Question about 1993 Mitsubishi Eclipse

1 Answer

Is there anyway to time the crankshaft with the camshaft without taking off timing cover?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 73 Answers

No you have to take it off

Posted on Jul 01, 2009

Testimonial: "figures"

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am changing the timing chain in a 1993 Chevy S-10 with a 4.3L engine. I was told you have to disconnect a wire to reset it but I don't know where the wire is.


Timing Chain: Service and Repair
REMOVAL
Tools Required = Crankshaft Sprocket Puller
1. Remove the timing cover.
2. Remove the crankshaft position sensor reluctor ring.
3. Remove the camshaft sprocket bolts.
4. Remove camshaft sprocket.
5. Remove timing chain.
6. Remove the crankshaft sprocket.
7. Remove crankshaft sprocket key.

INSTALLATION
1. Install the key into the crankshaft keyway.
2. Use the crankshaft balancer installer to install the crankshaft sprocket.
3. Install the camshaft sprocket and timing chain.
4. Install camshaft sprocket bolts.
Be sure to align the camshaft and the crankshaft sprocket marks. Timing marks (Number 4 Firing).
Tighten bolts to 21 ft. lbs.
5. Align the keyway on the reluctor ring with the key in the crankshaft.
6. Install the reluctor ring onto the crankshaft until the ring is completely seated against the crankshaft sprocket.
7. Install the timing cover.

Don't know what Wire you are referring to.

Jul 30, 2013 | Cars & Trucks

1 Answer

Timing set


Chain

Print


REMOVAL & INSTALLATION

4.3L, 5.0L, 5.7L and 7.4L Engines
See Figures 1, 2, 3, 4, 5 and 6

  1. Remove the timing cover. This will allow access to the timing chain.
  2. Crank the engine until the timing marks on both sprockets are nearest each other and in line between the shaft centers.



0996b43f80219aca.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Crank the engine until the timing marks on both sprockets are in line

  1. On 1996-98 vehicles remove the crankshaft position sensor reluctor ring, if equipped. On 7.4L engines tool J-41371 or its equivalent puller must be used to remove the reluctor ring.
  2. Take out the bolts that hold the camshaft gear to the camshaft. This gear is a light press fit on the camshaft and will come off easily. It is located by a dowel. The chain comes off with the camshaft gear.



0996b43f80219acb.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Remove the camshaft gear retaining bolts


0996b43f80219acc.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Remove the camshaft gear and timing chain
A gear puller will be required to remove the crankshaft gear.
To install:

  1. Without disturbing the position of the engine, mount the new crankshaft gear on the shaft, and mount the chain over the camshaft gear. Arrange the camshaft gear in such a way that the timing marks will line up between the shaft centers and the camshaft locating dowel will enter the dowel hole in the cam sprocket.
  2. Place the cam sprocket, with its chain mounted over it, in position on the front of the truck and pull up with the three bolts that hold it to the camshaft.
  3. After the gears are in place, turn the engine two full revolutions to make certain that the timing marks are in correct alignment between the shaft centers. Tighten the camshaft sprocket bolts (and nut on the 4.3L) to 21 ft. lbs. (28 Nm) on 1988-95 models. On 1996-98 models, tighten the bolts to 18 ft. Lbs. (25 Nm). On the 7.4L, tighten them to 20 ft. lbs. (26 Nm) on 1988-95 models. On 1996-98 models, tighten the bolts to 25 ft. Lbs. (34 Nm).

When installing the crankshaft position sensor you must use install a new oil ring seal onto the sensor.
  1. Install the crankshaft position sensor reluctor ring (if equipped), onto the crankshaft until it is firmly seated against the crankshaft sprocket. On 1996-98 7.4L vehicles replace the reluctor ring with a new component.
  2. Install the front cover, torsional damper, water pump and the radiator.



0996b43f80219acd.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 4: A gear puller will be required to remove the crankshaft gear


0996b43f8020d5d9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 5: Timing mark alignment-4.3L, 5.0L, 5.7L and 7.4L engines

Apr 20, 2013 | 1993 Chevrolet Suburban

1 Answer

Timing belt timing marks


Instructions
  1. Remove the Timing Belt 3.0 V6
    • Place the Voyager's engine in the TDC no. 1 position for cylinder firing in order to get proper alignment. Disconnect the negative cable on the battery.
    • 2Take off the accessory drive belts, and take out engine mount insulator, located in the engine support bracket. Detach the engine support bracket and take off the torsional damper and crankshaft pulleys. This ensures easier access to the timing belt.

    • 3. Locate the 2- to 3-inch wide timing belt in the front of the engine. Remove the cover of the timing belt.
    • 4Mark the course of rotation on the belt as a reference if you plan to reinstall it. Slacken the timing belt torsioner bolt and take off the timing belt. Detach the timing belt torsioner if needed.
    • 5Remove the crankshaft sprocket and the flange shield of the crankshaft sprocket. Secure the camshaft sprocket using a spanner tool MB990775, or something similar, and take off the bolt and washer to the camshaft sprocket.
    Install the Timing Belt
    • 6Use the retaining washer and bolt to fit the camshaft sprocket onto the camshaft. Utilize the spanner tool MB990775 and tighten the bolt. Mount the crankshaft sprocket and put on the timing belt torsioner and tensioner spring if it was removed. Hook the higher end of the spring to the water pump pin and bottom end to the tensioner bracket with the hook facing out.
    • 7Rotate the timing belt tensioner in a counterclockwise turn and tighten the bolt to momentarily hold it in place. Turn the crankshaft sprocket until the timing mark lines up with the timing mark on the oil pump timing mark. Revolve the back camshaft sprocket so that its timing mark lines up with the generator bracket timing mark. Turn the radiator side camshaft sprocket so that the mark aligns with the inner timing belt cover mark.
    • 8Connect the timing belt onto the Voyager's crankshaft sprocket, keeping the belt tight on the side of tension. Install the belt in the same rotational direction if using the original timing belt. Put the timing belt on the radiator side of the camshaft sprocket, and place the belt underneath the water pump pulley first, and follow that by putting it over the back camshaft sprocket and the tensioner.
    • 9Create tension on the side of the timing belt and correctly line up all timing marks. Put the crankshaft sprocket flange into place and loosen the tensioner bolt to allow the tensioner spring to put tension on the belt. Turn the crankshaft two clockwise turns. Line up the timing marks and tighten the tensioner bolt. Put on the timing belt cover and engine support bracket.
    • 10Put the engine mount insulator, crankshaft pulleys and torsional damper into place. Mount the accessory drive belts, connect the negative battery cable and check that the engine runs properly.

Sep 12, 2012 | 1988 Plymouth Voyager

1 Answer

1977 ford pinto timming marks


Hope this helps. Please don't forget to rate....thanks!



c17hydro_169.gif

Crankshaft, camshaft, and distributor timing marks-2300 cc engine (© Ford Motor Co.)


On 2000 cc engines, turn the crankshaft until the two round locating holes in the camshaft pulley are visible from the rear side of the pulley, looking forward from the left-side of the car. When these two holes are parallel to the ground, the timing pointer on the crankshaft pulley should point to TDC. If the drive belt is dislocated, the crankshaft damper will be retarded or advanced 19° per cog on the belt.

If the engine you are working on does not have the two locating holes on the rear side of the camshaft pulley, then you will have to remove the drive belt cover and observe that when the crankshaft timing marks are aligned to TDC of the compression stroke of the No. 1 cylinder, the distributor rotor is pointing to the index mark on the upper lip of the distributor housing which coincides with No. 1 spark plug tower, and the pointer on the camshaft pulley is aligned with the index mark on the cylinder head.

On 2300 cc engines, there is an access plug provided in the cam drive belt cover so that the camshaft timing can be checked without removing the drive belt cover. Remove the access plug, turn the crankshaft until the timing mark on the crankshaft damper indicates TDC, and observe that the timing mark on the camshaft drive sprocket is aligned with the pointer on the inner belt cover. Also, the rotor of the distributor must align with the No. 1 cylinder firing position.


CAUTION:

After any procedure requiring removal of the rocker arms on the 2300, each lash adjuster must be fully collapsed after assembly, then released. This must be done before the camshaft is turned.



