Question about 1999 Ford F150 Regular Cab

1 Answer

The front panel dont have air conditioned only for down and up the panel

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,826 Answers

There is a actuator motor not working u will have to find it under dash with a flash light,,remove under sheilds and use process of elimination play with remp controll and vent ,defrost,floor etc, and u will find it

Posted on Jul 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the center console where the heater control switches are located on a 2006 Pt Cruiser GT


DESCRIPTION A manual temperature control (MTC) single zone type heating-A/C system or a manually controlled heater-only system is standard equipment on this model, depending on market.
To maintain the performance level of the heating, ventilation and air conditioning (HVAC) system, the engine cooling system must be properly maintained. The use of a bug screen is not recommended. Any obstructions in front of the radiator or A/C condenser will reduce the performance of the A/C and engine cooling systems.
The engine cooling system includes the radiator, thermostat, radiator hoses and the engine coolant pump. Refer to 7 - Cooling for more information before opening or attempting any service to the engine cooling system.

All vehicles are equipped with a common heater, ventilation and air conditioning (HVAC) housing (1). The heating-A/C system combines heating, ventilating and A/C (if equipped) capabilities in a single HVAC housing mounted within the passenger compartment beneath the instrument panel. The HVAC housing includes:
  1. Mode-air doors (2)
  2. A/C evaporator (A/C system only) (3)
  3. Recirculation-air door and actuator (A/C system only) (4)
  4. Blower motor (5)
  5. Mode control cable (6)
  6. Temperature control cable (7)
  7. Heater core (8)
  8. Blend-air door (9)
On heater-only systems, the A/C evaporator is omitted from the HVAC housing and is replaced with an air restrictor plate.
Based upon the system mode selected, conditioned air can exit the standard heater-only or optional heater-A/C housing through one or a combination of the three main housing outlets: defrost, panel or floor. The defrost and panel outlets are located on the top of the HVAC air distribution housing and the floor outlets are located on each side of the distribution housing. Once the conditioned air exits the HVAC housing, it is further directed through molded plastic ducts to the various outlets within the vehicle interior. These outlets and their locations are as follows:
  1. Defroster Outlet- A single large defroster outlet is located in the center of the instrument panel top cover, near the base of the windshield.
  2. Side Window Demister Outlets- There are two side window demister outlets, one is located at each outboard end of the instrument panel top cover, near the belt line at the A-pillars.
  3. Panel Outlets- There are four panel outlets in the instrument panel, one located near each outboard end of the instrument panel facing the rear of the vehicle and two located near the top of the instrument panel center bezel.
  4. Front Floor Outlets- There are two front floor outlets, one located on each side of the center tunnel near the dash panel.
  5. Rear Floor Outlets- There are two rear floor outlets, one located on each side of the floor panel center tunnel near the front of each rear seat foot well.
  6. REMOVAL
    WARNING: Disable the airbag system before attempting any steering wheel, steering column, or instrument panel component diagnosis or service. Disconnect and isolate the negative battery (ground) cable, then wait two minutes for the airbag system capacitor to discharge before performing further diagnosis or service. This is the only sure way to disable the airbag system. Failure to follow these instructions may result in accidental airbag deployment and possible serious or fatal injury.


    NOTE: Illustration shown with instrument panel removed for clarity. (Refer to 23 - Body/Instrument Panel/BEZEL, Instrument Panel - Removal).(Refer to 24 - Heating and Air Conditioning/Controls/CONTROL, A/C and Heater - Removal).(Refer to 23 - Body/Instrument Panel/COVER, Steering Column Opening - Removal). 5. Remove the screw (1) that secures the temperature control cable (2) to the left side of the HVAC air distribution housing (3). 6. Disconnect the temperature control cable from the blend door pivot lever (4) and remove the cable from the vehicle.
    REMOVAL

    WARNING: Disable the airbag system before attempting any steering wheel, steering column, or instrument panel component diagnosis or service. Disconnect and isolate the negative battery (ground) cable, then wait two minutes for the airbag system capacitor to discharge before performing further diagnosis or service. This is the only sure way to disable the airbag system. Failure to follow these instructions may result in accidental airbag deployment and possible serious or fatal injury. (Refer to 24 - Heating and Air Conditioning/Controls/CONTROL, A/C and Heater - Removal).(Refer to 08 - Electrical/Clock - Removal).(Refer to 08 - Electrical/Power Windows/SWITCH, Power Window - Removal).(Refer to 24 - Heating and Air Conditioning/Distribution/OUTLET, Air - Removal).

