Question about 2000 Chevrolet Metro

1 Answer

What is the cost of CV joint for a ch Chevy Geo metro 2000, 4 cylinder? The car makes a lot of noise when I take a curve. Like iron cracking.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 21 Answers

If you are in the states they run around $75 to $100 at shucks/checker/kragen/oreilly auto. you can check exact prices at shop.oreillyauto.com. the site will also show availablitiy for your area.

I recomend changing both sides at the same time. unless there was damage to the axle shaft from say... offroading or an accident (yes you can offroad a metro... used to take mine on 4wheeler trails all the time), there is a chance the other side will go out before too long as well. if you replace one side and not the other you may also notice a pull to the side that was not changed, due to one being worn drastically more than the other. hope this helps
.

Posted on Aug 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Symptoms of a bad cv joint


x10 , lug bolts,
or even cracked rims
or even bad wheel bearings
or even brake rotor bad. warped.
doing a hands on full inspection (man handling parts)
is the only way, guessing on the net is zero solution.
I can list maybe 25 ways to make noise. on car.
why do that.?

Mar 24, 2014 | 1996 Geo Metro

1 Answer

Noise in front end when driving


if the cv joint have been replaced and they are still fine bearing in mind the could be falty units, then sheck wheel bearings check for play

Dec 30, 2013 | 1992 Geo Metro

1 Answer

99 geo metro automatic transmission grinds when put into gear,it happened with no warning of a malfuction,what happened?


CV Joints can break internally and cause the sound similar to trans problems.

You will either need a new axle/CV Joint, or to probably replace/rebuild the Transaxle completely.

You may be able to tell more from underneath with someone turning the wheel as you watch the CV Joint housing to make sure it's moving at the same time on both ends. If one end of the shaft moves, the other should move equally, not just the axle shaft, the ends that go into the trans and through the front wheels!


Good luck!

Mar 21, 2012 | Geo Metro Cars & Trucks

1 Answer

Chevy trailblzr has about 150000 miles and just started to make a loud sound ch ch ch ch ch ch ch . Loud enough that passersby look. Went to mechanic who said it is just rus and that sound is metal and...


Metal and rust reacting??? I wouldn't let that guy work on a skate board!
If it is rust on the brake rotors causing the problem, then the rotors will probably need to be machined or replaced if it is making that much noise. They shouldn't be doing that regardless of how much rain we have - that would require a LOT of rust and it would need to be repaired! Also, are you sure it is not coming from something like a bad driveshaft U-joint or axle CV joint? If it is, it could leave you STRANDED when it comes apart. I would recommend taking it somewhere else and getting the noise properly diagnosed.

Sep 23, 2011 | 2003 Chevrolet TrailBlazer

1 Answer

1996 geo metro, passenger side half shaft (CV joint) Shaft and ball joint shaft stuck in spindle unit. Tried lube and a wheele puller, any good ideas??


i use a 3 arm puller to force the shaft out of the hub spline (do not hammer on the cv shaft at all, you will destroy it), and either a pickle fork or a specialy designed ball joint puller to seperate the balljoint from the knuckle. if you dont have a special puller and need to save the balljoint. try using a 6 or 8 foot steel bar to pry down on the lower control arm while another person strikes the knuckle at the balljoint location. note pin retainer type balljoints have a small slot which can be spread open alittle with a cold cut chisel or larg screw driver once the cv shaft is out of the way

May 28, 2010 | 1996 Geo Metro

1 Answer

How do u know when your cv joint went out?


CV joints make a Clicking noise while turning Corners, Yours Sounds more like a Strut Or Ball Joint/ Suspention Problem

May 31, 2009 | 1990 Geo Metro

1 Answer

97 chevy cav popping noise


The pop sound is coming from the CV joint most likely,but if the splines of the drive hub or drive shaft are worn and slipping they will pop too.At a good shop you'll be looking at probably around $400-$500 it really depends on the shop,give or take with parts and labor,and they will inspect the drive hub also.Just because the joint is making a popping noise doesn't mean its going to fail anytime in the near future,the car will vibrate when the joint is going to fail,I'm telling you this so if your a bit short on funds and wondering if it needs to be done immeadiatley,this CV could last another 6 months or a year or even longer.If you do decide to replace it,get estimates from a few shops because the labor price can vary quite a bit,especially with the econmy the way it is,if you live in a metro area there are ussually shops that will specialize in driveshaft/CV replacement.I hop this helps

May 15, 2009 | 1997 Chevrolet Cavalier

1 Answer

Grinding


cv axles dont usually grind. sounds like brakes or backing plate

Dec 13, 2008 | 2000 Chevrolet Metro

1 Answer

'97 Geo Metro DriveShaft


hi depends who does the job are you useing a garage or are you getting a mate to do it or are you doing it yourself the parts new if its the outer cv joint it around £20-£30 the complete shaft £80-£100 new could use a breakers it would be in the region of £30-£40 for the complete shaft and an hour to change check around some people are greedy some just ask a fair price best of luck paul

Oct 15, 2008 | 1994 Geo Metro

Not finding what you are looking for?
2000 Chevrolet Metro Logo

313 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...