Question about 2003 Mitsubishi Eclipse Spyder

1 Answer

Can you just replace a brake light bulb? or do you have to replace the entire assembly?

Posted by on

  • kcflannery Jul 01, 2009

    I'm not sure it's a 2003 Mitsu spyder, pass rear assembly.

  • yadayada
    yadayada May 11, 2010

    is this a LED brake light fixture?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 21 Answers

Just the bulb. it should be acessible from the inside of the car under the carpet or trim(the back side of the light assembly)

Posted on Jul 01, 2009

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: replacing a brake light bulb for a 2006 chevrolet equionx

This is almost correct...instead f straight back pull straight out from the side, right light, pull to the right, left bulb, pull to the left.
Worked great.

Posted on Dec 29, 2008

MrScary66613
  • 1990 Answers

SOURCE: I want to remove and

The Mounts for these are Under the Hood and Look like Wing Nuts But Plastic. Should be around the Area that the Light Harness Plugs into the Back of the Housing

Posted on Jan 01, 2009

  • 43 Answers

SOURCE: Right brake light is out. How do I get to it to replace the bulb

in the trunk your capet is held in by plastic nuts.unsrew three or four nuts to pull capet back.then there is three or four nuts on long studs.remove the nuts only.gently pull lamp out to access the bulbs.

Posted on Mar 30, 2009

  • 1986 Answers

SOURCE: Rear Light Bulb Replacement

unfortunately you will have to remove the assembly to get to the bulbs

Posted on Oct 01, 2009

  • 1 Answer

SOURCE: 2002 Chevy Tahoe: Replacing Bulbs in Rear High Mount Stop Light?

Yes you can do this your self. When you open the back hatch their should be a way to take out the whole back light system, which then you can replace each individual light.

Posted on Oct 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing brake light


Hi Edward-
The top brake light lens is held on with two size T25 Torx screws. You need a suitable size torx screw driver to remove (and again later replace the assembly) the two screws. Once the screws are removed (do not lose these), you can remove the entire lens assembly. You'll see the wires leading to the plastic bulb socket. The bulb socket twists off the assembly like a bayonet. Once the bulb socket is off, you'll be able to remove the bulb simply by pulling it straight out. Replace the bad bulb by inserting the new bulb and then reassemble your third brake light in the reverse order you removed it. Enjoy!

Apr 01, 2014 | 2007 Dodge Caravan SXT Minivan New Cars

1 Answer

How do I change the Brake Light Bulbs for a 2000 Oldsmobile Alero?


Open the trunk. There will be about 3 nuts holding the entire light assembly in place. Remove these and gently pull the assembly away from the body of the car.
The bulbs sockets twist in one direction and can be removed to replace the bulbs now.

Oct 11, 2010 | Oldsmobile Alero Cars & Trucks

2 Answers

Change brake light bulb on a 2000 Nissan Frontier


The entire bed line will need to be removed. The long screws that hold the metal bracet where the bed extender attaches also hold the tail light assembly in place.
I pulled the bed liner up at a 45 degree angle and layed it on top of the cab. This revealed the screws. Take both screws out and lay to the side along with the metal bracket for the bed extender.
Now firmly grab the edges of the tail light assembly and pull...there are 2 hard rubber nipples that snap in to hold the assembly. You will feel like you might break it but you won't..just pull straight back hard. The assembly will "POP" out and then you can just twist the back of each bulb there are (3) and pull out..now you will see the bulbs..just pull the bad bulb straight out and push the new one into place. Now just reassemble. Total time will be 30-45 min. for this repair.

Mar 30, 2010 | 2000 Nissan Frontier

2 Answers

My 2005 Audi A6's right brake light and blinker intermittently stop working. I've taken the tail light assembly off, the bulb looks good, and cleaned all of the contacts and it still does it. Could it be...


It is the LED componet in the taillight, not the bulbs that are replaceable. I had the same problem and only solution is to replace the entire assembly.

Mar 09, 2010 | 2005 Audi A6

1 Answer

2004 brake light out (red section) how do I


Not familiar with this model, however see if there are bolts or screws on the side of the tail lamp assembly when you open the tail gate.  Once you remove screws, entire taillamp assembly will come out, and you can then get to back side of tail light to replace bulbs.  This is normal bulb replacement for other pickups like toyota, ford.  Hope this helps!!

Nov 12, 2009 | 2004 Nissan Frontier

1 Answer

Replace rear brake light bulb 1998 lincoln continental


pop the trunk and right behind where the lights are pull the carpet down and their will be of the following depending on the trim.

You will either see the light sockets themselves that you can twist and pull to change the bulb, or you will see the plastic nuts/screws that you can remove to remove the entire assembly in order to access the bulbs.

If it's your 3rd brake light, the screws to access the housing are located in the upper part of the trunk

Oct 26, 2009 | 1997 Lincoln Continental

2 Answers

How do you replace the brake lights?


Open the hatch and look at the back of the brake light assembly, you will see 2 plastic disks with a little slot in the bottom, insert a flat screwdriver into the slots and pop these disks off, they pop off easily Under the disks are phillips head screws, remove both screws Now, you can't see them, but there are 2 pins built into the brake light assembly which extend into sockets in the body of the car, to remove the assembly, wiggle the entire assembly and push outward TO THE SIDE, NOT toward you, this will wiggle the pins free and the entire assembly will come free once the assembly is free you will see 3 plugs, the top 2 are the brake light bulbs, twist the plugs 1/4 turn and pull them out, now you can see the bulbs, just pull them out and replace them

Jul 02, 2009 | 2006 Pontiac Torrent

1 Answer

Brake light bulb replacement.


Remove panel in trunk (round one on each side) reach inside unscrew toggle bolt then remove the entire taillight assembly, may have to push from inside. When you have the taillight assembly out you will see where the bulb is on the back of the assembly, remove and replace with new bulb. Put taillight assembly back in, replace toggle bolt make sure it is tight and replace panel. It is a pain the first time but I have done this 3 or 4 times it gets easier.

May 23, 2009 | 2004 Volkswagen Beetle

2 Answers

Removing rear light assembly on honda odyssey 2006


Yes, there is a "spear point" plastic clip that is still engaged into a socket type holder in the front outboard portion of the tail lamp assembly. Pry gently with a tape wrapped screwdriver at the front outboard corner of the assembly and the clip will release. You will then be able to see how the clip works and will be able to align and engage it first when replacing the tail lamp assembly.

-T

Jan 24, 2009 | 2007 Honda Odyssey

2 Answers

PT Cruiser Brake Light


The bulb in the rear light has burned out and to replace it follow these instructions: 1) go to your owner's manual to find out the part number. You can find and purchase the replacement bulb at Target, any auto parts store and even at Walmart for under $4.00; 2) pop open the trunk door; 3) get a phillips screw driver and unscrew the 2 screws holding the rear brake light fixture to your car body; 4) as soon as you turn over the fixture you'll see where to pull out the burned out bulb and replace it with the new one(s). Good luck!

Jul 14, 2008 | 2006 Chrysler PT Cruiser

Not finding what you are looking for?
2003 Mitsubishi Eclipse Spyder Logo

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...