Question about 2004 Isuzu Ascender

2 Answers

My Ascender keeps burning its rear lights, and the license plate lights don't work, evrn though they are new.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 33 Answers

You have a wire shorted out some where - need to trace wires and find one that is broken or cut- also test out the light switch relay ( these do go bad from time to time )

Posted on Jul 02, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

There was a recall or technical bulletin issued by Isuzu on this in 2005. I believe the wire gauge was too small for the electric load or something about a relay....

Posted on Dec 01, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2005 matrix keeps blowing 15amp rear running light fuse every time light get turned on all other lights work fine.whats causing this?


fuses blow because of dead shorts or excess current draw
to blow a 15 amp fuse indicates a dead short
by disconnecting the rear lights , the problem is in something else you have replaced
could be a problem in the head light wiring

Feb 05, 2016 | 2005 Toyota Matrix XR

1 Answer

My rear wiper, defroster and licence plate lights stopped working on my 2007 suzuki swift but when I open the rear hatch the licence plate lights come on . Any ideas what's wrong?bad ground?


[PDF]Wiring Diagram.pdf - Ken Gilbert

ken-gilbert.com/wrx/mans/99.../Wiring%20Diagram.pdf
Each connector number shown in the wiring dia- ... Rear defogger cord (Ground). Fuel tank cord,. Roof cord, ... circuit. Then check the switch, relay, fuse, ground, etc. 4. .....Rear wiper motor. Rear wiper ... License plate light RH. Tail light LH.

#? license plate light - Circuit Wiring Diagrams

circuitswiring.com/tag/license-plate-light/
2008 Volkswagen Newbeetle Main Fuse Box Diagram 2008 Volkswagen Newbeetle ...Parts: rear window defogger, shift lock, battery positive voltage, interior light, A/C clutch, ... brake light, daytime driving light, wiper and washer system, vacan, fuel pump, central ... 1997 Suzuki Geo Tracker Left Dash Fuse Box Diagram.

#? license plate light - Circuit Wiring Diagrams - Page 3

circuitswiring.com/tag/license-plate-light/page/3/
Audi A4 Engine Fuse Box Diagram Audi A4 Engine Fuse Box Map Fuse Panel ... mirror control, wiper, washer, horn, brake light, cruise control, heated rear window, ... 2003Suzuki Aerio Dash Fuse Box Diagram 2003 Suzuki Aerio Dash Fuse Box ... rear defroster, fuel injection controller, radio, A/T controller, hazard light, ...

Jan 05, 2016 | Suzuki Cars & Trucks

1 Answer

License plate light


The licence plate doesn't have a fuse, it comes on when you put your lights on, if you have your park lights on and the plate light isn't working then generally it's just a bulb, see what you can find, cheers good luck

Feb 19, 2014 | 2002 Mitsubishi Eclipse

1 Answer

Tag light is not working. is there a fuse that will get the light turned back on?


The fuse labeled REAR PARK LP 15A in the right instrument panel fuse box powers the rear park lamps, and the tag lamps. If your rear park lamps are working then you most likely need to replace the tag lamps (bulbs). Use the following procedure to replace the lamps.

To Remove:
  1. Remove the two mounting screws from the license plate lamp.
  2. Remove the license plate lamp from the rear bumper fascia.
  3. Remove the license plate lamp socket by turning it counterclockwise.
To Install:
  1. Install the license plate lamp socket by turning it clockwise.
  2. Position the license plate lamp to the rear bumper fascia.
  3. Install the license plate lamp mounting screws.

Feb 17, 2011 | 2004 Chevrolet Impala

1 Answer

Rear license plate lights burned out and can't remove or replace them. Screws won't back out of assembly. 1997 Buick LeSabre


If i remember correctly the entire rear light assembly must be remove in order to access these bulbs. This is true if the license plate is on the trunk. If this is the case then there are nuts on the inside of the trunk that must be removed.

Jun 30, 2009 | 1998 Buick LeSabre

1 Answer

License plate light replacement


The license plate lights are in the ledge above the license plate. 2 screws keep the lens cover in place. Remove the screws, and the cover comes off. Just pull the lamp out (wedge base) and replace.

Apr 13, 2009 | 2002 Chevrolet TrailBlazer

1 Answer

1993 Toyota Camry - Tail lights don't work / brake lights do?


Dude the wires at the trunk inside break from opening and closing. you must peel back the wires covering to expose and fix these wires.

Mar 24, 2009 | 1993 Toyota Camry V6

1 Answer

Burned out license plate bulb


open trunk,

remove felt liner from rear of trunk, (liner directly behind rear lights in side trunk) should be 4 plastic Phillips head screws. Loosing screws, then slowly peel liner away. You will see 3 nuts on each side, removing these nuts will loosing the rear light lenses, so you can pull the lense away from the body from the out side to gain access to the license plate bulbs. Re-install in reverse order. While in there I would recommend replacing your brake light and reverse light bulb. Hey your already in there might as well do a little preventive maintance.

Dec 12, 2008 | 1995 Lexus ES 300

1 Answer

License Plate lamp burned out.


you'll see the lights plugged in under rear bmper. grasp the light plug,twist counter clkwise 1/4 turn, pull out plug, pull bulb strait out, push new bulb back in.

Nov 11, 2008 | 1998 GMC Suburban

2 Answers

License Plate Lights


Probably not... For some reason license plate light wiring and sockets are VERY prone to corrosion. Make sure to check the light sockets and try to get to the wiring close to them, your problem is more than likely very close to the lights.

Aug 12, 2008 | 2005 GMC Sierra

Not finding what you are looking for?
2004 Isuzu Ascender Logo

Related Topics:

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...