Question about 1990 Toyota Land Cruiser

1 Answer

Low beam ok, spotties ok , high beam not working

The control is in the colum, if you pull lever spotties work, back to normal position low beam iluminates, push down dash indicator
iluminates for high beam but no high beam light .

Posted by on

  • fredsontabuj Jul 03, 2009

    Is spotties and high beam is using same relay? spotties is Brown relay , if separate what suppose to
    be the color of high , the main is silver round w/c includes low beam. do you know the wire color of high beam control from the colum switch? for easy tracing until the junction plug in the colum.

    Thanks

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 104 Answers

It sounds like you have a contact problem in the column switch or the high beam relay.

Posted on Jul 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1999 Toyota Camry . Low beams work, but no high beam.


I would guess the switch on the steering column
is worn out,thus no high beam feature

That switch & that part of the lighting system has to be tested

Best if you have wiring diagrams & electrical skills

As with almost all folks that come to any web site, I assume
everyone ends up at a repair shop,because no one says otherwise

May 10, 2014 | 1999 Toyota Camry

1 Answer

Is Blue Lite For High Beam Supposed T oStay on when clicked?


To clarify, when you pull the turn signal lever towards you, the high beam lights will come on only as long as you hold the lever up. This is the flash to pass feature.
To switch the headlights from low beam to high beam, you push down on the lever towards the dash. Then the high beam lights and the blue indicator light should stay on.

Jun 09, 2013 | Cars & Trucks

2 Answers

Prius high beam lights work but low beam lights do not work?


On a 2008 Prius, If both High beams work but only one side has working low beams, then it is most likely a fuse. So before breaking your knuckles to change the bulb, check the fuse first. I found out the hard way as my mom distressed to me that her drivers side headlights were out. So without checking to see if low and high were working, I proceeded to remove and replace the bulb - ouch! There are 4 10 amp fuses that protect the circuits for low/high beam function. They are under the hood in the fuse box on the drivers side and they are marked on the box cover. Check them before changing the bulb.

Oct 29, 2012 | 2006 Toyota Prius

1 Answer

98 Ranger Headlights Not Working


Check the bulbs, if OK replace switch.

May 17, 2017 | 1998 Ford Ranger SuperCab

1 Answer

1996 80 series landcruiser no low beams high beams are fine no spotties all work when pushed into high beams exept spotties and no high beam light shown on dash... Fuses all good blown relay that fused...


Hi Grant I believe that the fuses you are looking for are 7.5 amps and they are found in the fuse cabinet under the hood. If that fails try replacing the H4 bulbs, which I'm susspecting may have blown! Regards John

Apr 26, 2012 | 1996 Toyota Land Cruiser

1 Answer

92 chevy cavalier RS, I cannont get the headlamps to turn on, the high beams work, however the normal lights do not work. The lever on the left of the steering columb controls the cruise control,...


did you check to see if the fuse was any good.if it wasn`t then replace the fuse.a fuse will not cost you $25 as you indicate.if it works after changing the fuse that`s all you have to do.it could be the dimmer switch at the base of the steering colume that changes from high to low beam lights when you move the signal arm.you can find it by looking under the dash and move the arm to activate the switch to find it.you can check for power out of the switch with a test light.the wire color will be the same as the wire at the back of the headlight for the low beam.

May 09, 2011 | 1992 Chevrolet Cavalier

1 Answer

1998 exporer Limited Edition Day time running lights don't work. I am trying to locate the DTRL Module on the vehicle. I will start by replaceing that first.Also have problem with my high beam indicator...


There is a fuse that controls; headlamps, DRL module & instrument cluster. It is the fuse box inside the vehicle mounted on the side of the dash on the drivers side and you can see the panel if you open the door. the fuse that I am talking about is in the # 33 position. If you are looking into the box the one on the very bottom closest to the firewall. There are onlt two fuses on the bottom and they are both sideways. It's a 15 Amp fuse. Ihope this helped you and good luck.

Feb 10, 2011 | 1998 Ford Explorer

1 Answer

When I turn on my highbeams, the lowbeams shut off. Is this normal?


Yes, the low beams will shut off if you turn on high beam. Not sure which way yours work but if you push the lever for high beam, pull the lever back and all lights will come on or vise versa. You would think all the lights would turn on when going into high beam.

Dec 30, 2010 | 1996 Mercury Grand Marquis

2 Answers

Low beams don't work; High beams fine. Not the


the high beam switch is at fault
A new one is needed
The directional lever you pull up on to switch to high and low connects to a rod which is going to the high beam switch at the mid section of the steering coluum. It is a headache to change for your on your head replacing this part

May 24, 2010 | 2004 GMC Envoy

2 Answers

Camry headlights not working


it sounds like a bad light switch

Mar 25, 2010 | 1993 Toyota Camry V6

Not finding what you are looking for?
1990 Toyota Land Cruiser Logo

444 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...