How much would it to replace two doors and two side panels

What make ,model an year ?

Remove the door opening weather-strip. Refer to Door Opening Weatherstrip Replacement in Doors.
Remove side sill trim plate. Refer to Door Sill Plate Replacement in Interior Trim.
Remove the lower quarter panel trim. Refer to Rear Quarter Trim Panel Replacement in Interior Trim.
Remove the center pillar upper trim panel. Refer to Center Pillar Upper Trim Panel Replacement in Interior Trim.
Remove the quarter upper trim panel. Refer to Rear Quarter Upper Trim Panel Replacement in Interior Trim.
Remove the center pillar outer applique. Refer to Center Pillar Applique Replacement in Exterior Trim.
Remove the roof drip molding. Refer to Body Side Roof Drip Molding Replacement in Exterior Trim.

Important: It is necessary to use new nuts when reinstalling the quarter window.
Remove the nine quarter window nuts (1), securing the quarter window assembly (2) to the body opening.
Caution: When working with any type of glass or sheet metal with exposed or rough edges, wear approved safety glasses and gloves in order to reduce the chance of personal injury.
Important: When removing the quarter window from the body opening make sure that the attaching pins are clear of the outer body.
Remove the quarter window (2) from the body opening.

Remove the rear seat cushion. Refer to Rear Seat Cushion Replacement in Seats.
Remove the rear seat back. Refer to Rear Seat Back Replacement in Seats.
Remove the door sill plate. Refer to Door Sill Plate Replacement .

Remove the 3 quarter trim panel retaining screws (1).
Starting at the lower edge of the trim panel and moving alternately clockwise and counterclockwise, pull outward on the trim panel to disengage the eight rear quarter trim panel attaching clips (2).
Remove the quarter trim panel from the vehicle.
Remove the 4 radio speaker grille speed clips (1), securing the speaker grille.
Remove the speaker grille (2).
Remove the rear quarter trim panel insulator (1), from the back of the quarter trim assembly (2).
Remove 7 rear quarter trim panel armrest retaining clips (1).
Remove 7 rear quarter trim panel armrest retaining nuts (2).
Gently pry the quarter trim panel armrest insert assembly (3), away from the rear quarter trim panel and remove.

You mite look for a video on youtube !

Same place you fill for the front washer fluid ! Your fronts work but not the rear ? There are to washer pump motors on the washer fluid bottle , one for the front an one for the back . Rubber hose goes all the way to the back . If that hose has failed ,to replace it you basically have to pull out your vehicles interior .
Rear Window Washer Hose Replacement - Pump to Endgate
Removal Procedure

1. Remove the left front seat. Refer to Bucket Seat Replacement in Seats.
2. Remove the rear seat. Refer to Rear Seat Replacement in Seats.
3. Remove the endgate/liftgate door sill plate. Refer to Rear Floor Rear Trim Plate Replacement or Liftgate Door Sill Plate Replacement in Interior Trim.
4. Remove the left front and left rear door sill plates. Refer to Door Sill Plate Replacement in Interior Trim.
5. Remove the left body side trim panel. Refer to Body Side Trim Panel Replacement in Interior Trim.
6. Remove the left hinge pillar trim panel. Refer to Body Hinge Pillar Trim Panel Replacement - Left Side in Interior Trim.
7. Fold over the left side of the carpet to allow access to the body harness. Refer to Front Floor Mat/Carpet Replacement and Rear Floor Panel Carpet Replacement in Interior Trim.

Disconnect the washer hose connection (1) from the body harness (2) at the endgate. Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement in Engine Controls.
Disconnect the hose (1) from the rear washer pump. Install a plug to the rear washer pump nozzle to prevent washer fluid loss. Push the hose grommet (2) in through the bulkhead.
Pull the washer hose (1) into the vehicle though the bulkhead. Cut the old washer hose off where it enters the body wiring harness (2). Remove the hose end from the vehicle
Or it could be the pump , they go bad . switch the hoses from one pump to the other an see if you get washer fluid at the back ,if you do the pump is bad ,if not the hose or the spray nozzle is clogged . You probably will need to pull the washer fluid bottle to see both pumps