Oct 31, 2016 | Cars & Trucks

1 Answer

My husband incorrectly connected the battery up and now stereo, stereo illumination, central locking . interior lights, air conditioning graghics dont work now. Cant find internal fusebox? Help me please


Usually in the drivers side panel under steering console.if not look under hood near wheel arch....or passenger footwell.it sounds like the main 20-30 amp fuse blew.did he get negative and positive terminals back to front so it went to positive earth?

Feb 19, 2015 | Cars & Trucks

1 Answer

How to fix the back control panel for the heater and airconditioning


your low on gas ,a twin unit normally has 1.2 kgs of gas and i suspect your down to around 500 grms of gas

Jul 08, 2012 | 1996 Chevrolet Suburban

1 Answer

Need to remove heater A/C dash control , what is proper procedure?


Look at fig. 4 for the heater a/c dash control: HEATER CORE Altima REMOVAL AND INSTALLATION
  1. Position the steering wheel in the straight-ahead position.
  2. Turn the ignition switch OFF.
  3. Disconnect the negative (() battery cable; then, the positive (+) battery cable. NOTE: Wait for a least 3 minutes after disconnecting the battery cables for the charge in the air bag circuit to dissipate before working on the air bag module(s).
  4. Remove the driver's side SRS and steering wheel by removing or disconnecting the following:
    • Lower lid from the steering wheel and disconnect the driver's air bag module connector
    • Left and right side lids from the steering wheel
    • Special bolts from both side of the steering wheel using a tamper resistant Torx wrench (T50)
    • Air bag module and store it face up
    • Horn's electrical connector and remove the steering wheel nut
    • Steering wheel from the steering column using a suitable puller
  5. Remove the passenger's side SRS by removing or disconnecting the following:
    • Glove box door and the glove box
    • Front passenger's air bag module connector
    • 2 special bolts using a tamper resistant Torx wrench (T50)
    • 4 passenger's air bag-to-instrument panel nuts
    • Front passenger's air bag module and store it face up.
  6. Drain the cooling system into a clean container for reuse.
  7. Discharge and recover the air conditioning system refrigerant.
  8. Working in the engine compartment, disconnect the heater hoses from the heater core tubes.
  9. Remove the instrument panel by removing or disconnecting the following:
    • Kick plate and dash side finisher on the driver's side
    • 2 lower panel-to-instrument panel screws and the lower panel on the driver's side
    • 2 lower reinforcement panel-to-instrument panel screws and the lower reinforcement panel
    • 6 steering column cover screws, the covers, the spiral cable and combination switch
    • 2 cluster lid "A" screws and the cluster lid "A"
    • 3 combination meter screws, disconnect the electrical harness connector and remove the combination meter
    • Switch panel
    • Instrument panel lower covers
    • Snap out the transmission shifter finisher (boot)
    • 4 cluster lid "C" screws and the cluster lid "C"
    • 4 audio and deck pocket-to-instrument panel screws and the audio and deck pocket
    • 5 center console screws and the center console
    • 2 center instrument panel screws and the center panel
    • front defroster grilles
    • Front pillar garnish
    • Instrument panel 3 nuts/4 screws and the instrument panel
    • 8 instrument stay assembly nuts and the stay
    • Steering member assembly 5 nuts/1 bolt and the steering member
  10. Remove the air conditioning housing assembly by removing or disconnecting the following:
    • Refrigerant lines from the air conditioning housing assembly
    • Thermo control amp
    • Air conditioning housing assembly
  11. Remove or disconnect the following:
    • Heater unit
    • Heater core from the heater unit Fig. 1: Exploded view of the steering wheel and air bag module 93112gd9.gif
      Fig. 2: Exploded view of the passenger's side air bag module 93112gd0.gif
      Fig. 3: Exploded view of the instrument panel assembly 93112ge1.gif
      Fig. 4: Exploded view of the heater housing assembly and related components 93112ge2.gif
      Fig. 5: View of the heater core and heater housing 93112ge3.gif
    To install:
  12. Install or connect the following:
    • Heater core to the heater unit
    • Heater unit
  13. Install the air conditioning housing assembly by installing or connecting the following:
    • Air conditioning housing assembly
    • Thermo control amp
    • Refrigerant lines to the air conditioning housing assembly
  14. Install the instrument panel by installing or connecting the following:
    • Steering member assembly and the steering member 5 nuts/1 bolt
    • Instrument stay assembly and the 8 stay nuts
    • Instrument panel and the instrument panel 3 nuts/4 screws
    • Front pillar garnish
    • Front defroster grilles
    • Center instrument panel and the 2 center panel screws
    • Center console and the 5 center console screws
    • Audio and deck pocket and the 4 audio and deck pocket-to-instrument panel screws
    • Cluster lid "C" and the 4 cluster lid "C" screws
    • Snap in the transmission shifter finisher (boot)
    • Instrument panel lower covers
    • Switch panel
    • Combination meter, connect the electrical harness connector and install the 3 combination meter screws
    • Cluster lid "A" and the 2 cluster lid "A" screw
    • Combination switch, the spiral cable, the covers and the 6 steering column cover screws
    • Lower reinforcement panel and the 2 lower reinforcement panel-to-instrument panel screws
    • Lower panel and the 2 lower panel-to-instrument panel screws, on the driver's side
    • Kick plate and dash side finisher, on the driver's side
  15. Working in the engine compartment, connect the heater hoses to the heater core tubes.
  16. Install the passenger's side SRS by installing or connecting the following:
    • Front passenger's air bag module
    • 4 passenger's air bag-to-instrument panel nuts
    • 2 new special bolts and torque using a tamper resistant Torx wrench (T50) to 11-18 ft. lbs. (15-25 Nm)
    • Front passenger's air bag module connector
    • Glove box door and the glove box
  17. Install the driver's side SRS and steering wheel by installing or connecting the following:
    • Steering wheel to the steering column
    • Steering wheel nut and torque the nut to 22-29 ft. lbs.
    • Horn's electrical connector
    • Air bag module
    • New special bolts to both sides of the steering wheel and torque the bolts using a tamper resistant Torx wrench (T50) to 11-18 ft. lbs. (15-25 Nm).
    • Both the left and right side lids to the steering wheel
    • Lower lid to the steering wheel and connect the driver's air bag module connector
  18. Refill the cooling system.
  19. Connect the positive (+) battery cable; then, the negative (() battery cable.
  20. Evacuate, charge and leak test the air conditioning system refrigerant.
  21. Operate the engine to normal operating temperatures; then, check the climate control operation and check for leaks.