Crankshaft, camshaft, and distributor timing marks-2300 cc engine (© Ford Motor Co.)

Crankshaft, camshaft, and distributor timing marks-2300 cc engine (© Ford Motor Co.)
c17hydro_170.gif

Checking 2000 cc overhead camshaft timing (© Ford Motor Co)

May 08, 2011 | Ford Mustang Cars & Trucks

1 Answer

Como poner la banda de tienpo de un toyota camery


Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence.

Dec 23, 2010 | 1993 Toyota Camry V6

1 Answer

How do you set the timming on a 2.3 when your putting the new timming belt on


The IGNITION timing on your Ranger is computer-controlled and is not adjustable.


Should the camshaft drive belt/timing belt jump timing by a tooth or two, the engine could still run; but very poorly. To visually check for correct timing of the crankshaft, auxiliary shaft, and the camshaft follow this procedure:
There is an access plug provided in the cam drive belt cover so that the camshaft timing cam be checked without moving the drive belt cover.
  1. Remove the access plug.
  2. Turn the crankshaft until the timing marks on the crankshaft indicate TDC.
  3. Make sure that the timing mark on the camshaft drive sprocket is aligned with the pointer on the inner belt cover.

Never turn the crankshaft of any of the overhead cam engines in the opposite direction of normal rotation. Backward rotation of the crankshaft may cause the timing belt to slip and alter the timing.
REMOVAL & INSTALLATION

See Figures 1, 2 and 3


0996b43f80211842.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Timing belt cover on the 2.3L and 2.5L engine


0996b43f80211843.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Timing belt assembly on the 2.3L and 2.5L engine


0996b43f80211844.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Releasing the timing belt tensioner using a special tool

  1. Rotate the engine so that No. 1 cylinder is at TDC on the compression stroke. Check that the timing marks are aligned on the camshaft and crankshaft pulleys. An access plug is provided in the cam belt cover so that the camshaft timing can be checked without removal of the cover or any other parts. Set the crankshaft to TDC by aligning the timing mark on the crank pulley with the TDC mark on the belt cover. Look through the access hole in the belt cover to make sure that the timing mark on the cam drive sprocket is lined up with the pointer on the inner belt cover.

Always turn the engine in the normal direction of rotation. Backward rotation may cause the timing belt to jump time, due to the arrangement of the belt tensioner.
  1. Drain cooling system. Remove the upper radiator hose as necessary. Remove the fan blade and water pump pulley bolts.


Dec 11, 2010 | 1995 Ford Ranger Supercab

1 Answer

How to set the timing on 1998 GMC Sierra 5.7


5.0L and 5.7L Engines To Remove:
  1. Remove the crankshaft balancer.
  2. Drain the cooling system.
  3. Remove the water pump.
  4. Drain the engine oil.
  5. Remove all engine oil pan fasteners except two nuts at rear of engine.
  6. Separate the engine oil pan from the front cover.
  7. Disconnect the crankshaft position (CKP) sensor wire. gm-03-50-845.gif

  8. Remove engine front cover. gm-03-50-849.gif

  9. Pry the oil seal from the front cover.
  10. Inspect the front cover seal area and crankshaft balancer seal area for damage. gm-03-50-846.gif

  11. Rotate the crankshaft until the timing marks on the crankshaft and the camshaft sprockets are aligned.
  12. Remove the crankshaft position sensor reluctor ring. gm-03-50-847.gif

    NOTE: Free play on the slack side of the camshaft timing chain must measure less than 0.43 inch (11Mm) or timing chain and sprockets must be replaced.
  13. Remove the camshaft sprocket bolts.
  14. Remove the camshaft sprocket.
  15. Remove the camshaft timing chain. NOTE: Do not turn the crankshaft assembly after the timing chain has been removed in order to prevent damage to the piston assemblies or the valves.
    gm-03-50-848.gif

  16. Remove the crankshaft sprocket using J 5825-A.
  17. Remove the crankshaft balancer woodruff keys (if required).
To Install:
gm-03-50-850.gif

