Question about 2005 Chevrolet Aveo

1 Answer

The crankshaft sprocket bolt of my 2004 Chevy Optra loosened. What is the required torque tightness of this bolt? Would you recommend that I apply any grease on the bolt threads & washers before installation or Loctite Thread Locker Adhesive instead?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 701 Answers

Hello dickiesantia: My name is Roger and I will help you. The correct torque for the crankshaft bolt is 89 ft.lb. As far as lubricant for the threads use none. You can use thread lock on the bolt. Since it has come loose I would defiantly use thread lock. Should you need any further help please just ask. Please rate the quality of this answer as this way we know you received the correct answer. Thank You for using Fix Ya. Roger

Posted on Jul 01, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Need timing gear marks for 2004 Kia Sadona 3.5L engine



Removal & Installation

3.5L Engine

  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Record the radio anti theft code data.
  3. Remove or disconnect the following:

    Negative battery cable Engine cover Accessory drive belts Idler pulley Crankshaft pulley Power steering pump pulley Belt tensioner pulley Upper and lower timing belt covers
  4. Support the engine with a floor jack and remove the engine mount.
  5. Rotate the engine to align the camshaft sprocket timing marks with the cylinder head cover timing marks.

    0996b43f8022cb71.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt routing and timing marks-3.5L Engine

  6. Remove or disconnect the following:

    Auto tensioner Timing belt

    0996b43f8022cb72.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt and related components-3.5L Engine


To install:
  1. Ensure that the engine is set to Top Dead Center (TDC).
  2. Prepare the auto tensioner for installation by compressing it in a vise and installing a retaining pin.
  3. Install the timing belt in the following order:
    1. Crankshaft sprocket
    2. Idler pulley
    3. Left bank exhaust camshaft sprocket
    4. Left bank intake camshaft sprocket
    5. Water pump pulley
    6. Right bank intake camshaft sprocket
    7. Right bank exhaust camshaft sprocket
    8. Tensioner pulley

  4. Install the auto tensioner. Do not remove the retaining pin at this time.
  5. Check that the crankshaft and camshaft timing marks are aligned correctly.
  6. Rotate the crankshaft 1 / 4 turn Counterclockwise .
  7. Rotate the crankshaft 1 / 4 turn Clockwise to return the engine to TDC.
  8. Loosen the tensioner pulley center bolt.
  9. Apply 44 inch lbs. (5 Nm) torque to the tensioner pulley as shown and tighten the center bolt to 32-41 ft. lbs. (43-55 Nm).

    0996b43f8022cb73.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Adjusting the tensioner pulley-3.5L Engine

  10. Remove the auto tensioner retaining pin.
  11. Rotate the crankshaft 2 revolutions Clockwise , then wait 5 minutes for the auto tensioner to adjust.
  12. Measure the auto tensioner rod as shown. If the measurement is not 3.8-4.5 mm, then repeat the belt tensioning procedure.

    0996b43f8022cb74.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Measuring the auto tensioner rod-3.5L Engine

  13. When the auto tensioner measurement is correct, install or connect the following:

    Engine mount Upper and lower timing belt covers Belt tensioner pulley Power steering pump pulley Crankshaft pulley Idler pulley Accessory drive belts Engine cover Negative battery cable
  14. Reprogram the radio anti theft codes.

    Kia_Sedona_2002-2006
    Timing Chain, Sprockets, Front Cover & Seal

    Print


    Removal & Installation

    3.8L Engine

    1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
    2. Record the radio anti theft code data.
    3. Remove the engine from the vehicle.
    4. Remove the drive belt. Remove the power steering pump. Remove the air conditioning compressor.
    5. Remove the alternator. Remove the drive belt idler. Remove the drive belt tensioner. Remove the water pump pulley. Remove the intake manifold.
    6. Remove the connector bracket from the left cylinder head cover. Disconnect the right ignition coil connector, condenser connector and remove the bracket.
    7. Remove the left cylinder head cover retaining bolts. Remove the cylinder head cover from the engine.
    8. Remove the right cylinder head cover retaining bolts. Remove the cylinder head cover from the engine.
    9. Set the No. 1 cylinder to TDC on the compression stroke. Turn the crankshaft pulley and align its groove with the timing mark T of the lower timing chain cover.
    10. Check that the mark of the camshaft timing sprockets are in straight line positioning on the cylinder head surface. If not rotate the crankshaft 360 degrees. Do not rotate the engine counterclockwise.
    11. Remove the oil pan. Remove the crankshaft damper pulley. Remove the timing chain cover.
      NOTE Be careful not to damage the contact surfaces of the cylinder block, cylinder head and timing chain cover. Before removing the timing chain, mark the right and left timing chains with an identification mark based on the location of the sprocket because the identification mark on the chain for TDC can be erased.
    12. After compressing the timing chain tensioner, install a set pin. Remove the right cam to cam guide. Remove the right timing chain auto tensioner and timing chain tensioner arm.
    13. Remove the oil pump chain cover. Remove the oil pump chain tensioner assembly. Remove the oil pump chain guide. Remove the right timing chain.
    14. Remove the right timing chain guide. Remove the oil pump chain sprocket and oil pump chain. Remove the crankshaft sprocket, oil pump and camshaft drive gear.
    15. Remove the left cam to cam guide. Remove the left timing chain auto tensioner and timing chain tensioner arm. Remove the left timing chain.
    16. Remove the left timing chain guide. Remove the crankshaft sprocket and left camshaft drive. Remove the tensioner adapter assembly.