Nov 19, 2010 | 2002 Nissan Sentra

1 Answer

2003 Chevy trailblazer, the 4 front dash air


{: ) Check first the fuse labeled HVAC1 10A at the rear fuseblock. If okay, the mode actuator could be faulty. You can try this: turn ignition switch and a/c off for a minute. Then turn ignition on, wait forty seconds. Afterwards, start the engine, and check your a/c again.

Aug 01, 2010 | 2006 Chevrolet Trailblazer

3 Answers

Looking to replace heater core


Cherokee, Grand Cherokee, 1999-2005

Removal & Installation
  1. Disconnect and remove the negative battery.
    CAUTION After disconnecting the negative battery cable, wait 2 minutes for the driver-s/passenger-s air bag system capacitor to discharge before attempting to do any work around the steering column or instrument.
  2. Drain the cooling system into a clean container for reuse.
  3. Remove the instrument panel by performing the following procedure:
    1. Turn the steering wheel in the straight-ahead position.
    2. Remove the knee blocker from the instrument panel.
    3. Remove the steering column; do not remove the air bag module, the steering wheel or switches from the steering column.
    4. From under the driver-s side of the instrument panel, disconnect the following items:

      Instrument panel wiring harness connector from the 100-way wiring harness connector at the left side of the inner panel. Side window demister hose at the heater/air conditioning housing demister/defroster duct on the driver-s side.
    5. Remove the glove box.
    6. Reaching through the glove box opening, disconnect the following items:

