Question about Hyundai Motor 2002 Elantra

1 Answer

2007 hyundai elantrajust had motor rebuilt and refitted motor and keep throwing p0340 code have replaced both cam and crank shalf sensors also check mapping of cam over crank signals still throwing code rebuilder said they removed and clean the cvvt unit what do i try next

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 382 Answers

Dear friend-did the rebuildersnot damage the turn wheel.or is the wiring to the sensor not damaged.

Posted on Jul 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Three codes p0442 p0340 p0742 2006 Hyundai accent 1.6 it cranks but will not start ?


The first code is for an evaporative emission canister leak and it might be due to a gas cap. The second one is for a cam sensor circuit problem and this will keep the vehicle from starting. The third error is for the transmission torque converter.

Mar 11, 2016 | 2006 Hyundai Accent 1.6

1 Answer

I own a 2004 accent with 122,000 km on it. Long story short, had to get a new head gasket put on, so rocker cover, cams, everything had to come off. Work was done and everything was put back together. I...


P0340 - Cam Timing

SYMPTOMS/CONDITIONS
of a mistimed camshaft system (all must apply):
  1. Camshafts have previously been removed from the engine.
  2. Engine runs rough.
  3. Vehicle sets P0340 (camshaft sensor code).
  4. Camshaft sensor has been checked with a known, properly operating camshaft sensor.

CORRECT:
The diagram in the manuals should show the timing marks on both cam gears to be on the blue timing chain links.

ghost45_11.jpg

Mar 23, 2011 | Hyundai Motor 2004 Accent

1 Answer

2002 PT Cruiser no spark at coil -had code P0340 changed cam sensor and no more code but still no spark what else can it be


they can run with out a cam sensor but they will not run with out crank signal i would check for crank signal it may not throw a dtc because it wont start.

Dec 15, 2010 | 2002 Chrysler PT Cruiser

2 Answers

Code p0340 on 2000 dodge intrepid


it might be the cam shaft sensor it might be the crank shaft sensor the best thing to do is replace them bolth. but it does sound like it may be either one because if one goes out the other will still work but when starting the car it will take longer for it to read from either or the one sensor that is still working because they work together to tell the system to deliver the gas. im pretty positive that it is either the cam or crank shaft sensor

Jun 21, 2010 | 2000 Dodge Intrepid

1 Answer

Error code po340 for a 2002 hyundai elantra


Here is what I could find on your P0340 error code:
CausesA code P0340 could mean one or more of the following has happened:
  • a wire or connector in the circuit could be grounded/shorted/broken
  • the camshaft position sensor may have failed
  • the PCM may have failed
  • there exists an open circuit
  • the crankshaft position sensor may have failed
Possible SolutionsWith a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
  • Visually inspect all the wiring and connectors in the circuit
  • Check for continuity in the circuit wiring
  • Check the operation (voltage) of the camshaft position sensor
  • Replace the camshaft position sensor as required
  • Check the crankshaft position circuit as well
  • Replace circuit wiring and/or connectors as required
  • Diagnose/replace the PCM as required
Sounds like since you have replaced both the camshaft and crank shaft sensors you need to look at the PCM.  Go down the line of possible solutions and don't replace the PCM unless nothing else works obviously.  I hope this helps but it looks like you are looking at getting a new PCM.  Good luck.  Thanks for rating my response and for using FixYa!

May 27, 2009 | Hyundai Motor 2002 Elantra

Not finding what you are looking for?
Hyundai Motor 2002 Elantra Logo

296 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

81423 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...