      0996b43f8020193b.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing chain and related components-3.8L Engine


    To install:
    1. Check the camshaft and crankshaft sprockets for wear and damage, replace as required.
    2. Inspect the tensioner arm and chain guide for wear and damage, replace as required.
    3. Check that the tensioner pin moves smoothly when the ratchet pawl is released with a thin rod.
    4. The key of the crankshaft should be aligned with the timing mark of the timing chain cover. This indicates that the piston is at TDC on the compression stroke.
    5. Install the tensioner adapter assembly. Install the crankshaft sprocket and left camshaft drive.
    6. Install the left timing chain guide and torque the retaining bolts 14-18 ft. lbs.
    7. Install the left timing chain. Be sure to install the chain with no slack between the camshaft and the crankshaft (crankshaft sprocket, timing chain guide, exhaust camshaft sprocket, intake camshaft sprocket). The timing mark of each sprocket should be matched with the timing mark (color ink) of the timing chain at installation of the timing chain.

      0996b43f80201924.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Left timing chain markings and installation: (D) exhaust camshaft sprocket (C) intake camshaft sprocket-3.8L Engine

    8. Install the left timing chain tensioner arm and torque the retaining bolts 14-16 ft. lbs.
    9. Install the left timing chain tensioner and torque the retaining bolts 7-9 ft. lbs.
    10. Install the left cam to cam guide and torque the retaining bolts 7-9 ft. lbs.
    11. Install the crankshaft sprocket, oil pump and right camshaft drive.
    12. Install the oil pump chain and oil pump sprocket. Torque the retaining bolt to 14-16 ft. lbs.
    13. Install the right timing chain guide. Torque the retaining bolts to 14-18 ft. lbs.
    14. Install the right timing chain. Be sure to install the chain with no slack between the camshaft and the crankshaft (crankshaft sprocket, intake camshaft sprocket, exhaust camshaft sprocket). The timing mark of each sprocket should be matched with the timing mark (color ink) of the timing chain at installation of the timing chain.

      0996b43f80201925.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Right timing chain markings and installation: (C) exhaust camshaft sprocket (B) intake camshaft sprocket-3.8L Engine

    15. Install the right timing chain tensioner arm. Torque the retaining bolts to 14-17 ft. lbs.
    16. Install the right timing chain auto tensioner. Torque the retaining bolts to 7-9 ft. lbs.
    17. Install the right cam to cam guide and torque the retaining bolts to 7-9 ft. lbs.
    18. Install the oil pump chain guide. Torque the retaining bolts to 7-9 ft. lbs.
    19. Install the oil pump tensioner assembly. Torque the retaining bolts to 7-9 ft. lbs.
    20. Pull out the pins on both the left and right hydraulic tensioners. Install the oil pump chain cover.
    21. Rotate the crankshaft two revolutions in the clockwise direction. Confirm the timing mark. Be sure to rotate the crankshaft in the clockwise direction.
    22. Apply sealant on the chain cover and on the cylinder head, cylinder block, and lower oil pan. Be sure these parts are free of engine oil and dirt.
      NOTE Before assembling the timing chain cover, the liquid sealant TB1217H should be applied on the gap between the cylinder head and block. The part must be assembled with five minutes after the sealant is applied.


      0996b43f80201926.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Sealant application (1 inch bead width)-3.8L Engine

    23. Apply sealant on the chain cover.
      NOTE The liquid sealant TB1217H should be applied on the gap between the cylinder head and block. The part must be assembled with five minutes after the sealant is applied.


      0996b43f80201927.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover sealant application-3.8L Engine

    24. Install a new gasket to the timing case cover.
      NOTE It is important that the dowel pins on the cylinder block and holes on the timing chain cover should be used as a reference in order to assemble the timing chain cover in the correct position.


      0996b43f80201928.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover gasket installation (A) gaskets-3.8L Engine

    25. Install the timing chain cover. Torque the retaining bolts in the proper sequence and to specification. The engine should not be started for at least thirty minutes after timing chain cover assembly.

      0996b43f80201929.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover bolt torque sequence and specification-3.8L Engine

    26. Install the timing case cover oil seal.
    27. Continue the installation in the reverse order of the removal procedure.

