tool C-4687 and adaptor C-4687-1 while removing bolt. Remove both cam sprockets.
Remove rear timing belt cover.

Install new O-ring gasket in water pump body O-ring groove. CAUTION: Make sure O-ring is properly seated in water pump groove before tightening screws. An improperly located O-ring may cause damage to the O-ring and cause a coolant leak.
Assemble pump body to block and tighten screws to 12 Nm (105 inch lbs.) . Pressurize cooling system to 15 psi with pressure tester and check water pump shaft seal and O-ring for leaks.
Rotate pump by hand to check for freedom of movement.
Install rear timing belt cover.
Install camshaft sprockets and torque bolts to 101 Nm (75 ft. lbs.) .
Install timing belt idler pulley and torque mounting bolt to 61 Nm (45 ft. lbs.) .
Install timing belt. Refer to Engine for procedure.
Install right engine mount bracket and engine mount. Refer to Engine for procedure.
Fill cooling system.
Install accessory drive belts.
Lower vehicle and connect battery cable.

Mar 29, 2012 | Cars & Trucks

2 Answers

I have no clue on how to replace water pump on a 1995 chrysler cirrus 2.5L. I have to do this myself I dont have the money for a garage.


This is found on the autozone.com website.

2.5L Engine
See Figures 3 through 7
  1. Disconnect the negative battery cable.
  2. Place a large drain pan under the radiator drain plug. Drain and properly contain the engine coolant.

This procedure requires removing the engine timing belt and the auto tensioner. To help assure proper alignment at assembly, it may be helpful to set the engine at TDC on No. 1 compression stroke. This should align all timing marks on the crankshaft sprocket and both camshaft sprockets.
  1. Remove the accessory drive belts and crankshaft damper.
  2. Remove the right engine mount. This requires safely supporting the engine with a floor jack and wood block so the mount can be removed.
  3. Remove the timing belt covers.
  4. Remove the timing belt and tensioner.



0900c152800896a7.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Remove the water pump mounting bolts


0900c152800896a8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 4: Pull the water pump assembly off of the engine and inlet pipe


0900c152800896a9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 5: Open the water pump housing and examine for cracks or damage


0900c152800896aa.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 6: Replace the water pump housing gasket using a scraper tool


0900c152800896ab.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 7: Always keep the water pump's mounting bolts lined up with their correct mounting holes

  1. Remove the water pump mounting bolts.
  2. Separate the water pump from the water inlet pipe and remove the pump.

To install:
  1. Thoroughly clean all sealing surfaces. Inspect the pump for damage or cracks, signs of coolant leakage at the vent, and excessive looseness or rough turning bearings. Any problems require a new pump.
  2. Install a new O-ring on the water inlet pipe. Wet the O-ring with water to make installation easier. DO NOT use oil or grease on the O-ring.
  3. Install a new gasket on the water pump and fit the pump inlet opening over the water pipe. Press the assembly together to force the pipe into the water pump.
  4. Install the water pump-to-engine bolts and tighten to 20 ft. lbs. (27 Nm).
  5. Install the timing belt and timing belt tensioner. Set the timing belt tension.
  6. Install the timing belt covers. Install the right engine mount. Remove the floor jack and engine block from underneath the engine.
  7. Install the crankshaft damper.
  8. Install the accessory drive belts and set to the proper tension.
  9. Connect the negative battery cable.
  10. Fill and bleed the engine cooling system.
  11. Start the engine and verify proper operation, with no leaks

Aug 20, 2011 | 1995 Chrysler Cirrus

1 Answer

WHER IS THE WATER PUMP


Try Chilton's or All Data for instructions. This is a 4.5 -5 hour ordeal for a professional and a 2 day mess for an amateur. Plus you must remove the timing belt on the 2.4L 4 Cylinder to get to the pump. Mess up here and you can damage your engine. WATER PUMP is sign with the ITEM 5 in the next diagram...

zjlimited_152.gif


  1. Disconnect the negative battery cable.
This procedure requires removing the engine timing belt and the auto tensioner. The factory specifies that the timing marks should always be aligned before removing the timing belt. Set the engine at TDC on No. 1 compression stroke. This should align all timing marks on the crankshaft sprocket and both camshaft sprockets.

