Question about 2007 Dodge Ram 3500 Quad Cab Laramie

1 Answer

How do you remove the flywheel when replacing the clutch

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 108 Answers

Unless there is something wrong with the flywheel there is no need to remove it.All that is needed to replace the clutch is to remove the pressure plate and the clutch will fall off. But if the flywheel must be removed just remove the six bolts holding it to the crankshaft after removing the clutch.


bigc

Posted on Jul 01, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Flywheel replacing


you will need a replica flywheel and new bolts plus torque range and manfacturers specs.

Nov 07, 2016 | Cars & Trucks

1 Answer

I need to replace a flywheel on a 87 ford f150 4x4 manual trans.Need to know what I need to take off to get to flywheel


everything attached to trans and pull trans out, remove clutch assy, replace flywheel, if clutch is worn, replace it as well, do not use rebuilt clutch parts they will not last,

Aug 31, 2013 | Cars & Trucks

1 Answer

I have removed the gearbox from my 2000 MB 100 Van. I found the clutch plate has disintergrated. I noticed the Flywheel clutch pressure face looks like it will come off. Is there more to this clutch system...


flywheel bolted to engine, clutch disk and pressure plate, also has a throw out bearing that should be replaced at the same time.
you don't need to replace the flywheel unless it is cracked though you should have it turned down at a machine shop.

Oct 11, 2012 | Mercedes-Benz Cars & Trucks

1 Answer

Need a copy of the manual pages, showing how to replace the clutch


Removal & Installation To Remove:
  1. Remove the transmission.
  2. Install a flywheel locking tool.
  3. Remove the pressure plate mounting bolts from the flywheel.
  4. Remove the pressure plate and clutch disc.
To Install:
  1. Insert a clutch disc alignment tool through the disc splines and into the flywheel pilot bearing. Pressure plate balance mark location subaru-07-00-6722.gif

  2. Install the pressure plate on the flywheel with a gap of 120° or more between the "0" balance marks on the flywheel and pressure plate. Hand tighten the pressure plate mounting bolts.
  3. Tighten the pressure plate mounting bolts using a crisscross pattern 12 ft-lb (16 Nm).
  4. Remove the clutch disc alignment tool.
  5. Install the transmission.
prev.gif next.gif

Dec 28, 2010 | 1998 Subaru Legacy

2 Answers

How get to flywheel bolts


In the Toyota Pick-ups/Land Cruiser/4Runner 1989-1996 (free register) can find several graphics about this.

Driven Disc and Pressure Plate - REMOVAL & INSTALLATION

(see Figures 1 through 27).

cc66ac3.jpg


CAUTION The clutch driven disc may contain asbestos, which has been determined to be a cancer causing agent. Avoid inhaling any dust from any clutch surface! When cleaning clutch surfaces, use a commercially available brake cleaning fluid. Never clean clutch surfaces with compressed air.
  1. Remove the transmission.
  1. Matchmark the clutch cover (pressure plate) and flywheel, indicating their relationship.
  1. Loosen the clutch cover-to-flywheel retaining bolts one turn at a time in a crisscross pattern. The pressure on the clutch disc must be released GRADUALLY.
  1. Remove the clutch cover-to-flywheel bolts. Remove the clutch cover and the clutch disc.
  1. If the clutch throwout bearing is to be replaced, do so at this time as follows:
  1. Remove the bearing retaining clip(s) and remove the bearing and hub.
  2. Remove the release fork and the boot.
  3. The bearing is press fit to the hub. Turn the bearing by hand while placing it under some pressure; check for freedom of motion and lack of grinding or resistance. The bearing is permanently lubricated and cannot be disassembled or greased.
  4. Clean all parts; lightly grease the input shaft splines and all of the contact points.
  5. Install the bearing/hub assembly, fork, boot, and retaining clip(s) in their original locations.
  1. Inspect the flywheel surface for cracks, heat scoring (blue marks), and warpage. If oil is present on the flywheel surface, this indicates that either the engine rear oil seal or the transmission front oil seal is leaking. If necessary, replace the seal(s). If in doubt concerning the condition of the flywheel, consult an automotive machine shop.
  1. Before installing any new parts, make sure that they are clean. During installation, do not get grease or oil on any of the components, as this will shorten clutch life considerably. Grease or fingerprints may be cleaned with an evaporative cleaner such as the type used on brake linings.

To install:
  1. Position the clutch disc against the flywheel. The long side of the splined section faces the flywheel.
  2. Install the clutch cover over the disc and install the bolts loosely. Align the matchmarks made. If a new or rebuilt clutch cover assembly is installed, use the matchmark on the old cover assembly as a reference.

Whenever the clutch disc is replaced, replacement of the pressure plate (clutch cover) and release bearing is highly recommended.
  1. Align the clutch disc with the flywheel using a clutch aligning tool. These handy tools are available in many auto parts stores at a reasonable price. Do NOT attempt to align the clutch disc by eye; use an alignment tool.
  1. With the clutch aligning tool installed, tighten the clutch cover bolts gradually in a star pattern, as is done with lug nuts. Final tighten the bolts to 14 ft. lbs. (19 Nm).
  2. Apply molybdenum disulfide grease or multi-purpose grease to the release fork contact points, the pivot and the clutch disc splines. Install the boot, fork, and bearing on the transmission input shaft.
  3. Install the transmission.
Hope helped.

Mar 15, 2010 | Toyota Pickup Cars & Trucks

1 Answer

How to fit a new clutch into a ford escort 1300cc 1994


1991-96 Models
See Figures 1, 2 and 3
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Remove the transaxle assembly.
  4. If the clutch assembly is to be reused, matchmark the pressure plate and the flywheel so they can be assembled in the same position.
  5. Install flywheel holding tool T84P-6375-A or equivalent, in a transaxle mounting hole on the engine and engage the tooth of the holding tool into the flywheel ring gear.



0900c1528008df86.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Install a flywheel holding tool in a transaxle mounting hole on the engine, and engage the tooth of the tool into the flywheel ring gear
  1. Loosen the pressure plate-to-flywheel retaining bolts one turn at a time, in a crisscross pattern, until the spring tension is relieved, to prevent pressure plate cover distortion.
  2. Support the pressure plate and unfasten the retaining bolts. Remove the pressure plate and clutch disc from the flywheel.

If the flywheel shows any signs of overheating (blue discoloration) or if it is badly grooved or scored, it should be refaced or replaced.
  1. Inspect the flywheel, clutch disc, pressure plate, release bearing, pilot bearing and the clutch fork for wear. Replace parts as needed.

To install:
  1. If removed, install a new pilot bearing using a suitable installation tool.
  2. If removed, install the flywheel. Make sure the flywheel and crankshaft flange mating surfaces are clean. Tighten the flywheel retaining bolts to 71-76 ft. lbs. (96-103 Nm) on the 1.8L engine or 54-67 ft. lbs. (73-91 Nm) on the 1.9L engine.
  3. Clean the pressure plate and flywheel surfaces thoroughly. Position the clutch disc and pressure plate into the installed position and support them with a dummy shaft or clutch aligning tool. If the clutch assembly is being reused, align the matchmarks that were made during the removal procedure.
  4. Install the pressure plate-to-flywheel retaining bolts. Tighten the bolts in the correct sequence to 13-20 ft. lbs. (18-26 Nm). Remove the alignment tool.



0900c1528008df87.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Position the clutch disc and pressure plate into the installed position and support them with a clutch aligning tool


0900c1528008df88.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: Tighten the pressure plate-to-flywheel retaining bolts to specification in the sequence illustrated
  1. If the release bearing was removed, lubricate the release fork where it contacts the bearing and install the bearing in the fork.
  2. Install the transaxle assembly.
  3. Lower the vehicle.
  4. Bleed the hydraulic clutch system, if needed.
  5. Connect the negative battery cable.
  6. Road test the vehicle and check the clutch for proper operation.