May 19, 2012 | 2004 Kia Sedona

1 Answer

How to position the timing belt crank shafts of 1997 mazda mpv


Raise and support the vehicle on jack stands. Remove the wheel on the passenger side of the vehicle using the drive ratchet and a socket. Remove the passenger side splash shield, using the drive ratchet and a 10mm socket. 2 Remove the accessory belt(s), using a wrench to loosen the tension. Unscrew the bolt from the crankshaft pulley, using the drive ratchet and a socket. Slide the crankshaft pulley and the timing belt guide washer directly behind it off the crankshaft.3 Remove all the 10mm bolts in the top and bottom timing belt covers. Remove the covers. The drive ratchet and a 10mm socket works well for this. 4 Push the crankshaft pulley on the crankshaft just enough to engage the keyway. Turn the crankshaft pulley clockwise until the timing mark on the top camshaft sprocket, which is marked with a line on the sprocket with a number 1 next to it, is lined up with the pointer straight up on top of the cover to the rear of the sprocket. Once the top mark is lined up, the crankshaft pulley's semi-circle mark should be lined up with the triangular pointer on the block. The marks on the crankshaft pulley should be straight up and the keyway should also be straight up. Remove the crankshaft pulley. 5 Loosen the tensioner bolt with a wrench, pull the tensioner to the left, away from the belt and loosely tighten the bolt to hold it in place. Remove the timing belt. 6 Install the timing belt counter-clockwise starting at the crankshaft pulley and move upward over the outside the water pump, on the inside the guide pulley and over the top of the camshaft, ending on the inside the tensioner. The main thing when installing a timing belt is to ensure the belt is as tight as possible opposite the tensioner. Get the belt tight between the crank sprocket and the cam sprocket so the tensioner can take out all the slack without moving the timing marks.7 Loosen the tensioner bolt and allow the tensioner to apply pressure to the belt. Use your hand to apply a slight pressure to the tensioner toward the belt and tighten the tensioner bolt. Check the belt tension to ensure it is not too tight or too loose. Check the timing marks again to ensure they still align. If the timing marks are not lined up, loosen the tensioner, move it back and repeat the last procedure over again until the belt is tensioned properly with no misalignment of the timing marks. 8 Install the crankshaft pulley temporarily and turn the pulley two complete revolutions, once again aligning the mark on the crankshaft pulley. Ensure the timing mark is still lined up perfectly on the camshaft sprocket. Reinstall the remaining parts in reverse order of removal

Oct 14, 2011 | 1997 Mazda MPV

1 Answer

Need directions on how to install a timing chain on a 2002 Saturn L series 2.2 liter along with the allignment marks for the intake and exhaust cams


To Install:
  1. Install or connect the following:
    • Timing chain drive sprocket to crankshaft
      1. Rotate the crank so the mark on the sprocket is at the 5 o'clock position
  2. Assemble chain to the intake camshaft sprocket alignment copper link to the "INT" diamond timing mark on the camshaft sprocket sat_car_22_tmng-chn_pos.gif

    NOTE: When lowering the timing chain rotate the assembly 90° to allow the chain to fall between the cylinder block bosses then rotate the assembly back so the camshaft sprocket is facing forward.
    sat_car_22_tmng-c_hsng_opng.gif

  3. Lower the assembly through the chain housing opening on top of the cylinder head. Use care to ensure that the chain goes around both sides of the cylinder block bosses NOTE: The crankshaft sprocket timing mark will be at approximately the 5 o'clock position.
  4. Route chain around crankshaft sprocket and align silver link to the timing mark sat_car_22_set_tdc.gif

    NOTE: The camshaft sprocket bolts are not reusable; they are torque-to-yield and must be discarded to prevent premature failure.
  5. Install or connect the following:
    • Intake camshaft sprocket loosely onto the intake camshaft then install the new camshaft sprocket bolt finger tight NOTE: It is not necessary to align the sprocket-to-camshaft offset notch at this time.
    • Adjustable timing chain guide through the opening on top of the cylinder head then install the chain guide bolt; torque to 89 lb-in. (10 Nm) sat_car_22_ajst_tmng-ch_guid.gif

      sat_car_22_cm-shft_sprkt_blts.gif

    • Exhaust camshaft sprocket loosely onto the exhaust camshaft with the timing mark on the sprocket aligned with the silver link then install a new camshaft sprocket bolt finger tight
    NOTE: It is not necessary to align the sprocket-to-camshaft offset notch at this time.
    NOTE: The camshaft sprocket bolts are not reusable; they are torque-to-yield and must be discarded to prevent premature failure.
  6. Align the camshaft sprocket-to-camshaft then tighten the camshaft bolt using the following procedure: sat_car_22_crnk_tmng-c_mrk.gif

    NOTE: Do not rotate either camshaft more than 1/2 turn in either direction with the crankshaft at Top Dead Center (TDC). To do so may cause valve to piston contact resulting in a damaged valve and/or a damaged piston.
    • Ensure that the sprocket timing mark is at the 5 o'clock position
    • Rotate the intake camshaft using a 24mm wrench on the flats of the camshaft until the sprocket-to-camshaft alignment notch seats
    • When the sprocket seats on the camshaft tighten the sprocket bolt finger tight
    • Rotate exhaust camshaft using a 24mm wrench on the flats of the camshaft until the sprocket-to-camshaft alignment notch seats
    • When the sprocket seats on the camshaft tighten the sprocket bolt finger tight
  7. Verify that all colored links are aligned with the appropriate marks on the camshaft and crankshaft sprockets NOTE: If they are not repeat steps 1C through 4.
  8. Install the fixed timing chain guide and bolts; torque to 89 lb-in. (10 Nm)
  9. Install the fixed timing chain guide bolt access hole plug; torque to 30 lb-ft. (40 Nm)
  10. Install upper timing chain guide and bolts; torque to 89 lb-in. (10 Nm) NOTE: Use a 24mm wrench to support the camshaft while applying torque to the camshaft sprocket bolt. Do not torque the camshaft bolts against the timing chain as it may damage the timing chain.
  11. Torque the intake and exhaust camshaft sprocket bolts; torque as follows:
    • First Pass: 63 lb-ft. (85 Nm)
    • Second Pass: Turn an additional 30° using a torque angle gauge
  12. Install the sealing ring and tensioner assembly; torque to 55 lb-ft. (75 Nm)
  13. Install or connect the following:
    • Timing chain oil nozzle and bolt; torque to 89 lb-in. (10 Nm)
    • Camshaft cover assembly
    • Engine front cover
    • Negative battery cable; torque to 13 lb-ft. (17 Nm)