It is located behind the right rear quarter panel , In the back right of the interior !
Remove the right rear quarter trim panel. Refer to Rear Quarter Trim Panel Replacement - Right Side in Interior Trim.
Removal Procedure

1. Remove the rear seat. Refer to Rear Number 2 Seat Replacement or Rear Number 2 50-50 Seat Replacement in Seats.
2. Remove the Third Pillar trim panel. Refer to Third Pillar Trim Replacement .
3. Remove the garnish molding. Refer to Body Rear Corner Garnish Molding Replacement .
4. Remove the door sill plate. Refer to Liftgate Door Sill Plate Replacement .
5. Remove the quarter panel trim screws.

A lot involved in this but not to difficult !

1. Remove the rear door sill trim plate. Refer to Front Side Door Sill Plate Replacement or to Rear Side Door Sill Plate Replacement .
2. Remove the lower rear seat belt cover and bolt.
3. Remove the trim panel from the vehicle.

Remove the sill plate. Firmly pull the sill plate up and out from the retainers.
Remove the sill plate from the vehicle. Start from the front of the door sill. Use a flat-bladed tool in order to pry the door sill plate.
Rear Side Door Sill Trim Plate Replacement
Use a flat-bladed tool in order to pry the door sill plate. Remove the sill plate from the vehicle.
Body Rear Corner Garnish Molding Replacement
Remove the rear upper garnish molding. Refer to Rear Upper Garnish Molding Replacement .
Pull down on the upper corners of the garnish molding in order to disengage the retaining clips. Pull in order to disengage the remaining retaining clips. Remove the rear corner garnish molding from the vehicle. Inspect the rear corner garnish molding for broken or missing retaining clips. Replace the retaining clips as needed.
Good Luck ! Fun job !!!!!

Section 01-05: Trim, Interior 1998 Windstar Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/22/1999 Trim Panel, Door Front
Removal

1. Remove door latch cover by prying from top edge and pulling trim free of retaining clips and sliding trim away from latch.
   

1. Remove portion of armrest containing door lock switch and window regulator control switch (14529) by pulling straight up.
   

1. Remove rear view outside mirror mounting hole cover assembly by prying at top and pulling upward to release double-sided clip.
   
   
   Trim Panel
   
   
   
   
   
   Item Part Number Description 1 23942 Front Door Trim Panel 2 56908-S58 Screw (1 Req'd), Right Door 56906-S58 Screw (1 Req'd), Left Door 3 18B978 Radio Speaker Grille Name Plate 4 56911-S58 Screw (1 Req'd) 5 17D720 Cover Assembly Rear View Outside Mirror Mounting Hole

1. Remove screw attaching front door trim panel (23942) to front door (20124) under switch plate.
   

1. Remove two screws located at bottom of front door trim panel.
   

1. Disconnect the door lock switch (14028) and window regulator control switch electrical connectors.
   

1. Remove door window regulator handle if equipped by unsnapping and pivoting away the handle cover from base to expose retaining screw. Remove screw from the door window regulator handle.
   

1. Pull front door trim panel from the top to release hooks from front door .
   

1. Remove front door trim panel.
   

Installation

1. Replace any bent or damaged fasteners.
   

1. Follow removal procedure in reverse order.
   

Body Side
Removal

1. Remove door handle retaining clip by sliding a shop towel between handle and door trim. With tension on the cloth, pull one end of the cloth so it slides between the handle and the door trim. If handle does not come out, reverse direction.
   

1. Unfasten 13 christmas tree fasteners using double-acting spring-loaded trim removal tool and pull body side trim panel from body side door.
   

1. Remove forward and rearward mating sections from under window trim.
   

Installation

1. Replace all christmas tree fasteners.
   

1. Follow removal procedure in reverse order.
   

1. For installation of handle, install clip to handle, then push handle onto shaft to snap in place.
   
   
   
   
   

Back
Removal

1. Disconnect rear window defroster wires.
   

1. Remove the liftgate window garnish moulding as described.
   

1. Remove screws attaching liftgate handle to liftgate and liftgate inside trim panel.
   

1. Using Rotunda Windshield and Moulding Trim Removal Kit 107-R0401 or equivalent, pry pushpins retaining liftgate trim from the liftgate.
   

