Question about 1990 Eagle Premier

1 Answer

I cant figure out how to adjust the idle on my 1990 eagle premier

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 36 Answers

Unfoutunatly the computer controls this you might be able to jimmy rig something though.

Posted on Nov 26, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Keep running hot


Thermostat is stuck closed quite possibly. The thermostat would normally be closed initially to allow the engine to warm up and then it would open to allow water to circulate and be cooled. Otherwise you may have a problem with the water pump itself.

Jul 23, 2012 | 1990 Eagle Premier

Tip

CHRYSLER Eagle service how to reset maintenance light 1988-93


Chrysler,
All Models


1990-93

When "SERVICE REMINDER" appears on the Electronic Vehicle Information Center, press the "INFO" button and press the "SET" button within 5 seconds.


Eagle Premier,
Dodge Monac


1988-92

When "SERVICE" appears on the Vehicle Maintenance Monitor, press the "RESET" button located directly below the monitor. "MONITOR" should then appear on the display.



on Dec 07, 2009 | Chrysler E-Class Cars & Trucks

1 Answer

I wanted a step by step in removing old and installing new fuel pump in a 1990 eagle premier. I'm sure I can do it without it but sure makes the process easier and faster with a manual and haynes...


yes i can help i have put 3 in my eagle,undo filler screws ,take passenger rear wheel off ,off the filler spout there is an air hose to unclamp,then undo the gas tank belly strap , disconnect the wire harness plug at around the rear axle on passenger side and the gas lines and return lines they are right by the harness plug then you can locate the bolts on the tank there are 3 two in front and one by pass rear tank undo these drop tank and you have to feed the hose that's hooked to the filler tube through the frame ,once the tanks out just undo the screws and lines off the pump it pulls out if you tilt it it is really easy because you can see everything good luck .

Jul 27, 2011 | 1990 Eagle Premier

3 Answers

Idle at 250 rpm


Idle Speed Control (ISC) Motor OPERATION Eagle Throttle Body Fuel Injection (TBI) System NOTE: The Eagle TBI system is used only on 2.5L Premier engines. The Idle Speed Control (ISC) motor is mounted to the throttle body and controlled by the PCM. The throttle lever rests against the initial adjustment screw of the actuator (plunger). The idle speed is not adjustable. The initial adjustment screw is only used to establish the initial positioning of the actuator when the ISC motor has been replaced. The actuator extends or retracts to control engine idle speed and to set throttle stop angle during deceleration. Based on inputs from the various engine control system sensors and switches to the PCM supplies current to the ISC motor to adjust the actuator position for the particular operating conditions.
---

Aug 05, 2010 | 1995 Dodge Spirit

2 Answers

Were is the the low side port located for the a/c system on a 1990 eagle premier?


To do it to generic away. The low side Schrader valve cap is usually blue, and the high side is usually red. If you still don't know or do not have caps on your system find your compressor in find a line that goes to the condenser in front of the radiator this is the high side, the other line from the compressor is the low side. Good luck.

Jun 13, 2010 | 1990 Eagle Premier

1 Answer

The car will start but when you press on the gas it wants to die?


1989 Eagle Premier 2.5 liter SOHC L4 VIN "H"

3b27d6b.gif



1989 Eagle Premier 3.0 liter SOHC V-6 VIN "U"

0bcfcb1.gif


Hope this help (remember comment and rated this).

Mar 27, 2010 | 1989 Eagle Premier

1 Answer

Pulley tension diagram for a 1991 eagle premier


try going to autozone website they have lots of good stuff for you to look at and print out

Nov 20, 2009 | 1991 Eagle Premier

1 Answer

Car will crank but will not start up and run


Try fuses, fuel lines might be clogged, crimped.

Jan 02, 2009 | 1991 Eagle Talon

1 Answer

Fozen shocks-what can happen?


If you misspelled frozen and I understand your question right, you have a big problem. Frozen shocks mean your wheels will not move up and down. So when you hit a bump you will jar yourself and your car. You're going to tear a lot up real fast.

Dec 22, 2008 | 1990 Eagle Premier

Not finding what you are looking for?
1990 Eagle Premier Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Eagle Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Stewart Dibbs

Level 2 Expert

305 Answers

Are you an Eagle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...