Question about 1996 Nissan Pickup

1 Answer

I need to replace the blower motor switch -'96 Nissan pu

Hi y'all.I am replacing the fan switch with a Indak 4 post switch,Napa part # 207419.I just need to know what the posts are labeled.They are l,m,h,b,c.
Now I know L,M,H,are low,medium,& high.And I guess b means battery-
but is c ''common''?(Neutral)? What for ? And can I use the switch even though I had a 4spd switch before ? I can figure out the wires in the truck.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 3,349 Answers

Hey, I'd do an ohms test between voltage terminal suspect and l--m--h. If B and C terminals both have continuity to the speed terminals, I don't think it makes any difference which one is voltage.
I did look at 3 speed blower motor switch, different part number. C terminal was voltage feed to switch, B terminal was for lamp, just tells you it is turned on.
Type in your part number in search box, If you find it on a web site, maybe you can email manufacturer? The manufacturer can tell you which terminal does what?

Posted on Aug 21, 2017

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 109 Answers

SOURCE: upgrading nissan almera dipped headlights?

I would have the complete headlight circuit checked out by a competent tech before buying more bulbs.

Posted on Nov 21, 2008

johnny5846
  • 379 Answers

SOURCE: replacing low beam head light on nissan altima

your welcome , glad to have assisted you

J5

Posted on Jan 21, 2009

SOURCE: need to bypass ignition switch on nissan sentra

it should be underneath your car in between the firewall and the engine. Now you don't want to supply direct power to your starter because you'll end up frying it. However to just start the car once you've located the starter, get a long screwdriver with a plastic handle and connect the two wires with the screwdriver.

As for a long term fix, without investing the money to replace the necessary parts. You will need to attach a wire that can handle 12v to both wires on your starter separately. Then connect the other ends of both wires to a switch that can handle 12v, and mount that in your car somewhere. Then whenever you need to start your car just flip the switch on until the car starts then once it is started flip it back off.
I know this sounds like a lot but it is very doable with about $5 and a little bit of time.

Posted on Jan 30, 2009

  • 2 Answers

SOURCE: 95 nissan maxima. won't start

Find the starter loctation. On top of the transmission. There should be a decent sized red wire and a smaller black wire i beleive. Anyway the smaller wire gets power from the ignition switch. Take a test light and while someone its turning the key to start it the test light should light up when touching the smaller wire on the starter. If you are not getting power to that wire it could be a broken wire or your ignition switch. If you are getting power then try tapping on the starter with a screwdriver or hammer. Lightly not to hard. It might start but either way you will need a new starter. Hope this helped

Posted on Apr 18, 2009

  • 82 Answers

SOURCE: AC blower motor resistor Nissan Maxima 2000

yeh its located under the passenger side glove box,its in the heater box beside the heater motor ,,2 scews hold it in and it looks like a credit card when its out,,,,

Posted on Apr 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Eddie Bauer Edition. how can I replace heater fan motor?


How To Install Replace Blower Motor Heater AC Fan Ford ...

? 9:30
https://www.youtube.com/watch?v=zasspzTCrSo
Oct 4, 2010 - Uploaded by 1A Auto Parts
How To Install Replace Blower Motor Heater AC Fan Ford Explorer ... This procedure should be the same or similar on 95, 96, 97, 98, 99, 00, ...

Nov 25, 2015 | 1997 Ford Expedition

2 Answers

My 2002 nissan Pathfinders heater switch works on on 1,2,3 not 4


For the screeching noise you need to replace the blower motor and for the blower motor speed you need to replace the blower motor resistor.

Dec 06, 2013 | 2002 Nissan Pathfinder

1 Answer

The heating switch( fan) works only on #4 position , how can I fix it ?


replace blower motor resistor located next to blower motor under passenger side of dash.has one connector and two phillips screws securing it.easy to do and part is fairly inexpensive.if replacement part fails i would recommend replacing blower motor also asit is probably drawing too much current and overheating resistor assembly.

Feb 20, 2011 | 2001 Nissan Sentra

1 Answer

Blower working on top 2 settings but no air comeing from vents


Hi

Thanks for using FixYa. The possible causes due to which the blower is not working normally are fuse, blower resistor or a bad blower motor. Test the voltage at the blower with a test light. Please check the motor relay switch fuse under the dashboard. Use a multi meter to measure ohms for continuity. If these are fine, bypass the blower motor relay switch to make sure blower motor is running fine. Motor relay switch is right next to radiator fan relay switch under the hood. Pull out the blower motor relay switch to see 4 female pin holes. Test the relay switch using a 12 volts power source and a multi meter to measure continuity. If fan works after jumping the pin holes, then blower motor is fine but relay switch may be faulty. You may also need to replace the blower motor resistor. If still the problem persists, then you need to replace the blower motor.

Please do rate the solution and revert for further assistance.


Thanks
Rylee

Aug 09, 2009 | 1997 Honda Civic

1 Answer

Can someone tellmehowto take the apart to replace the switch?


no the switch is fine. it needs a blower motor resister. napa part # BR391

Jul 24, 2009 | 2005 Jeep Grand Cherokee

1 Answer

A/c relay?


YOUR BLOWER MOTOR RESISTOR IS DEFECTIVE. IT NEEDS TO BE REPLACED FOR THE FAN TO WORK ON ALL SPEED SETTINGS. ON THE PASSENGER SIDE IN THE DUCT-WORK NEAR THE BLOWER MOTOR YOU SHOULD SEE IT FASTENED BY TWO SCREWS AND IT WILL HAVE A THREE WIRE PLUG GOING TO IT AS WELL. HOPE THIS HELPS. KEEP ME POSTED. THANKS FOR AN HONEST RATING AND FOR USING FIX-YA.

May 13, 2009 | 1996 Volkswagen Jetta

2 Answers

99 Nissan Altima blower fan works only on highest setting (#4)


Resistor switch. The rotary switch on the dash is very, very uncommon. It is also not the blower, because it works.

Mar 09, 2009 | 1999 Nissan Altima

1 Answer

Heater fan is SLOW....


check to be sure that nothing has made a nest in your blower motor.. I have found mouse nests, rats nests, and even dead snakes inside the blower motor on these trucks..with all the extra weight inside the blower, the low speeds turn slow and will burn the resistor out quicker.

Oct 12, 2008 | 1994 Toyota Pickup

1 Answer

Vent fan only works when set to 4


Hi.....
On your Vehicle the problem for the FAN speed is NOT the FAN switch.
99.9 % of this problem on cars is the BLOWER MOTOR RESISTOR.
The blower motor resistor give the speed to the Fan.
But on High speed the switch make a By pass of the switch using a Relay for the high speed.
The Blower motor resistor, is located Beside of the Blower motor On the passanger compartment.

If you replace the blower motor resistor you have 99.9% of this will solve your problem.

I'm a Mechanic.

I hope this help on your problem.
Thank you for use fixya...

Oct 09, 2008 | 2003 Nissan Altima

3 Answers

2001 Nissan Sentra A/C Blower Not working


I enjoyed the same problem on my 2001 Nissan Sentra three months after I moved to Florida from New England. It is not a fuse; the fan would not work at all if it was a fuse. Your problem is the fan motor resistor behind the glove box. The classic symptoms are that the fan will not operate except on 4 (full speed). You technically could replace it on your own but I took it to my Nissan dealer and had it replaced for under $100, parts, labour, tax, and coffee.

Jul 31, 2008 | 2001 Nissan Sentra

Not finding what you are looking for?
1996 Nissan Pickup Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...