  1. Raise and safely support the vehicle to a level that allows access from above and below.
  2. Remove the right inner splash shield.
  3. Remove the accessory drive belts.
  4. Place a drain pan under the radiator drain plug. Drain and properly contain the cooling system.
  5. Support the engine using a floor jack and block of wood, then remove the right motor mount.
  6. Remove the timing belt, tensioner and camshaft sprockets.

WARNING With the timing belt removed, DO NOT rotate the camshaft or crankshaft, or damage to the engine could occur.

  1. Remove the rear timing belt cover to access the water pump.
  2. Remove the water pump attaching bolts.
  3. Remove the water pump.
zjlimited_153.gif


Fig. 1: Water pump location on the cylinder block-4-cylinder engines





Fig. 2: Water pump assembly-4-cylinder engines


To install:

  1. Thoroughly clean all sealing surfaces. Replace the water pump if there are any cracks, signs of coolant leakage from the shaft seal, loose or rough turning bearings, a damaged impeller or sprocket, or a loose or damaged sprocket flange.
  2. Install a new rubber O-ring into the water pump.
Make sure the O-ring is properly seated in the water pump groove before tightening the screws. An improperly located O-ring may cause damage to the O-ring and cause a coolant leak.

  1. Install the water pump and tighten the bolts to 105 inch lbs. (12 Nm).
  2. Using a cooling system pressure tester, pressurize the cooling system to 15 psi and check for leaks. If okay, release the pressure and continue the engine assembly process.
  3. Rotate the water pump by hand to check for freedom of movement.
  4. Install the rear timing belt cover.
  5. Install the camshaft sprocket(s), timing belt and tensioner. DO NOT allow the camshafts to turn while the sprocket bolts are being tightened, in order to maintain timing mark alignment.

WARNING Do not attempt to compress the tensioner plunger with the tensioner assembly installed in the engine. This will cause damage to the tensioner and other related components. The tensioner MUST be compressed in a vise.

  1. Install the timing belt covers.
  2. Install the right engine mount bracket and engine mount.
  3. Remove the floor jack and wood block from underneath the engine.
  4. Install the crankshaft damper.
  5. Install the right inner splash shield.
  6. Lower the vehicle.
  7. Install and tension the accessory drive belts.
  8. Refill the cooling system using the correct quantity and type of coolant. Bleed the cooling system.
  9. Start the engine and check for proper operation.
  10. Check and top off the cooling system, if necessary.
2.5L Engine
See Figures 3 through 7

  1. Disconnect the negative battery cable.
  2. Place a large drain pan under the radiator drain plug. Drain and properly contain the engine coolant.
This procedure requires removing the engine timing belt and the auto tensioner. To help assure proper alignment at assembly, it may be helpful to set the engine at TDC on No. 1 compression stroke. This should align all timing marks on the crankshaft sprocket and both camshaft sprockets.

  1. Remove the accessory drive belts and crankshaft damper.
  2. Remove the right engine mount. This requires safely supporting the engine with a floor jack and wood block so the mount can be removed.
  3. Remove the timing belt covers.
  4. Remove the timing belt and tensioner.

Fig. 3: Remove the water pump mounting bolts



Fig. 4: Pull the water pump assembly off of the engine and inlet pipe



Fig. 5: Open the water pump housing and examine for cracks or damage



Fig. 6: Replace the water pump housing gasket using a scraper tool



Fig. 7: Always keep the water pump's mounting bolts lined up with their correct mounting holes



  1. Remove the water pump mounting bolts.
  2. Separate the water pump from the water inlet pipe and remove the pump.
To install:

  1. Thoroughly clean all sealing surfaces. Inspect the pump for damage or cracks, signs of coolant leakage at the vent, and excessive looseness or rough turning bearings. Any problems require a new pump.
  2. Install a new O-ring on the water inlet pipe. Wet the O-ring with water to make installation easier. DO NOT use oil or grease on the O-ring.
  3. Install a new gasket on the water pump and fit the pump inlet opening over the water pipe. Press the assembly together to force the pipe into the water pump.
  4. Install the water pump-to-engine bolts and tighten to 20 ft. lbs. (27 Nm).
  5. Install the timing belt and timing belt tensioner. Set the timing belt tension.
  6. Install the timing belt covers. Install the right engine mount. Remove the floor jack and engine block from underneath the engine.
  7. Install the crankshaft damper.
  8. Install the accessory drive belts and set to the proper tension.
  9. Connect the negative battery cable.
  10. Fill and bleed the engine cooling system.
  11. Start the engine and verify proper operation, with no leaks.