      Two halves of the heater/air conditioning system vacuum harness connector. Instrument panel wiring harness connector from the heater/air conditioning system wiring harness connector. Instrument panel wiring harness connector from the passenger-s side air bag module wiring harness connector. Side window demister hose at the heater/air conditioning housing demister/defroster duct (passenger-s side). Two halves of the radio antenna coaxial cable connector. Two instrument panel wiring harness connectors from the passenger air bag ON/OFF switch wiring harness connector. Passenger-s side air bag ON/OFF switch wiring harness from the retainer clip on the plenum bracket that supports the heater/air conditioning housing just inboard of the fuse block module. Two lower passenger-s side air bag module bracket-to-dash panel nuts.
    7. Remove the upper cover from the instrument panel.
    8. Remove the 3 instrument panel-to-door hinge pillar screws.
    9. Remove the 4 upper instrument panel-to-dash nuts.
    10. Using an assistant, remove the instrument panel from the vehicle.
  4. If equipped with air conditioning, discharge and recover the air conditioning system refrigerant.
  5. Disconnect the refrigerant lines from the evaporator. Plug the refrigerant openings to prevent evaporation.
  6. Disconnect the heater hoses from the heater core tubes.
  7. Disconnect the heater/air conditioning system vacuum supply line connector from the T-fitting near the heater core tubes.
  8. In the engine compartment, remove the 5 heater/air conditioning housing-to-chassis nuts. If necessary, loosen the battery hold-downs and reposition the battery for access.
  9. Remove the cowl plenum drain tube from the heater/air conditioning housing stud; it-s located behind the cylinder head on the cowl.
  10. From the bottom of the heater/air conditioning housing, remove the floor duct.
  11. On the passenger side, remove the heater/air conditioning housing-to-plenum bracket screw.
  12. Pull the heater/air conditioning housing down far enough to clear the defrost/demist and fresh air ducts, then, rearward far enough to clear the mounting studs and the evaporator drain tube to clear the dash panel holes.
  13. Remove the heater/air conditioning housing assembly from the vehicle.
  14. Remove the heater/air conditioning housing upper case.
  15. Lift the heater core from the lower half of the heater/air conditioning housing.
To install:
  1. Assemble the heater core into the lower half of the heater/air conditioning housing.
  2. Install the heater/air conditioning housing upper case.
  3. Install the heater/air conditioning housing assembly to the vehicle.
  4. On the passenger-s side, install the heater/air conditioning housing-to-plenum bracket screw.
  5. At the bottom of the heater/air conditioning housing, install the floor duct.
  6. Install the cowl plenum drain tube to the heater/air conditioning housing stud; it-s located behind the cylinder head on the cowl.
  7. In the engine compartment, install the 5 heater/air conditioning housing-to-chassis nuts.
  8. Connect the heater/air conditioning system vacuum supply line connector to the T-fitting near the heater core tubes.
  9. Connect the heater hoses to the heater core tubes.
  10. Connect the refrigerant lines to the evaporator.
  11. If equipped with air conditioning, evacuate and charge the air conditioning system refrigerant.
  12. Install the instrument panel by performing the following procedure:
    1. Using an assistant, install the instrument panel to the vehicle.
    2. Install the 4 upper instrument panel-to-dash nuts.
    3. Install the 3 instrument panel-to-door hinge pillar screws.
    4. Install the upper cover to the instrument panel.
    5. Reaching through the glove box opening, connect the following items.

      Two lower passenger-s side air bag module bracket-to-dash panel nuts. Passenger-s side air bag ON/OFF switch wiring harness to the retainer clip on the plenum bracket that supports the heater/air conditioning housing just inboard of the fuse block module. Two instrument panel wiring harness connectors to the passenger air bag ON/OFF switch wiring harness connector. Two halves of the radio antenna coaxial cable connector. Side window demister hose at the heater/air conditioning housing demister/defroster duct (passenger-s side). Instrument panel wiring harness connector to the passenger-s side air bag module wiring harness connector. Instrument panel wiring harness connector to the heater/air conditioning system wiring harness connector. Two halves of the heater/air conditioning system vacuum harness connector.
    6. Install the glove box.
    7. Under the driver-s side of the instrument panel, connect the following items:

      Side window demister hose at the heater/air conditioning housing demister/defroster duct on the driver-s side. Instrument panel wiring harness connector to the 100-way wiring harness connector at the left side of the inner panel.
    8. Install the steering column.
    9. Install the knee blocker to the instrument panel.

  13. Connect and remove the negative battery.
  14. Refill the cooling system.
  15. Run the engine to normal operating temperatures; then, check the climate control operation and check for leaks.

Hope helps (remember rated this).

Jun 25, 2010 | 2001 Jeep Grand Cherokee

1 Answer

I have a 1992 mercedes 200 E WDB 021 Saloon, it has 8 button air condition and I dont know how to use it. Control wheel on blue position but When I push the button (leftmost)which has a glass figure on it,...


