Question about 1998 Chrysler Town & Country

1 Answer

Washer bottle motor 1998 chrysler grand voyager 3.3 LX

I have a 1998 chrysler grand voyager 3.3 LX and i need to know if the washer bottle motor is connected to the water bottle or not

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 578 Answers

Should be located at the bottom attch to bottle follow the plug wire for washer motor and u will see and u will see

Posted on Jul 01, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Can you tell me were the washer fluid motor is on a 1998 1500 silverado


The washer motor is located on the washer bottle, this is the bottle you put the washer fluid into, it snaps into the side of it and theres a hose and a conntection to it, some times you dont need to remove the bottle depending on its location you can just remove the pump motor off the side but if bottle needs removing then its not a big job, hope this helps also heres a picture of the washerpump to help you find it,johnjohn2_42.jpg

Dec 19, 2010 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Where physically is the blower motor resistor located for 2000 Chrysler Grand Voyager? Checked underneath glove box but underneath is encased in plastic. Need to remove plastics?


open hood, at right side of vehicle underneath wiper module, at firewall, no need to remove wiper module.let me know if this help

Nov 19, 2009 | 2000 Chrysler Grand Voyager

1 Answer

The fan blower only works on high. The other


its the resistor, and its located with the blower motor. you will need a new motor assy. .......in Chryslers infinite wisdom, its all one unit.

Oct 08, 2009 | 1998 Plymouth Voyager

1 Answer

Washer bottle 1998 chrysler grand voyager 3.3 LX


If you are talking about the window washer bottle and the cooling system bottle the answer is no. The washer bottle goes to the winshield washer ports and the coolent bottle goes to the radiator

Jun 29, 2009 | 1998 Plymouth Grand Voyager

2 Answers

Windsield washer not working 1996 Plymouth Grand voyager


If you can hear a clicking noise it want be the fuse change the washer motor

Jun 10, 2009 | 1996 Plymouth Grand Voyager

2 Answers

Washer bottle motor


First, check actual battery voltage (should be 12v or better with engine off. Then check that all connections are clean and properly secured at both ends of the battery cables. If battery is a bit old, have it load tested. Once you get past that, put a volt meter across the battery terminals and crank engine (or try). If voltage drops below 9.5v change the starter. Once you get started, finish by checking alt output...should be between 12.9 and no higher than 14 at idle, should hold around 13v or better with no drop off with all lights, heater radio etc on. Maske sure alt drive belt is in good condition.

May 10, 2009 | 1998 Plymouth Grand Voyager

1 Answer

Replacing radiator fan motor on 2000 chrysler grand voyager


Disconnect the wires leading to both of the fans. Remove the cross-member that goes over the radiator. Remove the four bolts securing the fan assembly and lift it out.

Apr 13, 2009 | 2000 Chrysler Grand Voyager

2 Answers

Front windshield washer motor does not work.


It should be located at the bottom of the tank held in by a rubber grommet. I think the best way to get to it is to remove the tank, sorry if this doesn't help much. Since I work at a Chrysler dealer I will try to get a better way for you tomorrow at work, and a price of the new pump in case that is the problem.

Jan 08, 2009 | 2002 Chrysler Voyager

Not finding what you are looking for?
1998 Chrysler Town & Country Logo

Related Topics:

235 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

81423 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...