Nov 12, 2010 | 2002 Saturn L-Series

1 Answer

How to set the timing on 1998 GMC Sierra 5.7


5.0L and 5.7L Engines To Remove:
  1. Remove the crankshaft balancer.
  2. Drain the cooling system.
  3. Remove the water pump.
  4. Drain the engine oil.
  5. Remove all engine oil pan fasteners except two nuts at rear of engine.
  6. Separate the engine oil pan from the front cover.
  7. Disconnect the crankshaft position (CKP) sensor wire. gm-03-50-845.gif

  8. Remove engine front cover. gm-03-50-849.gif

  9. Pry the oil seal from the front cover.
  10. Inspect the front cover seal area and crankshaft balancer seal area for damage. gm-03-50-846.gif

  11. Rotate the crankshaft until the timing marks on the crankshaft and the camshaft sprockets are aligned.
  12. Remove the crankshaft position sensor reluctor ring. gm-03-50-847.gif

    NOTE: Free play on the slack side of the camshaft timing chain must measure less than 0.43 inch (11Mm) or timing chain and sprockets must be replaced.
  13. Remove the camshaft sprocket bolts.
  14. Remove the camshaft sprocket.
  15. Remove the camshaft timing chain. NOTE: Do not turn the crankshaft assembly after the timing chain has been removed in order to prevent damage to the piston assemblies or the valves.
    gm-03-50-848.gif

  16. Remove the crankshaft sprocket using J 5825-A.
  17. Remove the crankshaft balancer woodruff keys (if required).
To Install:
gm-03-50-850.gif

  1. Install the crankshaft balancer woodruff keys into the crankshaft.
  2. Align the crankshaft sprocket keyway with the crankshaft balancer woodruff key. WARNING
    Wear eye protection when installing crankshaft sprocket.
    gm-03-50-851.gif

  3. Use J 5590 to install crankshaft sprocket.
  4. Install the camshaft sprocket and camshaft timing chain. 9308kg61.gif

  5. Ensure that the crankshaft sprocket alignment mark is in the 12 o'clock position and the camshaft sprocket alignment mark is at the 6 o'clock position.
  6. Install the camshaft sprocket bolts and tighten the camshaft sprocket bolts;
    • Torque to: 18 ft. lbs. (25 Nm)
  7. Install the crankshaft position sensor reluctor ring until completely seated against crankshaft sprocket. NOTE: The composite type engine front cover and seal must not be reused. Always install a new engine cover with a new seal.
  8. Install new engine front cover and bolts.
    • Torque bolts to: 106 in. lbs. (12 Nm)
  9. Clean sealer from corners of oil pan gasket where it meets the engine front cover. gm-03-50-775.gif

  10. Apply a 0.196 in (5 mm) bead of adhesive, GM P/N 12346141 or equivalent, 1.0 in (25 mm) long to the engine front cover to engine block junction.
  11. Install oil pan bolts.
    • Torque bolts to: 106 in. lbs. (12 Nm)
  12. Tighten oil pan nuts.
    • Torque bolts to: 18 ft. lbs. (25 Nm)
  13. Connect the crankshaft position sensor wire.
  14. Install the water pump.
  15. Install the crankshaft balancer.
  16. Fill the engine to the proper level with oil.
  17. Fill the engine to the proper level with coolant.
  18. Test drive the vehicle to confirm the repairs.

