What tolls are needed to remove tail light and brake light bulb
SOURCE: Tail light removal
There is also a screw on the bottom of the light housing. You access this screw by laying on your back and reaching up behind the bumper assembly. You may also need to take one screw off the bumper mount near the tail light. This makes it easier to remove the old light housing.
SOURCE: Tail/brake light bulb replacement 2004 Olds Alero
In the trunk, in the rear corners, you'll see some plastic "caps" with tabs on them, similar to wing nuts. Remove those, and the taillight comes right off the back of the car. That will allow you to replace the bulbs.
SOURCE: removing tail light
Drop the tailgate - there are two torx style bolts holding the lens assembly in place. Remove both, then with some gentle force, pull the lens assembly straight back(there are two self seating plastic bolts that hold the assembly into the truck frame, towards the cab).
Once undone, there is a strip of three bulbs on one wired base, and that base is screwed to the lens assembly (4 phillips screws). Unscrew those, and the lens assembly is free from the base. You can then remove the bulbs, insert new ones, and reverse the process. Good luck.
SOURCE: Tail Light in 2004 Beetle
If you need to replace your tail light bulb, first remove the cover (it's round) from the inside of your trunk. There will be a black knob that needs to be unscrewed totally to release the back light casing. The screw is spring loaded so it is not going to fall. Be sure to hold on to the black knob. If you drop it you can retrieve it, but it's best to not drop it. Next pry the light casing from the fender with a knife or some other sturdy object. It is best to pry the light out from the line that runs from the light to the hatchback door. Don't be afraid, it takes a little force to pull out. After you pull out casing, you'll find two light switches. The one with one filament is for the turn signals and the one with two filaments is for the break light. Turn the light switch counter clockwise and remove. Switch out light bulb with new one (AutoZone has them for about $5.00 - package of 2). Replace every thing back as you uninstalled it. It is recommended that you replace all bulbs, that way it you don't have to do it again later when they go out. It'll save you the time and hassle of doing this again. Hope this will help anyone so print and save in your manual for later use.
SOURCE: how to access brake tail light to change
Tail light replacement is not as hard as it seems.
Tools needed:flat head screwdriver and a deep 5/32 socket(a pair of pliers will work).
Step 1: open trunk and pull back truck liner at tail light.There is a small button clip on liner.Use screwdriver to pop up the center of button clip,pull clip out of hole.
Step 2:You will see a black wire attached to the body of car with 2 white clips.Use screwdriver to pop clips off of studs.
Step 3:Remove the nuts from the studs and pull tail light assembly straight back away from car.The outer side of the light just snaps in and out of place.
Step 4:Turn light socket counter clockwise 1/3 turn and pull out.
Step 5:Pull bad bulb straight out and replace.Reverse steps to reassemble.
The
process for replacing tail light bulbs is the same in all models. If
you have a burnt-out tail light bulb, you may need to replace the
brake light, the reverse light or the turn signal. The procedure to
replace each of the bulbs is the same.
Instructions
1.
Open the Hummer's rear swing gate. This will expose the edge of the
vehicle's tail light assembly. You'll see two small Phillips head
screws that hold the tail light assembly in place. Put on your
gloves.
2.
Remove the two screws from the tail light assembly. Pull the tail
light out and inspect the back for two bulbs. The top bulb is the
brake light and turn signal. The bottom bulb is the reverse bulb.
Determine which bulb you need to replace.
4Push
the replacement bulb into its socket firmly. Insert the socket back
into the tail light. Turn it clockwise to secure it in place.
5Place
the tail light into its cradle. Hold it with one hand and replace
the Phillips head screws with the other.
55 views
Usually answered in minutes!
×