Question about 1992 Honda Accord

1 Answer

Having problems figuring out how to remove the ignition rotar

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 14,036 Answers

First tag or number all plugs wires to distributor cap.then mark rotor location .so it can go back in the same firing position.

Posted on Jul 01, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove front rotors


Hi Richard remove the wheels brake calliper s and mounting brackets then if there is grub screws holding the rotars remove them then get a big hammer and remove thd rotars they get atuck with rust so don't be shy with the hammer. Regards Jim...

Jun 06, 2015 | 2006 Jeep Grand Cherokee

1 Answer

1986 Oldsmobile cutlass keeps cuts off while driving getting gas through carb


Sounds like an ignition problem, bad or worn rotar/rotar cap. bad wires, bad plugs.

Mar 19, 2015 | Oldsmobile Cutlass Cars & Trucks

1 Answer

I have 1985 4.3 fuel injection Monte carlo that when driven for more than 20 to 30 min it will began to boog out or idle down so far that it will cut off and if u try to restart it, it wont start unle


Sound like a lack of fuel. Since you have replaced most of the ignition parts, I would look at the fuel system next.
Could be a clogged fuel filter, weak fuel pump, or pump relay.

Apr 28, 2013 | 1985 Chevrolet Monte Carlo

1 Answer

Trying to change the rotars on my 1991 mitsubishi mirage and there is a plate in between the wheel and the rotar that i cant figure out how to get off


you will need a puller to remove the hub from the spidle, and the rotor bolts on from the rear. or remove the spindle assembly and have a machine shop do it for your, a better idea since the wheel bearing will have to be inspected as well

Nov 06, 2010 | 1991 Mitsubishi Mirage

1 Answer

I have a 93 s10blazer 4.3 vortec 4x4 that wont start. my fuel pump is working i replaced the ignition module, ignition coil, plugs n wires r good, distributor cap and rotar button. idk what it could be


First spray starting fluid in the air filter. If it starts it is a fuel problem. If it doesn't start then pull one of the spark plugs and see if there is spark. If there is not spark then it is an ignition problem.
If it is a fuel problem and the fuel pump is running when you turn the key on, then check fuel pressure. It should be over 35psi.
If it an ignition problem start by checking fire at coil.

Oct 25, 2010 | 1993 Chevrolet S-10 Blazer

1 Answer

My 1989 Chevrolet 1500 4x4 with a 350 stopped running. Checked the fuel pump changed the rotar cap rotar button and the coil. What else could it be?


Replace the pick up coil in the distributor,they are bad to go out.Also,while you are in there remove the ignition module and have it tested,to make sure it is good.

Jul 14, 2010 | 1995 Chevrolet K1500

1 Answer

Removing front rotar


rotar doesn't contain the studs, the plate/hub behind the rotar does - you need a 32mm socket to undo the axle nut to then get at the hub (need a flat screw driver to lever the nut tang up first). If it's seized on put the rotar and wheel back on (leave the axle nut off) and gently rock it in a top-bottom motion (not radially or axially) to free it up. you can then gain access to the hub and studs. put the wheel nuts back on the studs 2 -3 turns so that you have a 'seat' and using a bolt with a smaller dia to punch them out

May 08, 2010 | 1991 Subaru Legacy

1 Answer

Car stalls but starts back up


It had a new cap and rotar and plug wires put on from the people I bought the car from .People told me it started having this problem after they installed the new parts they bought at Autozone so I went and purchased the factory wires ,and dist.cap from a reputable parts store and replaced them and bingo ,no more problem.When buying ignition parts do not go cheap and buy from Autozone.

Mar 14, 2010 | 1994 Geo Prizm

Not finding what you are looking for?
1992 Honda Accord Logo

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...