Nov 05, 2010 | GMC K1500 Cars & Trucks

1 Answer

Installing a timing belt


Timing Belt and Sprockets REMOVAL & INSTALLATION Fig. 1: If you plan on reusing the timing belt, make sure you note the direction of the rotation before removal 91053p69.jpg Fig. 2: If the special tool is unavailable, a suitable length and width straight edge can be used to align the camshafts 91053p10.jpg Fig. 3: Camshaft alignment using the special service tool 91053g61.gif Fig. 4: Insert the crankshaft damper bolt to turn the crankshaft and . . . 91053p64.jpg Fig. 5: . . . align the camshafts and the . . . 91053g64.gif Fig. 6: . . . crankshaft before removing the old belt 91053p66.jpg Fig. 7: Loosen the timing belt tensioner pulley bolt, slide the tensioner back and . . . 91053p67.jpg Fig. 8: . . . tighten the bolt to the farthest right hand side as possible to hold the release the tensioner pulley so that the belt can be removed 91053p68.jpg Fig. 9: . . . remove the belt starting from around the camshaft pulleys 91053p01.jpg Fig. 10: Installation of the tensioner spring and retaining bolt 91053g62.gif For information on timing belt recommended replacement interval, refer to Section 1. CAUTION
The 2.0L engine is an interference motor. Extending the replacement interval could lead to the belt breaking and severe and costly engine damage. Care must be taken if rotating the crankshaft or camshafts with the belt off, if resistance is felt, do not force them to turn.
  1. Disconnect the negative battery cable.
  2. Remove the timing belt covers as outlined in this Section.
  3. Remove the valve cover.
  4. Place Camshaft Alignment Timing Tool T94P-6256-CH or equivalent, into the slots of both camshafts at the rear of the cylinder head to lock the camshafts into position. NOTE: If the special tool is unavailable, a suitable length and width straight edge can be used to align the camshafts.
  5. Loosen the camshaft timing belt tensioner pulley retaining bolt and move the tensioner pulley to relieve the tension on the timing belt.
  6. Temporarily tighten the tensioner in this position. NOTE: If the timing belt is to be reused, mark the belt for the direction of rotation before removing to prevent premature wear or failure.
  7. Remove the timing belt.
  8. If required, remove the sprockets as follows:
    1. Hold the camshaft with an appropriate camshaft sprocket holding tool.
    2. Loosen and remove the camshaft sprocket retaining bolt.
    3. Remove the sprocket from the camshaft.
    4. Repeat the procedure for the 2nd camshaft sprocket.
    5. Remove the crankshaft sprocket.
  9. Slide the crankshaft sprocket onto the crankshaft aligning the key-way.
  10. Align the camshafts using the Camshaft Alignment Timing Tool T94P-6256-CH. NOTE: If the special tool is unavailable, a suitable length and width straight edge can be used to align the camshafts.
  11. Reinstall the sprockets onto the camshafts and loosely install the camshaft retaining bolts.
  12. Tighten the camshaft sprocket retaining bolts to 47–53 ft. lbs. (64–72 Nm) .
  13. Loosely install the crankshaft pulley to verify that the engine is at TDC. Realign the marks if they have moved.
  14. Verify that the camshafts are aligned. NOTE: It is recommended to purchase a tensioner spring and retaining bolt through the dealer parts to apply the proper tension for used or new belt installations. The spring is bolted to the tensioner assembly and becomes a part of the engine. Ignore this notice if the tensioner spring is already installed.
  15. Reinstall the retaining bolt (W700001-S309) into the hole provided in the cylinder block and place the tensioner spring (6L277) between the bolt and the camshaft timing belt tensioner pulley.
  16. Tighten the retainer bolt to 71–97 inch lbs. (8–11 Nm) .
  17. Remove the crankshaft pulley and install the timing belt onto the crankshaft sprocket, then onto the camshaft sprockets working in a counterclockwise direction.
  18. Tighten the camshaft sprocket retaining bolts to 47–53 ft. lbs. (64–72 Nm) .
  19. Be sure that the span of the camshaft timing belt between the crankshaft sprocket and the exhaust camshaft sprocket is not loose.
  20. Be sure that the camshaft timing belt is securely aligned on all sprockets.
  21. Reinstall the lower timing belt cover and tighten the retaining bolts to 53–71 inch lbs. (6–8 Nm) .
  22. Apply silicone sealer to the key-way of the crankshaft pulley and install. Tighten the retaining bolt to 81–89 ft. lbs. (110–120 Nm) .
  23. Inspect the timing mark on the crankshaft pulley to verify that the engine is still at TDC.
  24. Loosen the camshaft timing belt tensioner pulley retaining bolt and allow the tensioner spring attached to the pulley to draw the tensioner pulley against the camshaft timing belt.
  25. Remove the camshaft alignment timing tool from the camshafts at the rear of the engine.
  26. Turn the crankshaft two revolutions in a clockwise direction.
  27. Tighten the camshaft timing belt tensioner pulley retaining bolt to 26–30 ft. lbs. (35–40 Nm) .
  28. Recheck that the crankshaft timing mark is at TDC for the No. 1 piston, and that both camshafts are in alignment using the camshaft alignment timing tool. NOTE: A slight adjustment of the camshafts to allow the insertion of the camshaft alignment timing tool is permissible as long as the crankshaft stays at the TDC location.
  29. An appropriate camshaft sprocket holding tool can be used to move the camshaft sprocket (s) if a slight adjustment is required.
  30. If a camshaft is not properly aligned, perform the following procedure:
    1. Loosen the retaining bolt securing the sprocket to the camshaft while holding the camshaft sprocket from turning with the sprocket holding tool.
    2. Turn the camshaft until the camshaft alignment timing tool can be installed.
    3. Verify that the crankshaft timing mark is at TDC for the No. 1 cylinder.
    4. While holding the camshaft sprocket with the camshaft sprocket holding tool, tighten the retaining bolt to 47–53 ft. lbs. (64–72 Nm) .
    5. Remove the tool and rotate the crankshaft two revolutions (clockwise) .
    6. Verify that the camshafts are aligned and that the crankshaft is at TDC for the No. 1 cylinder.
  31. Install the valve cover.
  32. Install the timing belt covers.
  33. Connect the negative battery cable. prev.gif next.gif