1. Remove liftgate trim.
   

Installation

1. Follow removal procedure in reverse order.
   
   
   Liftgate
   
   
   
   
   

Please don't forget to rate! Thank you!

Removal & Installation

The door-to-body mounting

Detach the door wiring from the connector

This is a two person operation.

1. Remove the two door check-to-body retaining screws.
   

WARNING

Cover the end of the check strap to prevent possible paint damage.

1. On the rear doors, remove the rear door trim panel, detach the electrical connectors from the components (if equipped) and remove the wiring harness from rear door.
   
2. On the driver's side front door, disconnect the window regulator wiring, if so equipped, by removing the wire connector cover, loosening the screw and separating the connector halves.
   
3. On the passenger side front door, remove the rubber harness protector from the body to reveal the electrical connectors. Detach the two electrical connectors.
   
4. If the door is to be replaced, transfer the following components to the new door if in usable condition:
   
   • Door trim panel
     
   • Watershield
     
   • Outside mouldings
     
   • Trim clips
     
   • Window regulator
     
   • Door latch components.
     
5. Remove the hinge retaining screws and nuts from the door and remove the door.
   

To install:

1. Position the door onto the hinges and hand tighten the screws.
   
2. Align the door and tighten the screws to 19-25 ft. lbs. (25-35 Nm).
   
3. If removed, install the wiring harness to the rear doors.
   
4. Attach the electrical connectors to the door panel.
   
5. Install the door panel(s).
   

// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 31; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos';

door panel must come off.

go here for villager help

http://groups.yahoo.com/group/villagerquest/

Section 01-05: Trim, Interior 1997 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door
Front
Removal

1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
   

1. CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
   Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942).
   
   
   
   
   

1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel.
   

1. Pull the shop rag back and forth to release the window regulator handle clip.
   
   
   
   
   

1. Remove the three cover caps and front door trim panel screws.
   

1. Remove the one front door trim panel capped screw from the door pull handle.
   

1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
   

1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124).
   

1. Remove the front door trim panel.
   

Installation
To install, reverse the removal procedure. Body Side
Removal

1. Gently pry loose the body side door latch handle bezel and remove it.
   

1. Slide a suitable tool behind each of the retainers and twist the tool to disengage the body side door trim panel from the body side door (24622).
   
   
   
   
   

Installation
To install, reverse the removal procedure. Door Electrical Connections
Removal and Installation
Refer to Section 01-11 for Power Window, Section 01-09 for Power Mirror, or Section 01-14B for Power Locks. Watershield
Removal

1. Remove the Front Door Trim Panel . Refer to the removal procedure in this section.
   

1. Remove the front door watershield by carefully detaching it from the adhesive.
   

Installation

1. Install the front door watershield in the proper position and press firmly at the adhesive areas. If necessary, use additional adhesive to ensure an adequate seal.
   

1. Install the Front Door Trim Panel . Refer to the installation procedure in this section.
   

Check for broken wires in the harness in the door jamb the wires are known to break in this location quite often from flexing ...if not the ground is probably on the drivers side behind the plastic on the kick panel up near the dash..

I assume that the entire handle unit is loose in the body work of the door.
The interior door trim will need to be removed to access the inside of the door to fix the loose handle.

Do not attempt his yourself unless you have some experience in this area.
Take the vehicle to the nearest reputable auto body repair shop and they can easily fix it for you. There could be a breakage on the retaining system on the handle or the retainers may just need tightening.

Typically door handles which have not been subject to damage or abuse will not usually loosen like this. It's possible the door was damaged and the panel repaired and repainted at some stage. If so the door handle may have been removed and refitted in a sloppy manner.

the door handle is either broke or a part of it has slipped loose, either way, you'll have to remove the inner door panel to get to it, this is not difficult, a few screws and the panel is retained by push in type plugs that can be pryed loose. the entire door latch assy is held in by screws and is serviced by replacement, the difficulty come with very tight area to work in, and is irritating and time consuming, if you are not good with tools i'd suggest a good mechanic or body shop. always get a quote!!