I have a 95 Honda Accord four-door. Drivers door power window will not work. I have replaced the motor and I have taken apart the master window switch and cleaned the terminals. Looking for the relay fuse for the drivers window. All the other windows and sunroof work fine.

if no switch operates the window will be the motor
or broken wire across the door hinge

can you hear a motor click or sound from the door
if not
take the door card off and hot wire the window motor
Part2 How to fix replace install broken window regulator motor Honda...

Power Windows Not Working - Repair Power Windows

www.popularmechanics.com/cars/how-to/a69/1272371/

Another toll-booth, another mile--or at least it seems as if the tollbooths come every ... The most common power window mechanism is pretty basic. ... If the driver's door switch won't open the right rear door, but the switch in the ... direct from the battery positive terminal to the positive side of the motor to see if it comes alive.

Power Windows not working - CarGurus

www.cargurus.com > Questions > Honda > Accord

CarGurusOct 9, 2012 - I have a 2007 Honda Accord the driverside window works but other 3windows dont, but when u hit the master switch on drivers door to try to ...

I can only operate one of three power windows - CarGurus

www.cargurus.com > Questions > Chevrolet > Prizm

CarGurusApr 28, 2013 - Drivers side power window works only. Had a mechanic ... windowsnot working either. ... Already replaced it. all switches showing getting power but don'twork. ... Are you certain that the other three window motors are good?

Why Do My Power Windows Sometimes Stop Working ...

Use a test light and check if getting power on that hot wire at the connection to motor. Check it back to the fuse panel by holding the down button if window up and vice-versa. Since motor was replaced, You know it's good but no power to it. It's got to be a broken wire or unplugged somewhere. Find that spot with a test light. ALL you can do is test it till you find that broken spot.

CHECK POWER WINDOW 20 AMP FUSE.ALL FOUR WINDOWS HAS A INDIVIDUAL FUSE YOU HAVE 4 FUSES. ONE FOR EACH WINDOW. CHECK FRONT LEFT FUSE OR FRONT RIGHT FUSE.

Looks like you are going to have to take the door apart for inspection. There is a good chance that the half moon jumped a couple of teeth and that the mechanicals between the electric motor and the scissor window raising mechanism is out of sequence. Once the door panel is taken apart, it is a rather simple task, to loosen the scissors, raising the window by hand, and re-tightening after you have shifted the whole assembly a couple of teeth. Remember not to place the window up to the exact top spot, but rather a little higher ( so that the window tries to keep going after it is fully up). This in order to insure a tight rain / road noise seal, the motor will recognize the extra load, and will stop working when the window glass is tight against the top frame.

First I would check the power window fuse. Do the windows not work from either the drivers door or the other doors? Make sure the window lock out is not on on the drivers door too!

if you try to move the windows with the other switches on the other doors and the windows still do not work then replace the drivers door master switch. the circuit for all windows runs through that switch

possibly your power window regulator is out. basically check the fuses first to make sure you have not blown that, if it is good, then you can order a new window regulator from the dealer or online @ autopartswarehouse.com. to replace the window regulator you will need to will need to remove the door panel, start with the screws on the handle and the arm rest, covered with a plastic cap. the door panel which can be pryed from the bottom with a flat blade screw driver or flat pry bar, it will make a snapping sound. three bolts on the regulator 4 bolts on the window tracks and 2 bolts securing the window, re assemble as you have taken apart, Good Luck!!

look for power windows relay.

Pull off door panel speaker and switches. lower the window to where you see the two or four 10millimeter that connect scissor mechanism to the window. Prop window all the way up and put a door stopper to prevent the window from falling down. Unbolt window motor, unplug window motor, and unbolt eveything else in the door. Pull it all down and out through the bottom largest whole, lay flat on ground the entire indoor mechanism, out where you can see it on the floor. Take a pic with camera, and proceed to swapping regulator, intallation is same as removal. Good Luck