Question about 2001 Chevrolet Corvette

1 Answer

Changing front directioal signal bulb on 2000 corvette need free how to

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Turn your ignition on and your headlights. Turn the key off and then the headlights. They should stay open. Open the hood. Remove the rubber 'bump stop' located next to the headlamp on the side that has the bad bulb. Be careful to not change the location of the lock nut.
Now you have a big opening that will allow you to reach down to the rear of the directional signal and remove the socket and bulb by turning counter clockwise. Replace the bulb. I like to put some dielectric compound or at least some vaseline on the base wires of the new bulb.
Test. Reverse procedure for reassembly. Congratulations....... you just saved $70.00!!! Dave

Posted on Jul 11, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to change front turn signal bulb on 2004 corvette

The front of the vehicle has to be raised up enough to remove the close out panel.This is located by on the side under the front bumper.Should be close to the turn signal lens area.After removing this panel you will need to remove the brake caliper cooling duct from the front fascia and position it aside.Then remove the bulb you need to replace.Then just reverse procedure.Hope this helps.Good luck.Let me know if you have any more questions.

Mar 01, 2011 | Chevrolet Corvette Cars & Trucks

1 Answer

How do you change the turn signal bulb on front passenger on my 2000 corvette?

Do it the easy way! Pop down the brake duct cooling vent on the front fasica and stick your arm, not real comfortable, throught there feeling around for the light bulb. It might take a minute or two to find the first time, but it's not hard. When you find it turn it 1/4 turn and remove it. The wire is long enough to come out of the front opening so you can change the bulb and replace easily. Pop the brake duct back in place and you're done. 5 minutes max first time, I can do it in about 30 seconds now.
Or you can take off the bezel around the headlights and reach down and unplug the light socket. Does not work well with large arms.

- there is an access panel under the front fasica that you can remove and have total access to the area where the lights are. Just have to get the car up off the ground a bit.

Nov 19, 2010 | 2000 Chevrolet Corvette

1 Answer

How to change the front turn signal on a 2001 corvette

For the 2001 Corvette it's simple for replacing it. Using a Sylvania yellow bulb, part# 3157NA LL or 4157NA LL

Reach inside the air intake opening just below the turn signal and push the black friction-fit hose back and down so it is out of your way. With the fingers of one hand, you can press the top of the black plastic duct (air intake) down to make room for your other hand to squeeze into the opening. Reach inside the hole and locate the wiring harness and lamp socket for the turn signal. The harness is on the bottom of the lamp assembly, so that the bulb is essentially sticking upwards into the reflector housing. Turn 1/4 turn and pull wiring harness out of the opening. Change the bulb and reverse the process. Takes about 4 minutes.

Aug 26, 2010 | 2001 Chevrolet Corvette

2 Answers

2000 C5 Corvette turn signals and running lights not working


Mar 02, 2010 | 2000 Chevrolet Corvette

1 Answer

Change front turn signal bulbs

it will be best to use a kitchen fork with the center prongs removed to have this as a tool. the inner skirts front section has round push in clips that will come out if using this fork to pry out with. after removing the plastic baffle you should be able to access the bulb

Feb 27, 2010 | 2000 Chevrolet Corvette

1 Answer

How do you change a burned out front right side turn signal bulb?


Sep 28, 2009 | 2000 Chevrolet Corvette

3 Answers

Left turn signal blinks fast in rear and regular in front

Very simple the bulb is out. When the blinker does that its telling you the bulb needs to be replaced

May 17, 2009 | 2001 Chevrolet Corvette

2 Answers

Replace turn signal bulbs on 2001 corvette

Rears are simply remove the two screws on the lens and remove the tail light from the Vette, twist the connector to get to the bulb. Reverse instructions to install. For the fronts jack up the front, remove the small closeout panel under each side, push the brake cooling duct to one side and twist the bulb socket out of the light to get to the bulb. Reverse instructions to install.

Feb 22, 2009 | 2001 Chevrolet Corvette

2 Answers

Left turn signal

through corvette forum website they give instructions to do it through the headlights.

Nov 05, 2008 | 1999 Chevrolet Corvette

Not finding what you are looking for?
2001 Chevrolet Corvette Logo

228 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

79851 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides