Question about Cars & Trucks

1 Answer

WHY WOUNT MY 2001 4.6 CROWN VIC STAY STARTED MY FUEL PUMP IS GOOD FUEL FILTER IS FLOWING AND STILL NOTHING I AM GETTING FUEL TO THE INJECTORS BUT STILL NOTHING

Posted by Anonymous on

Ad

1 Answer

Battery -was tested
Spark & Injector Pulse-checked
Fuel Pressure -checked
MAF -is plugged in & air filter & ducting in place
At least 20 % fuel load in tank
Checked for OBD 2 Codes

Posted on Aug 18, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 84625 Answers

SOURCE: 1996 Crown Vic, Valve noise under heavy acceleration

No use what's in there, but have the engine de-carboned by a Ford dealer, or remove the octane adjust shorting bar located near the ignition module (retards timing 2 degrees), this will in most cases cure the issue unless there is allot of carbon in the cylinders. There are also methods of ing this de-carbon procedure at home, check on the internet for tips.

PLEASE RATE THIS SOLUTION

Posted on Oct 22, 2008

ltfrc
  • 227 Answers

SOURCE: 2005 Crown Vic Police Interceptor: Starts then stalls

Have you checked the fuel filter. Fuel pump will pressure up, but fuel filter could be clogged and not work without the pressure of the fuel pump.

Posted on Jan 17, 2009

csmock132
  • 4669 Answers

SOURCE: dodge cummins won't start, fuel reaching injector pump but no fuel coming out of injector pump.

You said you have fuel flowing from the inlet line of the injection pump? But not at the injector lines?

Posted on May 05, 2009

  • 1 Answer

SOURCE: 2000 Crown Vic cranks but won't start.

Check the fuel pump reset switch again, if it is popped back out then replace that little switch in the trunk, any ford one will do. it works off a magnet and a bearing to close the circuit for the fuel pump. easy fix.

Posted on Dec 20, 2009

  • 1 Answer

SOURCE: Location of fuel pump relay on a 2001 Ford Crown Vic

where is the fuel pump relay on a 2001 crown vic p71

Posted on Apr 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'M NOT GETTING FUEL TO THE INJECTORS ON A 85 CROWN VIC . THE FUEL PUMP AND THE RELAY HAVE BENN REPLACED WHATS THE NEXT STEP/


You will only get fuel at the injectors when cranking, the pump wont run(Usually) with just the key on. This is to prevent the pump running in a crash and feeding the engine.

May 18, 2014 | 1985 Ford Crown Victoria

3 Answers

Crown vic 2005 no start replaced fuel pump


check your crankshaft position sensor. fuel+spark+compression+timing=ignition.

Mar 13, 2014 | Cars & Trucks

2 Answers

Van stalls intantly- misses bad if I give it gas.. Changed intake gaskets, both o2 sensers, cleaned MAF senser,and changed fuel filter.. Codes read bank 1&2 lean.. Only thing I can think of next is...


It could be a weak pump. To check, have your fuel pressure checked to see if it is correct for your vehicle. On mpfi, pressure should be around 50 psi-check the requirement for your particular vehicle. Then look to the injectors.

Apr 09, 2013 | Cars & Trucks

1 Answer

1999 ford crown vic won't start. changed fuel


Maybe your problem is with the one or many injectors, if just one is bad, you will have problems. Get yourself a multimeter and set it to read in ohms and find what spec the injectors should be at. If out of spec, then you need to replace that one injector(s).

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/cesar_16d20d38798d492f

Mar 25, 2013 | Cars & Trucks

1 Answer

84 crown vic wont start


IF THE PROBLEM IS NOT THE FUEL PUMP, FUEL RELAY, FUEL PRESSURE, AND OR FUSE WAT ELSE COULD B THE PROBLEM

Dec 03, 2011 | 1984 Ford Crown Victoria

3 Answers

2000 Crown Vic cranks but won't start.


Check the fuel pump reset switch again, if it is popped back out then replace that little switch in the trunk, any ford one will do. it works off a magnet and a bearing to close the circuit for the fuel pump. easy fix.

Oct 05, 2009 | 2000 Ford Crown Victoria

4 Answers

My 99 Crown Vic acts like it isn't getting gas


check for clogged fuel filter first, usually the pump works or it dosen't, check and get back to me.

May 01, 2009 | 1988 Ford Crown Victoria

2 Answers

Location of fuel pump relay on a 2001 Ford Crown Vic


where is the fuel pump relay on a 2001 crown vic p71

Jan 10, 2009 | 2001 Ford Crown Victoria

1 Answer

2005 Crown Vic Police Interceptor: Starts then stalls


Have you checked the fuel filter. Fuel pump will pressure up, but fuel filter could be clogged and not work without the pressure of the fuel pump.

Nov 27, 2008 | 2005 Ford Crown Victoria

1 Answer

Engine cuts out , does not throw a code


I also have a 2001 Crown Vic that developed a problem similar to this. It would lope and buck at around 40-45 MPH. I too changed the plugs, then changed the coil boots. It still missed. So I bought 1ea. new coil. After changing the new coil with three old ones, the missing stopped.

Jun 05, 2008 | 2001 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

84625 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

john h

Level 3 Expert

20232 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...