Sep 30, 2009 | 1994 Ford Escort

1 Answer

Info on do it tyour self clutch removal on 2001 mustang 3.8


REMOVAL:
  1. Lift clutch pedal to uppermost position to disengage clutch and brake pedal pivot shaft.
  2. Push clutch and brake pedal pivot shaft forward and unhook clutch release lever cable from clutch and brake pedal pivot shaft and allow it to slowly swing rearward.
  3. Raise and support vehicle.
  4. Remove clutch release lever dust shield.
  5. Disconnect clutch release lever cable from clutch release shaft.
  6. Remove retaining clip, then clutch release lever cable from flywheel housing.
  7. Remove starter motor from flywheel housing, then engine rear plate to front lower flywheel housing bolts.
  8. Remove transmission.
  9. Remove flywheel housing back just far enough to clear clutch pressure plate, then remove housing.
  10. Remove clutch release shaft from flywheel housing by pulling it through window in flywheel housing until retainer spring disengages from pivot.
  11. Remove clutch release hub and bearing from clutch release shaft.
  12. Loosen six clutch pressure plate bolts evenly to release spring tension gradually and avoid distorting clutch pressure plate. If same clutch pressure plate is to be installed, mark plate and flywheel so pressure plate can be installed in its original position.
  13. Remove clutch pressure plate and clutch disc from flywheel.
INSTALLATION:
  1. Position clutch disc and pressure plate assembly on flywheel, noting following:
    1. Three flywheel housing to block dowels on flywheel must be properly aligned with clutch pressure plate.
    2. Bent, damaged or missing flywheel housing to block dowels must be replaced.
    3. tart clutch pressure plate bolts but do not tighten.
    4. Avoid touching clutch disc face, dropping parts or contaminating parts with oil or grease.
    5. Align clutch disc using suitable alignment tool inserted in pilot bearing.
    6. To avoid clutch pressure plate distortion, alternately tighten bolts a few turns at a time, until they are all tight, then tighten to specifications.

  2. Install transmission to flywheel housing.
  3. Install engine rear plate to flywheel front lower housing bolts, then connect clutch release cable to flywheel housing and connect retaining clip.
  4. Connect clutch release lever cable to clutch release shaft, then install clutch release lever dust shield.
  5. Install starter motor.
  6. Lower vehicle, then install clutch release lever cable as follows:
    1. Lift clutch pedal to disengage clutch and brake pedal pivot shaft.
    2. Push clutch and brake pedal pivot shaft forward and hook end of clutch release lever cable over rear of clutch and brake pedal pivot shaft.

  7. Cycle clutch pedal several times to adjust clutch release lever cable

Aug 08, 2009 | 2001 Ford Mustang

1 Answer

How do you remove the flywheel when replacing the clutch


Take trans out, clutch out, and remove the flywheel bolts.

May 30, 2009 | 2007 Dodge Ram 3500 Quad Cab Laramie

1 Answer

Wanting to replace the clutch because it is slipping.


Hope this helps. Best of luck to you!
Greg

Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Remove the transaxle.
  4. Gradually loosen the clutch pressure plate bolts, in a crisscross pattern. Support the pressure plate and remove the bolts. Remove the pressure plate and clutch disc.
  5. Inspect the pilot bearing. If it is worn or damaged and does not turn easily by hand, remove it using a puller/slide hammer.
  6. Check the flywheel surface for scoring, cracks or burning and machine or replace, as necessary.
  7. Install a flywheel holder to keep the flywheel from turning. Loosen the flywheel bolts evenly and gradually in a crisscross pattern. Remove the flywheel.
  8. Inspect the clutch release bearing for wear. Replace it if it sticks or does not turn easily.
  9. Inspect the release fork for wear or damage and replace as necessary.
To install: 7923kg32.gif Structural view of the hydraulic clutch system
7923kg33.gif Exploded view of the clutch assembly
Click to Enlarge
7923kg34.gif Flywheel tightening sequence
7923kg35.gif Pressure plate tightening sequence