Hope this helps (remember to rate this answer).

Feb 01, 2011 | 1999 Dodge Stratus

1 Answer

How do you replace a water pump in a 2.5L V-6? Step by step.


2.5L Engine

  1. Disconnect the negative battery cable.
  2. Place a large drain pan under the radiator drain plug. Drain and properly
    contain the engine coolant.
    NOTE: This procedure requires removing the engine timing belt
    and the auto tensioner. To help assure proper alignment at assembly, it may be
    helpful to set the engine at TDC on No. 1 compression stroke. This should align
    all timing marks on the crankshaft sprocket and both camshaft sprockets.



  3. Remove the accessory drive belts and crankshaft damper.
  4. Remove the right engine mount. This requires safely supporting the engine
    with a floor jack and wood block so the mount can be removed.
  5. Remove the timing belt covers.
  6. Remove the timing belt and tensioner.





    Fig. 3: Remove the water pump mounting bolts
    90903p54.jpg






    Fig. 4: Pull the water pump assembly off of the engine and
    inlet pipe
    90903p55.jpg






    Fig. 5: Open the water pump housing and examine for cracks or
    damage
    90903p56.jpg






    Fig. 6: Replace the water pump housing gasket using a scraper
    tool
    90903p57.jpg






    Fig. 7: Always keep the water pump's mounting bolts lined up
    with their correct mounting holes
    90903p58.jpg



  7. Remove the water pump mounting bolts.
  8. Separate the water pump from the water inlet pipe and remove the pump.
    To install:

  9. Thoroughly clean all sealing surfaces. Inspect the pump for damage or
    cracks, signs of coolant leakage at the vent, and excessive looseness or rough
    turning bearings. Any problems require a new pump.
  10. Install a new O-ring on the water inlet pipe. Wet the O-ring with water to
    make installation easier. DO NOT use oil or grease on the O-ring.
  11. Install a new gasket on the water pump and fit the pump inlet opening over
    the water pipe. Press the assembly together to force the pipe into the water
    pump.
  12. Install the water pump-to-engine bolts and tighten to 20 ft. lbs. (27 Nm).
  13. Install the timing belt and timing belt tensioner. Set the timing belt
    tension.
  14. Install the timing belt covers. Install the right engine mount. Remove the
    floor jack and engine block from underneath the engine.
  15. Install the crankshaft damper.
  16. Install the accessory drive belts and set to the proper tension.
  17. Connect the negative battery cable.
  18. Fill and bleed the engine cooling system.
  19. Start the engine and verify proper operation, with no leaks.


prev.gif next.gif

Oct 29, 2010 | 1996 Dodge Avenger

1 Answer

How do you change the water pump on a 1995 nissan maxima?


