Question about 1991 Chevrolet Camaro

1 Answer

We need to intall a new clutch in a 95, 8 cylander Z-28 Camero, need to how how to do it?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Chevrolet Master
  • 2,007 Answers

Remove starter, remove shifter, remove driveshaft, bell housing bolts etc. You would be well advised to get a Hane's repair manual and follow the step by step instructions. It's far too much to get for free on here. It would take half the day to type it out.

Posted on Jul 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 mercury grand marquis cylinder head to engine block torque specs


Tighten in 6 steps. These are torque to yield bolts and new bolts should be used.
1 Tighten all bolts to 28-31 ft lbs
2 Turn all bolts 85-95 degrees
3 Loosen all bolts 360 degrees
4 Tighten all bolts 28-31 ft lbs
5 Tighten all bolts 85-95 degrees
6 Tighten all bolts an additional 85-95 degrees
25985986-ai5p5eze24k2deo1fvscm5xo-2-0.gif

Nov 29, 2015 | Mercury Cars & Trucks

1 Answer

Adjust the clutch linkage on a pontiac 2002 trans am 6 speed


How to adjust clutch??? 95 bird. - Fourth Generation Pontiac ...

www.firebirdnation.com/forums/.../65178-how-to-adjust-clutch-95-bird/
Dec 5, 2008 - posted in Fourth Generation Pontiac Firebird (1993 - 2002): I have ...Year: 2000; Make: Pontiac; Model: TRANS AM; Engine: 5.7L LS1; Transmission: MANUAL 6 SPEED T-56 ... Have you looked at your clutch master cylinder. Throttle is sticking after acceleration - Fourth Generation ...
Oct 7, 2011
1 Problem / Few questions - Fourth Generation Pontiac Firebird ...
Mar 26, 2010
Firebird Technical Service Bulletins - Fourth Generation Pontiac ...
Jul 5, 2006
TECH ARTICLE MASTER INDEX Look Here - Firebird Nation
Aug 18, 2004
More results from www.firebirdnation.com

How to Install Clutch 98-02 LS1 F-Body Part 1 of 2 - YouTube

? 12:31
www.youtube.com/watch?v=4BCHu2BwBMs

Apr 12, 2013 - Uploaded by MapleBoarder78
Part one of installing a new clutch on my 2000 Trans Am. Part 2 will include installation ... How to Master Cylinder Install and Drill Mod (LS1 F-Body) - Duration: ... 6:28. Removal and Servicing ofClutch Master Cylinder to Slave Cylinder ... LS1 98-02 Chevy Camaro Z28 SS Pontiac Firebird Trans Am F-Body ...

Nov 02, 2015 | Pontiac Cars & Trucks

1 Answer

I have a 95 camero that i just put a clutch and master cylinder in but i still have no peddle and it wont go in gear what else can i do


Did you bleed the system? Visual check the slave for movement? You might have to bleed that thing about 9 times to get it going. Make sure you have a pedal before crashing it into gear. Make sure the piston is hitting the throwout arm. The piston has an adj screw on it for more length. Check it out, hope this helps.

Feb 21, 2011 | Chevrolet Camaro Cars & Trucks

1 Answer

Replaced Clutch Slave and worked good for a day . Then replaced with another new cluch slave and clutch master cy. .Worked good for a day and now pedal is slowly going back to floor


sounds like there is still air in the system
the master cylander needs to be bench bled before installing in vehicle
if that does not fix problem check fluid lines for leak

Dec 16, 2010 | 1994 Isuzu Amigo

1 Answer

Is the Engine wiring harness the same as the for automatic than a standard shift. Engine was removed from another camero,same year,the car had an automatic,my car is stardard shift


my 95 camero 3.4, won't start it has spark and fuel but i think the fuel injectors are't working. i have no check engine lite on.

Oct 20, 2010 | 1995 Chevrolet Camaro

2 Answers

When i turn my key nothing happens like its not catching or something


you will need to check the starter, check for corosion and if if has you will need to disconnect the battery and remove all the corosion from the starter wires and the starter bolts, recconnect the battery and give it a try.

Dec 23, 2009 | 1992 Chevrolet Camaro

1 Answer

92 saturn sl1 shifts hard


go to www.saturnfans.com

Mar 22, 2009 | 1993 Saturn SL1

1 Answer

95 Ford Escort Transmision problems


Sounds to me like clutch is not freeing up if you turn off motor & it goes straight into gear. Did you replace all clutch parts plate pressure plate & realease bearing its almost like there is not enough travel on master cyl or slave cyl if clutch is OK

Jun 07, 2008 | 1995 Ford Escort

Not finding what you are looking for?
1991 Chevrolet Camaro Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...