Aug 17, 2010 | 2000 Mercury Mystique

1 Answer

Timing belt markings mazda B2500 1998


Timing Belt, Sprockets & Front Cover Removal & Installation Timing belt To Remove:
  1. Disconnect the negative battery cable.
  2. Remove the exhaust side spark plugs, outer timing belt cover, and crankshaft pulley.
  3. Turn the crankshaft until the number one piston is at top dead center (TDC). CAUTION
    The camshaft belt tensioner tool (303-097) can be damaged when trying to relieve belt tension if you attempt to remove the belt without first loosening both the timing belt tensioner adjusting bolt and the spring pivot bolt.
  4. Loosen the timing belt spring pivot bolt, but do not remove it at this point in the procedure.
  5. Loosen the adjusting bolt slowly and release the spring tension.
  6. Turn the tensioner with the camshaft belt tensioner tool (303-097), against the spring pressure, clockwise to the farthest position.
  7. While holding it in this position, tighten the adjusting bolt to hold the tensioner away from the belt.
  8. Remove the timing belt.
To Install:
  1. Be certain that on piston number one, the crankshaft is at TDC with the crankshaft keyway pointing straight up and the circle on the crankshaft sprocket lined up with the notch on the engine front cover.
  2. Line up the timing marks.
  3. Install the timing belt over the crankshaft sprocket going counterclockwise over the oil pump sprocket and over the camshaft sprocket.
  4. Loosen the bolt allowing the tensioner pulley to press against the timing belt. NOTE: The timing belt tensioner should not be tightened or the belt tension will not be evenly distributed over the whole belt.
  5. Turn the crankshaft two revolutions clockwise. Next, slowly bring the crank to the number one position firing position with the keyway on the crank facing up. The dot on the crankshaft gear is lined up with the notch on the front cover.
  6. Check the timing mark alignment again. If necessary, repeat the procedure.
  7. Tighten the bolts. Torque the pivot bolt to 30-40 ft-lb (40-55 Nm). Torque the adjustment/locking bolt to 26-33 ft-lb (35-45 Nm).
  8. Install the crankshaft pulley and tighten the bolt. Torque to 93-121 ft-lb (125-165 Nm).
  9. Install the outer timing belt cover and tighten the bolt. Torque to 70-106 in-lb (8-12 Nm).
  10. Install the exhaust side spark plugs.
Sprockets To Remove:
  1. Remove the timing belt.
  2. Install the camshaft sprocket holding/removing tool (303-098) onto the sprocket.
  3. Remove the camshaft sprocket.
To Install:
  1. Place the key and camshaft sprocket on the shaft.
  2. Install the camshaft sprocket holding/removing tool (303-098) onto the camshaft sprocket and tighten the bolt. Torque to 52-70 ft-lb (70-95 Nm).
  3. Remove the tool then install the timing belt.
Outer Cover To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Remove the fan shroud.
  4. Loosen the bolts on the water pump pulley, but do not remove them at this point in the procedure.
  5. Remove the drive belt, the water pump pulley, and the fan and clutch assembly.
  6. Recover the refrigerant from the A/C system.
  7. Disconnect the A/C wiring connector.
  8. Remove the A/C compressor from the mounting bracket then remove the A/C mounting bracket with the power steering pump still attached.
  9. Remove the outer timing belt cover.
To Install:
  1. Install the outer timing belt cover. Torque to 70-106 in-lb (8-12 Nm).
  2. Install the A/C mounting bracket with the power steering pump still attached. Torque the M10 bolts and stud to 35 ft-lb (48 Nm) and torque the M8 bolt to 18 ft-lb (25 Nm).
  3. Install the A/C compressor to the mounting bracket. Torque to 16-20 ft-lb (21-28 Nm).
  4. Connect the A/C wiring connector.
  5. Refill the refrigerant into the A/C system.
  6. Install the fan and clutch assembly, the water pump pulley, and the drive belt.
  7. Tighten the bolts on the water pump pulley. Torque to 13-17 ft-lb (17-23 Nm).
  8. Install the fan shroud. Torque to 54-70 in-lb (6-8 Nm).
  9. Connect the negative battery cable.
  10. Start the engine. Check for leaks and repair as necessary.
Inner Cover To Remove:
  1. Loosen oil pump sprocket bolt.
  2. Remove timing belt, timing belt tensioner, oil pump sprocket, and crankshaft pulley.
  3. Remove inner timing belt cover.
To Install:
  1. Install inner timing belt cover.
  2. Install crankshaft pulley. Torque to 93-121 ft-lb (125-165 Nm).
  3. Install the oil pump sprocket.
  4. Install the timing belt tensioner. Torque the pivot bolt to 30-40 ft-lb (40-55 Nm). Torque the adjustment/locking bolt to 26-33 ft-lb (35-45 Nm).
  5. Install the timing belt.
  6. Tighten the oil pump sprocket bolt. Torque to 30-40 ft-lb (40-55 Nm).
  7. Torque the camshaft bolt to 52-70 ft-lb (70-95 Nm).

Jul 12, 2010 | 1998 Mazda Pickup

1 Answer

Ifailed to get on tdc before removing old timing belt how do I get back in time so Icanreplacebelt.


This is the complete procedure from the service manual on how to replace the timing belt start to finish, start over to assure u get it right, if u mess up the engine will be damaged

Removal for 1.6L engines : ONLY 2006 to 2009 CARS


Engine removal is not required for this procedure.

1.Remove the engine cover.

2.Remove the RH front wheel.

3.Remove the 2 bolts and RH side cover.

4.Temporarily loosen the water pump pulley bolts.