Water Pump REMOVAL & INSTALLATION VG30E Engine The water pump is located in the front center of the engine. Fig. 1: The timing belt cover must be removed to fully access the water pump 89613g33.gif
NOTE: Be careful not to spill coolant on the timing belt when performing this procedure.
  1. Drain the cooling system through the drain plug at the bottom of the radiator, and the drain plugs on both sides of the block. CAUTION
    Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
  2. Remove the upper radiator hose.
  3. Loosen and remove the drive belt(s) from the water pump pulley.
  4. To make the operation easier, remove the timing belt cover. If necessary, remove the thermostat housing and gasket for access.
  5. Remove the water pump-to-engine bolts (noting different lengths) and remove the pump. If the water pump has excessive end play or rough operation, replace it. To install:
  6. Clean the gasket mounting surfaces.
  7. Use a new gasket and coat the gasket with sealant. Reinstall the pump and torque the water pump-to-engine bolts evenly to 12–15 ft. lbs. (16–21 Nm).
  8. If the thermostat housing was removed, install it with a new gasket. Install the cruise control unit if removed.
  9. Install the tensioner, tensioner bracket, air conditioning belt and adjust the belt correctly.
  10. Install the upper radiator hose.
  11. Refill the cooling system. Connect the negative battery cable.
  12. Start the engine, run to normal operating temperature and check for the correct coolant level and for leaks.
VE30DE Engine The water pump is located in the front center of the engine. Fig. 2: Water pump location and torque specifications — VE30DE engine 89613g39.gif
  1. Remove the splash shield on the passenger side of the vehicle.
  2. Drain the cooling system. CAUTION
    Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
  3. Remove the upper radiator hose to access the upper water pump bolts.
  4. Remove the small hose attached the upper part of the water pump. Fig. 3: Removing the upper radiator hose will allow better access to the upper bolts and the small hose attached to the pump 89613pj7.jpg

  5. Remove the drive belts from the front of the engine.
  6. Remove the tensioner pulley for the air conditioning compressor belt. Fig. 4: Removing the A/C belt tensioner will allow more room to remove the pump once it's unbolted from the engine 89613pk1.jpg
    NOTE: It is recommended that the crankshaft damper be removed to make water pump removal and installation easier.
  7. Remove the water pump pulley-to-water pump bolts, followed by the pulley. Fig. 5: Use a prybar with a square edge to hold the pulley in place while loosening the bolts; then unscrew them by hand 89613pj5.jpg

  8. Remove the water pump-to-engine bolts. Label each bolt, noting location, and bolt length. WARNING
    Failure to install the bolts of different lengths in their proper locations could result in a cracked timing chain cover, requiring time consuming and costly repair. Be sure to label each bolt and its location.
  9. Remove the water pump from the engine. If the water pump has excessive end play or rough operation, replace it. Fig. 6: The water pump has to be carefully positioned for removal 89613pj8.jpg
    Fig. 7: Use locking pliers and carefully twist out the timing pointer if pump removal is difficult 89613pk2.jpg
    To install:
  10. Clean the gasket mounting surfaces and grooves.
  11. Using liquid sealant, apply a continuous bead to the gasket mounting surfaces of the water pump.
  12. Install the water pump and torque water pump-to-engine bolts to 12–15 ft. lbs. (16–21 Nm).
  13. Install the water pump pulley and torque the water pump pulley-to-water pump bolts to 4.6–6.1 ft. lbs. (6.3–8.3 Nm).
  14. Install the tensioner pulley for the air conditioning compressor belt.
  15. Install the crankshaft damper, if removed.
  16. Install the timing pointer, if removed.
  17. Install the drive belts from the engine and set the proper tension.
  18. Install the splash shield on the passenger side of the vehicle.
  19. Attach the hoses to the upper water pump and the main inlet pipe.
  20. Refill the cooling system to the appropriate capacity.
  21. Start the engine, run to normal operating temperature and check for the correct coolant level and for leaks.

Jul 07, 2010 | 1995 Nissan Maxima

1 Answer

How do you remove the timing belt cover on a 1995 VW Golf.


What is needed Tools: 6mm and 8mm allen wrench socket, 5mm allen wrench. 8mm, 13mm, 19mm socket and ratchet. 10mm combination wrench. Long ratchet extensions (at least one 6in, more are helpful). 5inch Wheel puller (for main shaft pulley). (Some models may need a special spanner tool to adjust the timing belt tensioner) Parts: 2 gal of anti-freeze mixed with distilled water. All three V-belts. (Alt, A/C, P/S) $32.95 New water pump top. $91.91 New gasket for WP. $9.13 New timing belt. $26.13.


Procedure:

Remove battery cable (either power (+) or ground (-)) remove alternator remove A/C remove power steering pump .Remove water pump pulleys remove main shaft pulleys remove timing belt covers remove A/C mounting hardware remove timing belt (don't turn any of the wheels its connected to) replace timing belt adjust belt tension remove water pump face put on new gasket and new part.