  1. Lubricate the release fork fingers and pivot with molybdenum grease and install in the release fork boot.
  2. Install the clutch release bearing on the release fork.
  3. Install a new pilot bearing in the flywheel, if removed.
  4. Be sure the flywheel mounting surface and the crankshaft or eccentric shaft mounting surfaces are clean. Remove any old sealant from the flywheel bolt hole threads and the flywheel bolts.
  5. Install the flywheel.
  6. Apply sealant to the flywheel bolt threads and install them hand-tight. Install the flywheel holding tool. Tighten the bolts, in a crisscross pattern, to 71–76 ft. lbs. (96–103 Nm).
  7. Apply a small amount of molybdenum grease to the clutch disc splines and install the clutch disc on the flywheel, spring side toward the transaxle. Install a suitable alignment tool in the pilot bearing to position the clutch disc.
  8. Install the clutch pressure plate, aligning the dowel holes with the flywheel dowels.
  9. Install the pressure plate bolts and gradually tighten, in a crisscross pattern to 20 ft. lbs. (26 Nm). Remove the alignment tool.
  10. Install the transaxle.

May 20, 2009 | 2004 Kia Rio

1 Answer

How do you replace clutch in 1997 toyota corolla? Do you need to replace entire clutch assy or just the clutch disc?


I see. sounds like you need a new clutch. OK, here is a step by step guide to follow. it will help with the removal and installation of your new clutch.

Remove the Old Clutch Step1 Verify that your vehicle's clutch is the source of your problems and not the pedal-arm bushings, activating cables or the slave-master cylinder. Step2 Unhook the positive battery cable, the clutch cable or hydraulic slave cylinder to get the transaxle ready for easy removal. Eliminate anything that may hinder your efforts, including exhaust pipes and the speedometer. Step3 Secure your car in a safe position before jacking up the front end. Step4 Stabilize the engine with a jack below the oil pan. Remove the transaxle by undoing at least one engine mount. Step5 Separate the engine from the transaxle by removing the bolts that surround the flywheel bell housing. Step6 Push the transaxle away from the engine until the input shift clears the pressure plate. Step7 Disengage the bolts surrounding the pressure plate and take it and the clutch disc out. Check to see if the flywheel's friction surface is scored, checked or has hot spots. Remove, machine and reinstall the flywheel, if needed. Step8 Examine the pilot bearing (bushing) located at the flywheel's center to be sure the needle bearings are lubricated and that there's no galling. Also look for any oil leaking around the rear main engine seal. Replace the clutch Step1 Follow the instructions for replacing your car's clutch carefully to avoid having to remove the transaxle. Step2 Check that the transaxle's input shaft isn't leaking; replace if needed. Step3 Take out the flywheel and the old seal and install a new seal. Install a New Clutch Step1 Clean the crankshaft flange before putting in the flywheel. With the flywheel on top of the flange, secure the bolts in a star formation to the specified torque for your vehicle. Step2 Install the clutch disc and pressure plate. Prior to putting in the transaxle, attach the new release bearing to the release fork. The fork should move freely. Step3 Hoist the transaxle into position and move it forward until the input shaft glides into the clutch disc's spindled hole. Do not apply force. Step4 Reinstall any bolts or mounts that were removed to replace your car's clutch. Grab the transaxle, release the jack and lower your vehicle. Step5 Consider replacing your car's clutch cable. If you don't replace the cable at least adjust it for the right amount of free-play. Step6 Confirm that your clutch's self-adjusting action is performing correctly by depressing the slave cylinder's piston into its bore. Step7 Drive your car to be sure your clutch is working properly.


PLease rate and god bless:)

Apr 03, 2009 | 1997 Toyota Corolla

Not finding what you are looking for?
2007 Dodge Ram 3500 Quad Cab Laramie Logo

Related Topics:

242 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...