Question about 1994 Dodge Intrepid

5 Answers

My car isnt getting spark i replaced the coil pack what else could be the problem it's not a fuel problem cranks just fine all fuses are fine

Posted by on

  • yadayada
    yadayada May 11, 2010

    the last thing i would replace would be the coil pack, whay did u do this? did you have a trouble code?

×

5 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

If you have a volt meter unplug the crank sensor and test the power to the orange wire with the ignition on the power should be 8 volts if you have that than try pluging the crank sensor back in and back probe the light and dark blue wire on the side of the plug. when you are turning the motor over it should go back and forth from .3 volt to 5 volt if it dont fluxuate you need a crank sensor

Posted on Aug 24, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 166 Answers

Hi thies car are know for crank sensors

Posted on Jul 10, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 109 Answers

CHECK THE CAM SENSOR AND CRANK SENSOR!!

Posted on Jul 01, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 73 Answers

The crank sensor sends the signal to the coil, i would check it next

Posted on Jul 01, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Cam sensor, crank sensor, or ignition module

Posted on Jul 13, 2009

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 120 Answers

SOURCE: The car cranks but no start, fuel is fine, no

coil needs replaced.

Posted on Aug 24, 2009

Testimonial: "Thanks for your help, I should have mentioned I changed the coil, I thought the same thing "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 neon will not start


Check the ASD relay in under hood fuse/ relay box. ASD stands for automatic shut down relay. Powers up pcm ,fuel injectors and ignition system an O2sensor heaters .crank over the car an check for power at O2sensor heater fuse in the underhood fuse box ,no power means bad relay !

Jan 18, 2015 | Cars & Trucks

2 Answers

Why isnt my1993 ford ranger no spark no fuel


did you back into anything or did anything hit truck before this happend if so check your emergancy shut off switch. check it anyway and reset it.

Aug 22, 2014 | 1993 Ford Ranger SuperCab

1 Answer

My 96 volvo 850 gtl2.4L ENGINE CRANK OVER BUT WONT START I REPLACED THE INGNITION COIL \ POWER STAGE WITH NO RESULTS.PLEASE HELP


Reasons for engine turning over and not firing are simple. Spark or fuel. If you've changed the coil packs then chances are it's a fuel issue. Get in cab and turn ignition to second position whilst listening to back seat. You should hear the faint noise of the fuel pump working. If you can't, I suggest you firstly check your manual to find the fuse/relay for the fuel pump and check that. If they are fine, you need to replace fuel pump.

If you can hear it working and it still won't start, remove the fuel line going to injector rail and point into a jar whilst someone turns engine over. You should have fuel coming out. If this is fine, go back to ignition, remove a spark plug and turn engine over checking for a spark.

My bet is your fuel pump has packed-up. Good luck diagnosing.

Jan 22, 2014 | Volvo Cars & Trucks

1 Answer

No fire to plugs on 1991 ford aerostar 4.o replaced crank sensor,coil pack and switch what else is there


If the engine cranks but has no spark, you need to know if the coil is getting voltage and a ground signal. The coil gets power from the ASD relay and a fuse.
Have you checked the compuer for trouble codes ?

Jul 08, 2012 | 1991 Ford Aerostar Extended

1 Answer

Have a 1999 ford explorer sport 4x4, cranks want start. have replaced fuel pump, crank senser and cam senser, checked fuzes, replaced computer. doesnt seem to be firing


When you turn the key on you should beable to hear the fuel pump come on. Other than that you have a fuel pressure test port, looks just like a tire valve stem get a little probe press the valve after cranking fuel should come out strongly and not dribble out. If is doesnt seem to be firing your going to have check the coil pack for spark from the coil pack take one plug wire out and put it in a position that as you crank the vehicle you will be able to see spark jump or even hear give it a 1/4 air gap from its connection. If you dont have spark and your timing chain isnt broken you need to check for power the choice of tool is a test light.or volt meter. If you dont have either test tool we will go by sound when you turn the key on the engine fuse box has relays do you hear them click. That click noise will be fuel pump relay and PCM relay for power inpect those relays for corrode connections you mainly have a power problem and inspect for proper ground a missing ground can also cause the ECM to not fire the coils2_26_2012_7_32_43_am.gif

Feb 26, 2012 | 1999 Ford Explorer

1 Answer

1995 Geo Prism wont start


check all fuses real good with test ligh..i mean alll fuses.... next sounds like ignition switch might be bad... not supplying voltage to coil in crank position..but when let off cranking it returns back to run position it momentarily causes spark

Sep 06, 2009 | 1996 Geo Prizm

Not finding what you are looking for?
1994 Dodge Intrepid Logo

1,178 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...