Question about 2003 BMW 7 Series

1 Answer

The steering wheel on my bmw 7 series 2003 730ia model is self adjusting after a change of steering angle sensor and steering column switch.please help

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 580 Answers

Read the owners manual on resetting your door control seat preference this will include steering column and pedal adjustment if installed on your 7.

Posted on Jul 08, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change steering wheel angle how to change steering wheel angle to chrysler voyager 2003o chrysler voyager 2003


dont try removing the steering wheel as the airbag will cause this to be a problem , adjust the tracking until the wheel is in the position you want , make sure you adjust the track rods equally on each side , this is a little bit of trial and error if your doing it your self ,

Jun 25, 2016 | 2003 Chrysler Voyager

1 Answer

Trying to change the steering wheel angle module and I need to know how to remove the horn/air bag?


Most of these sensors are located at the bottom of the steering column and airbag removal is not required. Year/make/model???

Feb 04, 2016 | Cars & Trucks

2 Answers

How to adjust clutch pedal on 86 mustang lx


clutch is supposed to be self adjusting. Here are instructions for replacing the adjuster:


REMOVAL & INSTALLATION


See Figure 1

  1. Disconnect the battery cable from the negative terminal of the battery.
  2. Remove the steering wheel using a steering wheel puller, Tool T67L-3600-A or equivalent.
  3. Remove the lower dash panel section to the left of the steering column.
  4. Remove the shrouds from the steering column.
  5. Disconnect the brake lamp switch and the master cylinder pushrod from the brake pedal.
  6. Rotate the clutch quadrant forward and unhook the clutch cable from the quadrant. Allow the quadrant to slowly swing rearward.
  7. Remove the bolt holding the brake pedal support bracket lateral brace to the left side of the vehicle.
  8. Disconnect all electrical connectors from the steering column.
  9. Remove the 4 nuts that hold the steering column to the brake pedal support bracket and lower the steering column to the floor.
  10. Remove the 4 booster nuts that hold the brake pedal support bracket to the dash panel.
  11. Remove the bolt that holds the brake pedal support bracket to the underside of the instrument panel, and remove the brake pedal support bracket assembly from the vehicle.
  12. Remove the clutch pedal shaft nut and the clutch pedal, as outlined above.
  13. Slide the self-adjusting mechanism out of the brake pedal support bracket.
  14. Examine the self-adjusting mechanism shaft bushings on either side of the brake pedal support bracket, and replace if worn.

To install:
  1. Lubricate the self-adjusting mechanism shaft with motor oil and install the mechanism into the brake pedal support bracket.
  2. Position the quadrant towards the top of the vehicle. Align the flats on the shaft with the flats in the clutch pedal assembly, and install the retaining nuts. Tighten to 32-50 ft. lbs. (43-67 Nm).
  3. Position the brake pedal support bracket assembly beneath the instrument panel, aligning the four holes with the studs in the dash panel. Install the four nuts loosely.
  4. Install the bolt through the support bracket and into the instrument panel. Tighten to 13-25 ft. lbs. (18-34 Nm).
  5. Tighten the four booster nuts that hold the brake pedal support bracket to the dash panel to 13-25 ft. lbs. (18-34 Nm).
  6. Connect the brake lamp switch and the master cylinder pushrod to the brake pedal.
  7. Attach the clutch cable to the quadrant.
  8. Position the steering column onto the four studs in the support bracket and start the four nuts.
  9. Connect the steering column electrical connectors.
  10. Install the steering column shrouds.
  11. Install the brake pedal support lateral brace.
  12. Tighten the steering column attaching nuts to 20-37 ft. lbs. (27-50 Nm).
  13. Install the lower dash panel section.
  14. Install the steering wheel.
  15. Connect the battery cable to the negative terminal on the battery.
  16. Check the steering column for proper operation.
  17. Depress the clutch pedal several times to adjust the cable.
  18. 714c4a4.gif

Sep 24, 2010 | Ford Mustang Cars & Trucks

1 Answer

My steering wheel is adjusting itself while in drive and static


Read the owners manual on resetting your door control seat preference this will include steering column and pedal adjustment if installed on your 7.