  1. Install the crankshaft balancer woodruff keys into the crankshaft.
  2. Align the crankshaft sprocket keyway with the crankshaft balancer woodruff key. WARNING
    Wear eye protection when installing crankshaft sprocket.
    gm-03-50-851.gif

  3. Use J 5590 to install crankshaft sprocket.
  4. Install the camshaft sprocket and camshaft timing chain. 9308kg61.gif

  5. Ensure that the crankshaft sprocket alignment mark is in the 12 o'clock position and the camshaft sprocket alignment mark is at the 6 o'clock position.
  6. Install the camshaft sprocket bolts and tighten the camshaft sprocket bolts;
    • Torque to: 18 ft. lbs. (25 Nm)
  7. Install the crankshaft position sensor reluctor ring until completely seated against crankshaft sprocket. NOTE: The composite type engine front cover and seal must not be reused. Always install a new engine cover with a new seal.
  8. Install new engine front cover and bolts.
    • Torque bolts to: 106 in. lbs. (12 Nm)
  9. Clean sealer from corners of oil pan gasket where it meets the engine front cover. gm-03-50-775.gif

  10. Apply a 0.196 in (5 mm) bead of adhesive, GM P/N 12346141 or equivalent, 1.0 in (25 mm) long to the engine front cover to engine block junction.
  11. Install oil pan bolts.
    • Torque bolts to: 106 in. lbs. (12 Nm)
  12. Tighten oil pan nuts.
    • Torque bolts to: 18 ft. lbs. (25 Nm)
  13. Connect the crankshaft position sensor wire.
  14. Install the water pump.
  15. Install the crankshaft balancer.
  16. Fill the engine to the proper level with oil.
  17. Fill the engine to the proper level with coolant.
  18. Test drive the vehicle to confirm the repairs.

Nov 05, 2010 | GMC K1500 Cars & Trucks

1 Answer

Camshaft timing mark crankshaft timing mark


Belt covers need to be on. Timing mark on crankshaft (while on compression stroke) should line up with TDC mark on cover. then Camshaft mark, needs to line up by looking through access hole of cover, and align mark on cam sprocket with pointer on inside of belt cover.

Oct 22, 2009 | 1987 Ford Ranger

1 Answer

Timing belt guides


The principle is you have to align TDC ( Top Dead Center) the camshaft, the crankshaft and piston # 1 position at top when both intake valves and exhaust valve are close.
If you follow these following steps, it is a piece of cake.

1- Take off the valve cover to expose the camshaft.
2- Take off all spark plugs2.gif, so you can be able to turn the camshaft without any resistance.
3- Turn the cam shaft until the mark on the camshaft pulley aligned with the 0 calibration mark.
4- Put a screwdriver to into the cylinder # 1 to make sure it is at the top. Then remove it.
5-Turn the camshaft and at the same time notice the intake and exhaust valves for cylinder # 1 are both closed and the notch on the camshaft is aligned straight with the crankshaft mark.
6- For a sanity check, from the spark plug2.gif wire # 1, trace back to the distributor cap. Carefully take off the cap and see the rotor is in the position contact to the plug wire # 1. Then put the cap back as it was.
This is to ensure you have spark at the combustion stage when all valves are close and piston is at the top.
7- With everything is as said, now you put in the timing belt at no turning any position of the crankshaft or the camshaft. If the belt teeth is not aligned correctly, you have to take it out and put it back to provide the mark from crankshaft and camshaft are perfectly aligned.
8- Make sure you loosen up the timing belt tension to put it in easily and tighten it up after have correct tension.
9- Put everything back then you are good to go.
10- Don't forget to replace the Valve cover head gasket to prevent the oil leak.
Good luck and have fun in your hands-on action

Sep 10, 2009 | 1999 Nissan Altima

2 Answers

Need instructions to replace 1993 Toyota Camry Timing Belt


Hi Kmcarroll77

TIMING BELT REPLACEMENT - 2.2L -1993 Toyota Camry

Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence. See Fig. 6 . On MR2, tighten engine
b7619be.jpg
92cabaf.jpg
Hope this helps, don't forget to rate.

Lazaruselite

Feb 25, 2009 | 1993 Toyota Camry V6

Not finding what you are looking for?
1993 Mitsubishi Eclipse Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...