The pulley on the air condition has to turn it has a belt on it. The Compressor engages to pre cool the evaporator. Most likely you have a blend door pod leak or leak in the hose or the sampler valve is bad. I would replace the sampling valve behind the glove box/air bag. As that reads the cabin temp and if it thinks the car is cold the heat will stay on because everything is automatic. All vents will blow cold when it thinks its hot and in addition to floor and corner dash center vents will blow cold when it works. If the direction of air is correct then the A/C system may have a leak or need a charge of freon.

May 05, 2010 | 1992 Mercedes-Benz E-Class

1 Answer

How do you remove the head unit on a 2009 f150


Remove the little rubber mat in front of the display, remove the 2 screws, then where the microsoft with sync is pop that out and remove the one screw there. You will have to pop out the side panels near the radio/ air condition panel then you will be able to pop out the panel for the radio/air condition panel. There are four screws for the cd player and four torx screws for the radio panel.

Nov 15, 2009 | 2009 Ford F-150

1 Answer

How to Replace a Heater Core


Removal & Installation

  1. Disconnect the negative battery cable.
    CAUTION After disconnecting the negative battery cable, wait 2 minutes for the driver-s/passenger-s air bag system capacitor to discharge before attempting to do any work around the steering column or instrument
  2. On diesel models, remove the passenger side battery and battery tray.
  3. Remove the instrument panel by performing the following procedures:
    1. Remove the air bag control module (ACM) and bracket from the floor panel tunnel.
    2. Remove the trim from both cowl side inner panels.
    3. Remove the steering column-to-instrument panel opening cover.
    4. Remove the 2 hood latch release handle-to-instrument panel lower reinforcement screws and lower the handle to the floor.
    5. Disconnect the driver-s side air bag module wiring harness connector from the lower instrument panel reinforcement.
    6. Place the wheels in the straight-ahead position and lock the steering wheel. Remove the steering column without disassembling it.
    7. From under the driver-s side of the instrument, disconnect or remove the following items:

      Parking brake release handle linkage rod from the parking brake mechanism located on the left cowl side inner panel. Instrument panel wiring harness connector from the parking brake switch located on the parking brake mechanism. Three wiring harness connectors (body wiring harness, headlight, dash) from the 3 junction block connector receptacles located closest to the dash panel. Head light/dash-to-instrument panel bulkhead wiring harness connector screw and disconnect the connector. Instrument panel-to-door wiring harness connector located directly below the bulkhead wiring harness connector. Infinity sound system wiring harness connector (if equipped), located at the outboard side of the instrument panel bulkhead connector. Stop light switch electrical connector. Vacuum harness connector located near the left side of the heater/air conditioning housing.
    8. Under the passenger-s side of the instrument panel, disconnect the radio antenna coaxial cable connector.
    9. Loosen both sides of the instrument panel cowl side roll-down bracket screws about 1 / 2 inch (13mm).
    10. Remove the 5 upper instrument panel-to-upper dash panel screws; remove the center screw last.
    11. Roll down the instrument panel and install a temporary hook in the center hole on top of the panel. Attach the other end to the center hole in the top of the dash panel. The opening should be approximately 18 inches (46cm).
    12. Disconnect the instrument panel-to-heater/air conditioning housing assembly wiring harness connectors.
    13. Using an assistant, remove the instrument panel from the vehicle.

  4. If equipped with air conditioning, perform the following procedure:
    1. Discharge and recover the air conditioning system refrigerant.
    2. Disconnect the refrigerant lines from the evaporator. Plug the openings to prevent contamination.
    3. Disconnect the refrigerant lines from the accumulator. Plug the openings to prevent contamination.
    4. Remove the accumulator.

  5. Drain the cooling system into a clean container for reuse.
  6. Disconnect the heater hoses from the heater core tubes.
  7. Remove the PCM from the dash panel and move it aside. Do not disconnect the PCM harness connector.
  8. In the engine compartment, remove the heater/air conditioning housing assembly-to-chassis nuts.
  9. In the passenger-s compartment, remove the heater/air conditioning housing-to-dash panel nuts.
  10. Pull the heater/air conditioning housing assembly rearward far enough to clear the studs and air conditioning drain tube holes.
  11. Remove the heater/air conditioning housing assembly from the vehicle.
  12. Remove the upper-to-lower heater/air conditioning housing screws and remove the upper housing.
  13. Remove the heater core from the lower housing.


    Fig. View of the heater/air conditioning housing assembly


    0900c15280225dc3.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. View of the heater core

Apr 07, 2009 | 1997 Dodge Ram

Not finding what you are looking for?
1999 Ford F150 Regular Cab Logo

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...