I need two no the vacuum hose order for my daihatsu mira L200 please if anyone can help

Hi Dear I have Mira 2014 and it’s patrole consumption is to high it’s giving me just 13 mile in a little and I am mischief upsat because before it’s give me 24 kilometres but now just giving me 13 kilometres I have checked all sencor and plug is working correctly but I don’t where the problum is plZ guide me what I can do I am very thanks if u tell me the Salution

Mira 847 cc 1993- Engine Code ED 10
Ignition data

• Ignition system type: El-ecu
• Ignition coil make/type: Dia/-
• Supply voltage: 12 + Volts with ballast resistor
• Primary resistance: 1.35-1.65 Ohms
• Secondary resistance: 22000-30000 Ohms
• Distributor make/type: Den/-
• Contact breaker gap/air: 0.2-0.4 mm
• Dwell angle: Deg\par Ignition Timing - unleaded: 5 2/900 Deg eng/rpm (without vacuum)
• Ignition Timing - leaded: Deg eng/rpm (without vacuum)
• Timing mark location: Flywheel
• No 1 plug location: Pulley
• Firing Order: 1-2-3
• Spark plug make: Bosch
• Spark plug type: WR6DC
• Electrode gap: 0.7-0.8 mm

Fuel System

• Fuel type: U/L
• Fuel pump type/pressure: bar
• Engine idle speed: 900+100/-50 rpm
• Fast idle speed: 2000 rpm
• CO level at idle speed: 1.0
• 0.5 Vol %

Engine Data

• Valve clearance - inlet: 0.25 mm (hot)
• Valve clearance - exhaust: 0.30 (hot)
• Compression pressure: 1.2-1.5 bar
• Oil pressure: 2.5-5.6/3000 bar/eng/rpm
• Radiator pressure cap: 0.6-1.05 bar/type
• Drive belt 1 - size: 9.5x925/KDB 925 mm/type
• Drive belt 2 - size: mm/type

Electrical System

• Alternator output: 10/2500 Amps/eng/rpm
• Regulated output: 14.2-14.8 Volts
• Battery: 12/35 V/Ah
• Starter motor make/type: Den/-

Other data

• Clutch operation type: Cable
• Clutch adjustment: 10-30 mm
• Cambelt failure: Damage
• Cambelt Part Number: 13514-87211
• Tyre pressures: 1.8(26)f 1.8(26)r bar (psi)
• it took me 3 seconds to google this then i realized that this is a older engine then yours

No they will not,

Go to WARFS.ORG and look for the daihatsu help link Leon is the US rep for them and knows more about them than anyone on the planet.I hope this helps, good luck !!

the fuel pump is located inside the fuel tank.

how to overhaul mira l2 gear box??

Errors codes would be the logical thing to look at first. You may need to ask Toyota for the procedure in retrieving them.

Check that there aren't any obvious cracks in vacuum hoses.

Try pinching the PCV valve hose. If it stabilises you need to clean with some carby cleaner or replace.

The H series engines are prone to this and can generally be tracked to a vapour lock in the coolant hoses on the throttle body air valve (idle circuit).

28psi

Hi,

In my past dealings with these 3 cylinder engines, common faults (depending on the engine) are:

• contact point pitting/burns (clean, scrape/replace);
• rotor;
• distributor cap;
• ignition coil;
• ignition coil ignition B+12 connector;
• ignition coil loose ground.

Please check above mentioned components.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.