Leave pulleys off. replace bottom timing belt cover, replace crank shaft pulley, replace steering pump, replace A/C, put small belt on A/C (hang loose) put large belt around A/C, Main and water pump pulley. put middle size belt on Main water pump and power steering pump reattach bolts for the steering pump pulleys put alternator back on adjust all belts. connect battery

Problem areas:
Main pulley: There are 4 6mm hex head bolts. These must be removed. The main 19mm hex head can be used to turn the engine it the timing belt slips and you have to readjust the timing.

Putting on new belts: This can be a real pain if you get VW belts. The adjustments won't give enough to put the belts over the edge so the easy way is to remove the pulley on the water pump. Then its real easy.

Timing: If you turn the wheels that the timing belt goes on you will have to reset the timing. Mark the timing points with something like whiteout so its easy to see. The timing mark on the toothed gears are small dots. The timing mark for the crankshaft is a small cut on the outer pulley. When its aligned with the intermediate wheel timing mark (there is an arrow on the cover as a hint) should intersect as viewed from the right wheel well. The camshaft timing mark should line up with the top of the engine near the front.

Power steering pump: It is held on with lots of bolts. One is in a channel that is hard to see but can be found with a 6" extension. If you look at the pump you will see three bolts that go into the housing. This should give you an idea where the forth is.

May 01, 2010 | 1995 Volkswagen Golf

2 Answers

How do I replace the serpentine belt on my 2000 Plymouth Breeze 2.4l engine?


the tensioner is on the alternator there is usually a cover over it you need to loosen the 2 screws on the alternator and turn the "adjuster" screw till the belt is loose enough to come off note the whay it is run then install and tighten the new belt it must be very tight or it will slip

Sep 14, 2009 | Plymouth Breeze Cars & Trucks

1 Answer

1995 Plymoth Voyager


The water pump bolts directly to the engine block, using a gasket for pump-to-block sealing, The water pump is driven by the timing belt and is serviced as a unit.Disconnect battery ground cable.Remove crankshaft drive pulleys and torsional damper,and Right Engine Mount & Bracket.Place a jack under engine to support and slightly raise engine, then remove engine mount bracket.
Remove timing belt cover, then mark belt running direction for reinstallation.
Loosen timing belt tensioner, then remove belt and crankshaft sprocket flange shield.
Drain cooling system.
Remove water pump mounting bolts.
Separate water pump from water inlet pipe, then remove water pump.
Reverse procedure to install, noting the following:
Use a new O-ring on water inlet pipe.
Torque water pump mounting bolts to 27 Nm (20 ft. lbs.).

Dec 24, 2008 | 1995 Plymouth Voyager

1 Answer

Honda accord


Unfortunately, u must remove the timing belt. This is why it is recommended to change the water pump when the timing belt is changed.
Here's the procedure : Disconnect neg. battery cable, remove splash shield at wheel well, (after removing wheel to help gain access, turn the engine to align timing marks and set #1 cylinder at top dead center on the COMPRESSION stroke. Once this is done, u can NOT disturb engine or u will have a fun time trying to figure out how the heck to set the timing. Drain anitfreeze, remove timing belt, remove water pump bolts (be aware that bolts may be different lengths, don't mix them up, remove water pump and O ring.
Put it back together: install new O ring and water pump, be careful Oring doesn't slip or move out of position, tighten to 9 ft lbs, install timing belt, refill antifreeze, reconnect battery cable, start car, check for leaks, bleed cooling system, replace splash shield.

Oct 19, 2008 | 1995 Honda Accord

2 Answers

Subaru impreza 1996 non turbo


REMOVE BELTS FROM FRONT OF ENGINE, REMOVE COVER ON TIMING BELT, REMOVE TIMING BELT AFTER MARKING THE WHEELS WITH THE ARROWS ON THE CAM SHAFT WHEELS. WATER PUMP IS LOCATED AT BOTTOM HOSE HOUSING IT IS A COMPLETE UNIT INCLUDING CASTING. EASY TO FIT REPLACE ALL PART AND MAKE SURE TIMMING BELT IS NOT OUT OF SEQUENCE GOOD LUCK.

Oct 12, 2008 | 1996 Subaru Impreza

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

299 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...