Jul 02, 2009 | 2000 BMW 7 Series

3 Answers

Driver seat and steering wont adjust on my 95 740il


here's what you have to do:
#1. make sure the fuse to the seat adjustment is not blown, its usually a 10 or 15amp fuse.
#2. unscrew the cover to the controls on the driver's seat and make sure the harness is not loose or
broken, if the harness fails to attach to the control board correctly the steering wheel and the
seat adjustment will not work, this harness tends to come loose and even brake over time due to
the constant movement when you get in and out of your car.
I hope this solves your problem.

Rafael Reyes.

Jun 15, 2009 | 2000 BMW 7 Series

1 Answer

Play in the steering wheel column after position adjustment


When they did the alignment it's possible that they used a tool that locks the steering wheel straight while it's on the alignment rack.If they put too much pressure on the wheel when they used the steering wheel seat lock tool it may have stressed you tilt lock mech causing it not to lock where you want it.Hope this helps

May 16, 2009 | 2005 Hyundai Sonata

1 Answer

2000 Mercury Villager: Is there a shift lever adjustment? When placing foot on brake pedal and pulling shift lever rearward it doesn't feel like the transmission is completely disengaging and it is...


You may have a loose shift linkage in the steering column. Remove the upper and lower plastic covers behind the steerong wheel (5 or 6 philips head) and see if you have any loose torx head or allen head screws. Ea
rlier models had this isue.

Also, go to this site for Villager Quest help.

http://autos.groups.yahoo.com/group/villagerquest/
Here's adjustment procedure too

SECTION 307-05: Automatic Transaxle/Transmission External Controls 2000 Villager Workshop Manual
GENERAL PROCEDURES Cable Adjustment —Shift Control
  1. Place the gearshift lever in PARK (P) position.
  1. Raise and support the vehicle. Refer to Section 100-02 .
  1. Remove the splash shield.
  1. Loosen the shift cable nut.
  1. Position the shift linkage in PARK (P) position.
  1. Tighten the shift cable nut.
b45630b.gif
  1. Move the gearshift lever through the entire shifting range.
  1. Verify that the engine will crank with the gearshift lever in PARK (P) or NEUTRAL (N) position.
  1. Adjust the transmission range (TR) switch as necessary, refer to Section 307-01 .
-------------------------------------------------
8d76d60.gif
Item Part Number Description 1 043B13 Driver side air bag module 2 — Steering wheel nut 3 3600 Steering wheel 4 — Radio volume control cover 5 — Air bag sliding contact electrical connector access panel 6 — Cruise control cover 7 14A664 Air bag sliding contact 8 13K359 Multifunction switch 9 — Tilt wheel lever 10 13318 Turn indicator cancel cam 11 — Steering column assembly 12 — Steering column mounting bracket nuts (4 Req'd) 13 3C695 Lower column shroud 14 — Steering column opening cover nuts (3 Req'd) 15 — Steering column lower yoke bolt 16 3N725 Steering column lower yoke 17 — Steering column clamp bolt 18 3C695 Upper column shroud 19 7210 Gearshift lever

May 05, 2009 | 2000 Mercury Villager

2 Answers

2004 BMW 1 Series DTC Warning light


dtc relates to brake hydraulic pump unit 1300 top buy from bmw, the rest will be labour.

Mar 22, 2009 | 2008 BMW 1 Series

1 Answer

Steering wheel alignment


Hi

Expect Kwik Fit have adjusted the tracking / wheel alignment at some time, and adjusted one track rod more than the other. ?

Count the threads showing ! ...I expect this will become apparent.

You need to have the tracking / alignment rechecked with track rods even lengths both sides.

Then if you road test and find the steering wheel out of alignment, remove steering wheel, and move round the correct position on the steering column splines.

Hope this is of help.

Good Luck !

John.

Jan 20, 2009 | 1999 BMW 318 ti

Not finding what you are looking for?
2003 BMW 7 Series Logo

348 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Anthony Jones
Anthony Jones

Level 2 Expert

128 Answers

Doberman

Level 2 Expert

254 Answers

dhnguyen

Level 2 Expert

281 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...