5.Remove the alternator drive belt

6.Remove the air conditioner compressor drive belt

7.Remove the power steering pump drive belt

8.Remove the 4 bolts and water pump pulley.

9.Remove the 4 bolts and
timing belt2_bing.gif upper cover

10.Turn the crankshaft pulley, and align its groove with timing mark "T" of the timing belt cover. Check that the timing mark of camshaft sprocket is aligned with the timing mark of cylinder head cover. (No.1 cylinder compression TDC position)

11.Remove the crankshaft pulley bolt and crankshaft pulley

12.Remove the crankshaft flange

13.Remove the 4 bolts and timing belt lower cover

14.Remove the timing belt tensioner and timing belt.

15.Remove the bolt and timing belt idler

16.Remove the crankshaft sprocket

17.Remove the cylinder head cover.

(1)Remove the wire harness bracket

(2)Remove the ignition coil.

(3)Remove the PCV (Positive Crankcase Ventilation) hose and the breather hose from the cylinder head cover

(4)Remove the engine cover bracket

(5)Loosen the cylinder head cover bolts and then remove the cover and gasket.

18.Remove the camshaft sprocket.

Hold the portion of the camshaft with a hexagonal wrench, and remove the bolt with a wrench and remove the camshaft sprocket.

INSTALLATION:

1.Install the camshaft sprocket and tighten the bolt to the specified torque.

(1)Temporarily install the camshaft sprocket bolt

(2)Hold the portion of the camshaft with a hexagonal wrench, and tighten the bolt with a wrench
Tightening torque :78.5 ~ 98.1N.m (8.0 ~ 10.0kgf.m, 57.9 ~ 72.3lb-ft)



2.Install the cylinder head cover.

(1)Install the cylinder head cover and bolts
Tightening torque :7.8 ~ 9.8N.m (0.8 ~ 1.0kgf.m, 5.8 ~ 7.2lb-ft)

(2)Install the engine cover bracket

(3)Install the PCV(Positive Crankcase Ventilation) hose and breather hose to the cylinder head cover.

(4)Install the ignition coil.

3.Install the crankshaft sprocket

4.Align the timing marks of the camshaft sprocket and crankshaft sprocket with the No.1 piston placed at top dead center and its compression stroke.

5.Install the idler pulley and tighten the bolt to the specified torque.

Tightening torque :42.2 ~ 53.9N.m (4.3 ~ 5.5kgf.m, 31.1 ~ 39.8lb-ft)

6.Temporarily install the timing belt tensioner

7.Install the belt so as not give slack at each center of shaft. Use the following order when installing timing belt.
Crankshaft sprocket →idler pulley →camshaft sprocket →timing belt tensioner

8.Adjust the timing belt tension.

(1)Loosen the tensioner pulley mounting bolt and apply tension to the timing belt.

(2)After checking the alignment between each sprocket and each timing belt tooth, tighten the mounting bolt and one by one.

Tightening torque :19.6 ~ 26.5N.m (2.0 ~ 2.7kgf.m, 14.5 ~ 19.5lb-ft)

(3)Then recheck the belt tension.
Verify that when the tensioner and the tension side of the timing belt are pushed in horizontally with a moderate force [approx. 49N (11lb)], the timing belt cog end is aprox. 1/2 of the tensioner mounting bolt head radius (across flats) away from the bolt head center.

4)Timing belt tension measuring procedure
(by a sonic tension guage)
Rotate crankshaft in clockwise direction to set 1st piston on top dead center (TDC) and rotate crankshaft in counterclockwise to 90° then measure the belt tension in the middle of tension side span (in arrow direction of above illustration) by free vibration method.


9.Turn the crankshaft two turns in the operating direction (clockwise) and realign crankshaft sprocket and camshaft sprocket timing mark.


10.Install the timing belt lower cover with 5bolts

Tightening torque :7.8 ~ 9.8N.m (0.8 ~ 1.0kgf.m, 5.8 ~ 7.2lb-ft)

11.Install the flange and crankshaft pulley, and then tighten crankshaft pulley bolt. Make sure that crankshaft sprocket pin fits the small hole in the pulley.

Tightening torque :137.3 ~ 147.1N.m (14.0 ~ 15.0kgf.m, 101.3 ~ 108.5lb-ft)

12.Install the timing belt upper cover with 4 bolts.

Tightening torque :7.8 ~ 9.8N.m (0.8 ~ 1.0kgf.m, 5.8 ~ 7.2lb-ft)

13.Install the water pump pulley and 4 bolts.

14.Install the power steering pump drive belt

15.Install the air conditioner compressor drive belt

16.Install the alternator drive belt

17.Install the RH side cover with 2 bolts

18.Install the RH front wheel.


Tightening torque :88.3 ~ 98.1N.m (9.0 ~ 10.0kgf.m, 65.1 ~ 72.3lb-ft)

19.Install the engine cover with bolts.


