Question about 2004 Nissan Maxima

1 Answer

Where is the cam position sensor located on a 2004

Where is the cam position sensor located on a 2002 nissan maxima

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 145 Answers

Here is where is the cam position sensor located on a 2004 - 7353049.jpg

Posted on Jul 02, 2009

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: WHERE IS THE CAM POSITION SENSOR LOCATED ON A 2004 NISSAN MAXIMA

WHEN YOU STAND ON THE FRONT OF THE CAR YOU ONE IS RIGHT BELOW OF THE INTAKE WHICH IS BANK 2 OR THE ONE CLOSE TO FIREWALL , BANK 1 ONE IS ON SAME SIDE NEXT TO THE RADIATOR BUT THEY BOTH ON THE CAM RIGHT SIDE OF THE ENGINE, THE EASIEST WAY TO IDENTIFY THEM IS THAT THEIR CONNECTOR IS GREEN, ONCE YOU LOCATE THEM THE CLIP NEEDS TO BE PUSHED DOWN TOWARD THE SENSOR FOR THE CONNECTOR TO BE RELEASED, ONCE YOU REMOVE THE CONNECTOR THERE WILL BE ONLY A 10MM SCREW HOLDING THE SENSOR PULL IT OUT , THE SAME SETTING THE NEW ONE PUSH IT ALL THE WAY IN , THIGHT THE 10MM SCREW, CONNECT IT BACK AND YOU'RE DONE,BUT FOR THE ONE ON THE BACK SOMETIMES MIGHT BE NECESARY FOR YOU TO TAKE THE INTAKE OFF....HOPEFULLY IS NOT YOUR CASE....



Good luck!!! and if you need the crank for hard starting on hot/warm, it is located on the botton middle section on the transmission is the only cable that goes down to a small piece of metal and it is held by a 10mm screw only to protect the sensor, you will se the sensor once you remove that small about 6-8 inches piece of metal. Then you'll be able to unescrew the 10mm screw that holds the crank position sensor. when you pull it off you'll be able to see the fly wheel inside the transmission...



you all enjoy your rides out htere!!!

Posted on Jul 01, 2009

  • 56 Answers

SOURCE: Hello, Where is the Cam

3.5litre V6 Front wheel drive, the cam position sensor is in the back of the cylinder head above the transmission. bank one is the front bank, nearest to the grill. the cam sensor is held into the head with a 10mm bolt, has one wireing connector with 3 wires in it. the sensor is sort of round with a leg off one side for the bolt the secure.
may need to remove the engine cover to see it. it is held down with allen key bolts.

Posted on Mar 26, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the cam position sensor on a 2003 nissan maxima and is it hard to replace?


The camshaft sensor is positioned on the end of the cylinder head.

___________________
Allobd2.com

Jun 19, 2012 | Cars & Trucks

1 Answer

Where is the rear bank camshaft position sensor located on a 2004 Nissan Maxima DOHC 6 cylinder?


Both cam sensors are on the rear of the cylinder heads. They are located in the same place on each head. The only difference in the two sensors is one has a straight connector and the other has an angled connector because of other things that are in the way, (see diagram)


dttech_172.gif

Aug 22, 2011 | 2004 Nissan Maxima

1 Answer

Hello, Where is the Cam position sensor located on a 2004 Nissan maxima bank 1 located?


3.5litre V6 Front wheel drive, the cam position sensor is in the back of the cylinder head above the transmission. bank one is the front bank, nearest to the grill. the cam sensor is held into the head with a 10mm bolt, has one wireing connector with 3 wires in it. the sensor is sort of round with a leg off one side for the bolt the secure.
may need to remove the engine cover to see it. it is held down with allen key bolts.

Mar 25, 2011 | 2004 Nissan Maxima

1 Answer

I have a 2002 Nissan Maxima and the check engine light has come on. One of the codes being reported is P0021. It seems to be related to a cam position sensor. Does anyone know the location of the sensor?...


Here is the location....

http://www.courtesyparts.com/maxima-parts-a33b-2000-2003/genuine-nissan-parts/engine-electrical/221-distributor/-c-1956_1957_1988_1990.html

Jul 08, 2010 | 2002 Nissan Maxima

2 Answers

What does the cam censor control on a Nissan 2004 Maxima and where is it located?


where is the crank shaft sensor located on 2004 nissan maxima 3,5sl

Apr 13, 2010 | 2004 Nissan Maxima

1 Answer

Location of cam senswer on my 2003 nissan maxima 2.5 trying to find it.Can u help me locate it with photograph


CAM SENSOR IS ON ENGINE DRIVERS SIDE RIGHT BESIDE FUEL PRESSUE REGULATER FOLLOW STEEL FUEL LINE LOOK RIGHT BEHIND REGULATER AND YOU WILL SEE IT

Feb 13, 2010 | 2003 Nissan Maxima

2 Answers

Where is the cam position sensor on a 2000 Maxima GXE


there are 2 sensors, they are located under the intake manifold which must be removed to access them

Jan 25, 2010 | 2004 Nissan Maxima

4 Answers

WHERE IS THE CAM POSITION SENSOR LOCATED ON A 2004 NISSAN MAXIMA


WHEN YOU STAND ON THE FRONT OF THE CAR YOU ONE IS RIGHT BELOW OF THE INTAKE WHICH IS BANK 2 OR THE ONE CLOSE TO FIREWALL , BANK 1 ONE IS ON SAME SIDE NEXT TO THE RADIATOR BUT THEY BOTH ON THE CAM RIGHT SIDE OF THE ENGINE, THE EASIEST WAY TO IDENTIFY THEM IS THAT THEIR CONNECTOR IS GREEN, ONCE YOU LOCATE THEM THE CLIP NEEDS TO BE PUSHED DOWN TOWARD THE SENSOR FOR THE CONNECTOR TO BE RELEASED, ONCE YOU REMOVE THE CONNECTOR THERE WILL BE ONLY A 10MM SCREW HOLDING THE SENSOR PULL IT OUT , THE SAME SETTING THE NEW ONE PUSH IT ALL THE WAY IN , THIGHT THE 10MM SCREW, CONNECT IT BACK AND YOU'RE DONE,BUT FOR THE ONE ON THE BACK SOMETIMES MIGHT BE NECESARY FOR YOU TO TAKE THE INTAKE OFF....HOPEFULLY IS NOT YOUR CASE....



Good luck!!! and if you need the crank for hard starting on hot/warm, it is located on the botton middle section on the transmission is the only cable that goes down to a small piece of metal and it is held by a 10mm screw only to protect the sensor, you will se the sensor once you remove that small about 6-8 inches piece of metal. Then you'll be able to unescrew the 10mm screw that holds the crank position sensor. when you pull it off you'll be able to see the fly wheel inside the transmission...



you all enjoy your rides out htere!!!

Feb 25, 2009 | 2004 Nissan Maxima

Not finding what you are looking for?
2004 Nissan Maxima Logo

897 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...