Tightening torque :3.9 ~ 5.9N.m (0.4 ~ 0.6kgf.m, 2.9 ~ 4.3lb-ft)

May 20, 2010 | 2006 Kia Sorento

2 Answers

I need 2004 Hyundai XG350L Service/repair Manual


3.5L Engine

Remove or disconnect the following:
  1. Negative battery cable
  • Engine coolant
  • Water pump pulley bolts
  • Alternator bolt, loosen only
  • Water pump pulley and drive belts
  • Crankshaft pulley
  • Timing belt cover(s)
  1. Turn the crankshaft until the timing marks on the camshaft sprocket and cylinder head are aligned.
  2. Loosen the timing belt tensioner bolt and turn the tensioner counterclockwise as far as it will go. Tighten the adjusting bolt.
  3. Mark the timing belt with an arrow showing direction of rotation.
  4. Remove the timing belt.
  5. If defective, remove the timing belt tensioner.

9767b45.gif
Timing belt sprocket alignment mark positioning for belt removal and installation—3.5L engine

To install:
  1. If necessary, install the timing belt tensioner.
  2. Attach the top of the tensioner spring on the engine coolant pump pin. Ensure the hook on the pin is facing down and the hook on the tensioner is facing away from the engine
  3. Rotate the timing belt tensioner to the extreme counterclockwise position. Temporarily lock the tensioner in place.
  4. Align the timing marks of the camshaft and crankshaft sprockets.
  5. Install the timing belt on the crankshaft sprocket, then onto the rear camshaft sprocket.
  6. Route the belt to the coolant pump pulley, the front camshaft sprocket and the timing belt tensioner.
  7. Apply force counterclockwise to the rear camshaft sprocket with tension on the tight side of the belt and check that timing marks are aligned.
  8. Loosen the tensioner bolt 1–2 turns and tighten the timing belt to a tension of 57–84 lbs. (260–380 N).
  9. Turn the crankshaft two turns clockwise.
  10. Readjust the sprocket timing marks and tighten the tensioner bolts.
  11. Install the timing belt covers.
  12. Install the crankshaft pulley and tighten to 108–116 ft. lbs. (150–160 Nm).
  13. Install or connect the following:
    • Timing belt cover(s)
    • Crankshaft pulley
    • A/C compressor belt
    • Water pump pulley
    • V belt
    • Negative battery cable
    • Engine with coolant

Feb 10, 2010 | 2004 Hyundai XG350

2 Answers

Replacing timing belt on daewoo nubira 2000 model


Instructions Difficulty: Moderate Things You’ll Need:
  • Set of ¼-inch drive sockets ¼-inch drive ratchet Set of ½-inch drive sockets ½-inch drive ratchet Set of 3/8-inch drive sockets 3/8-inch drive ratchet Set of metric wrenches Floor jack Jack stands
Step1 Raise and support the vehicle on jack stands. Remove the intake air temperature wiring, the breather hose and intake air hose. Take off the air cleaner assembly. Step2 Remove the right wheel. Remove the accessory belts. Remove the crankshaft bolt and the crankshaft pulley. Remove the power steering bolts and the timing belt covers. Temporarily install the crankshaft bolt and turn the engine clockwise until the mark on the crankshaft pulley, which is a triangle stamped into the crank sprocket, is aligned with the corresponding triangular mark on the block. Step3 Make sure that the timing marks are aligned on the camshaft sprockets. These are a line on each sprocket that runs through a tooth on each sprocket. These lines should line up in the middle between each sprocket and point toward each other. If they do not line up, turn the crankshaft one more time and they will line up. It takes two turns of the crank to one complete revolution of the cam. Step4 Loosen the water pump bolts; using the 3/8-inch ratchet, turn the water pump clockwise away from the belt and loosely tighten the bolts to keep it there. Remove the timing beltmag-glass_10x10.gif. Make sure the timing marks are aligned and install the new belt starting on the right side from the crank sprocket and working counterclockwise. Keep all the belt tension on the right side away from the tensioner. Step5 Loosen the bolts in the water pump and rotate the water pump counterclockwise to apply tension to the belt. Watch the tensioner, which is above the water pump, and apply tension with the water pump until the pointer on the tensioner lines up with the notch above it. Lightly tighten the water-pump bolts. Step6 Turn the engine two more times and align the timing marks perfectly. Loosen the water-pump bolts and, using the ratchet, apply tension to the belt until the tensioner pointers are aligned. Tighten the water-pump bolts. Step7 Install the timing-belt covers and the bolts in the power-steering pump and tighten. Remove the crankshaft bolt and install the crank pulley and the bolt, then torque the crankshaft pulley bolt to 70 foot pounds of torque. Install all components in reverse order of removal.

Mar 02, 2009 | 2000 Daewoo Nubira

1 Answer

2004 Durango 5.7 timing gear alignment


  1. If tensioner assembly is being replaced, install tensioner and mounting bolts. Torque bolts to 28 Nm (250 in. lbs.) .
  2. Retract tensioner if required. CAUTION: The camshaft pin and the slot in the cam sprocket must be clocked at 12:00. The crankshaft keyway must be clocked at 2:00. The crankshaft sprocket must be installed so that the dots and or paint marking is at 6:00.
  3. Place both camshaft sprocket and crankshaft sprocket on the bench with timing marks on exact imaginary center line through both camshaft and crankshaft bores.
CAUTION: The timing chain must be installed with the single plated link aligned with the dot and or paint marking on the camshaft sprocket. The crankshaft sprocket is aligned with the dot and or paint marking on the sprocket between two plated timing chain links.
b04dbf8.jpg

Feb 13, 2009 | 2004 Dodge Durango

Not finding what you are looking for?
2005 Chevrolet Aveo Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...